Service manual

Hardware Specs
a. Base Memory
Value: 16 MB
Example: 16 MB
Default: 16 MB
Description: It indicates base memory quantity of the printer board.
Basically, this is fixed at 16 MB and it cannot be
changed.
b. Optional Memory
Value: (0|16|32|48|64) MB
Example: 0MB
Default: 0MB
Description: It indicates the printer board’s optional memory quantity.
The customer (serviceman) could extend the memory
by attaching 72pin-SIMM. 0MB means optional memory
is not attached. 16MB or 32MB SIMM can be used to
this purpose.
c. Total Memory
Value: (16|32|48|64|80) MB
Example: 16MB
Default: 16MB
Description: It indicates the printer board’s total memory quantity. In
other words, it is summation of Base Memory and Op-
tion Memory.
d. Copier HDD
Value: 4GB
Version Information
a. PRT
Value: #.##
Example: 2.00
Default: Depends on printer firmware version
Description: This number should be same as the PRT-PRG ROM
version number seen on serviceman simulation 22-5.
b. BOOT
Value: #.##
Example: 2.00
Default: Depends on printer firmware version
c. ICU
Value: #.##
Example: 2.00
Default: Depends on printer firmware version
Description: This number should be same as the ICU ROM version
number seen on serviceman simulation 22-5.
Installed Device
a. Duplex Module
Value: (Yes | No)
Example: Yes
Default: Depends on the Machine configuration
Description: It indicates that duplex unit is attached or not.It depends
on hardware configuration.
b. Output Device
Value: (Standard 1 Tray | Standard 2 Trays | 3 Tray Finisher|2
Tray Finisher)
Example: 3 Tray Finisher
Default: Depends on the Machine configuration
Description: It indicates attached output device.. It depends on
hardware configuration.
c. Paper Input Trays
Value: (2 trays | 3 trays | 4 trays)
Example: 2 trays
Default: Depends on the Machine configuration
Description: It indicates the number of standard input trays.It
depends on hardware configuration.
d. Large Capacity Tray
Value: (Yes | No)
Example: Installed
Default: Depends on the Machine configuration
Description: It indicates that large capacity paper input tray(Large
Capacity Tray) is attached or not. It depends on
hardware configuration.
e. Interface Board
Value: (None | Ethernet | TokenRing)
Example: Ethernet
Default: Depends on the Machine configuration
Description: It indicates the kind of installed network card option to
the slot. 10Base-T/2 and 10/100Base-T are not iden-
tified. Those two will be reported as Ethernet.
TokenRing would not be supported for AR-PB1 (AR-
PB2) for Japan domestic.
Available Paper Size
Appearance on
Configuration Page
Description
Letter (81/2x11) Letter / Long Edge Feed
Letter (81/2x11R) Letter / Short Edge Feed
Legal (81/2x14) Legal / Short Edge Feed
Ledger (11x17) Ledger / Short Edge Feed
Executive (7 1/4x101/2) Executive / Short Edge Feed
Invoice (5 1/2x81/2) Invoice / Long Edge Feed
Foolscap (81/2x13) Foolscap / Short Edge Feed1
A4 A4 / Long Edge Feed
A4R A4 / Short Edge Feed
B5 B5 / Long Edge Feed
B5R B5 / Short Edge Feed
B4 B4 / Short Edge Feed
A3 A3 / Short Edge Feed
A5 A5 / Long Edge Feed
A6 A6 / Short Edge Feed
Japanese Postcard Japanese Postcard / Short Edge Feed
(Unknown) Other size (EXTRA)
(No Paper) No paper available on this tray.
(No Tray) There is a problem with this tray.
(Tray Open)
This tray is opened (except Bypass-Tray)
or Tray is lifting up.
a. Tray 1 / Tray 2 / Tray 3 / Tray 4
Value: [Appropriate Paper Size]
Example: Letter (81/2x11)
Default: Depends on paper tray configuration.
Description: It indicates paper size configuration of Tray 1 /2 / 3 / 4 /
5. It depends on hardware configuration, not software
condition.
(Unknown) means paper size cannot be identified. (Tray
configuration is "EXTRA".)
This line is not printed for unavailable tray.
AR-PB2A
5 – 2