Operation Guide GB
Table Of Contents
- CONTENTS
- INTRODUCTION
- USING THE MANUAL
- DIFFERENCES BETWEEN MODELS
- SETUP
- BEFORE USING THE MACHINE
- COPY FUNCTIONS
- PRINTER FUNCTIONS
- BASIC PRINTING
- PRINTER DRIVER SETTING SCREEN
- SETTING ADVANCED PRINT FUNCTIONS
- PRINTING MULTIPLE PAGES ON ONE PAGE (N-Up Printing)
- FITTING THE PRINTED IMAGE TO THE PAPER (Fit To Paper Size)
- ROTATING THE PRINT IMAGE 180 DEGREES (Rotate 180 degrees)
- ENLARGING/REDUCING THE PRINT IMAGE (Zoom)
- PRINTING FAINT TEXT AND LINES IN BLACK (Text To Black/Vector To Black)
- ADJUSTING THE BRIGHTNESS AND CONTRAST OF THE IMAGE (Image Adjustment)
- ADDING A WATERMARK TO PRINTED PAGES (Watermark)
- TWO-SIDED PRINTING (Model that has duplex copy / print function as standard feature only)
- SAVING FREQUENTLY USED PRINT SETTINGS
- OUTLINE OF THE PRINT STATUS WINDOW
- BASIC PRINTING (MACINTOSH)
- SCANNER FUNCTIONS
- USER SETTINGS
- TROUBLESHOOTING
- ROUTINE MAINTENANCE
- APPENDIX
- WEB FUNCTIONS IN THE MACHINE
- ABOUT THE WEB PAGES
- CHECKING THE IP ADDRESS IN THE WEB PAGE
- ABOUT THE WEB PAGES (FOR USERS)
- CONFIGURING THE PRINTER CONDITION SETTINGS
- ABOUT THE WEB PAGES (FOR THE ADMINISTRATOR)
- PROTECTING INFORMATION PROGRAMMED IN THE WEB PAGE ([Passwords])
- ADMINISTRATOR SETTINGS
- SSL SETTINGS
- E-MAIL STATUS AND E-MAIL ALERT SETTINGS
65
COPY FUNCTIONS
3
ID CARD COPY
You can copy the front and back sides of ID card onto a page through this function. The specified patterns of ID card
copy are shown as follows.
1
Press the [ID CARD COPY] key.
The ID CARD COPY
indicator will light up.
2
Place the ID card on the document
glass, align with the ID card mark, and
press the [START] key ( ).
When scanning, ORIGINAL DATA
indicator will blink after scan is finished,
ORIGINAL DATA indicator will go off and one
side of the ID card is scanned into memory. (In
this case, print will start if pressing [READ-END]
key ( ).)
3
Turn the ID card to the other side, and
press the [START] key ( ).
When scan finished, Copy will begin.
Pattern 2
Pattern 1
Front
Back
Centre Line
Front
Back
• Select the layout patterns as explained in "ID card" of SYSTEM SETTINGS (p.93) first, then follow the steps
below to perform the copy. For changing a system setting, refer to "SELECTING A SETTING FOR A SYSTEM
SETTING" (p.94).
• ID card copy feature cannot be used in combination with interrupt copy, two-sided copy, dual page copy,
XY-zoom, margin shift, edge + centre erase, 2 in 1/4 in 1, sort/group and rotation copy functions.
• The following paper sizes can be used:
Pattern 1: A4 (8-1/2''x11'') is recommended.
Pattern 2: A5 to A3 ((5-1/2''x8-1/2'' to 11"x17"). (A5 (5-1/2''x8-1/2'') can only be used in bypass tray.)
• When using Pattern 1, the image may cut off even if using standard paper size.
• In ID card mode, refer to "CUSTOMISING SETTING (system settings)"(page 86), if you want to set the number
of copies. Scan area is: X: 98mm, Y: 66mm.
• Auto paper selection and auto tray switch are invalid in ID card copy mode. Please select paper and tray
manually.
• The ID card should be placed 5mm from the original size scale in order that the image will not be cut off when
copying.
• For ID card copy, enlargement ratios can be selected. However, depending on the paper size, copy image may
be an omission.
Note
To cancel ID card copy, press the [CLEAR
ALL] key ( ) and make sure the ID CARD
COPY indicator is off.
Note