Service manual

AR-M208 SIMULATION 8 - 13
[7-seg LED display]
1: Self print (2-by-4) mode
2: Grid print mode
Pressing the [START] key makes a print by 2 by 4 mode. After comple-
tion of printing, the menu returns to the initial menu.
Pressing the [CA] key cancels the simulation mode.
Operation/procedure (Pattern 1)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
Operation/procedure
Download PCL.
Pressing the [OK] key displays "Please Send Data" "Ready" and the
data is sent from the PC under the MS-DOS command of FCOPY and
the file name.
Used to overwrite and check the flash device while displaying its pro-
cess status.
After completion, the result is displayed.
(It takes a little time to display READY.)
Press the [CA] key to cancel the simulation and reset.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
Operation/procedure (Pattern 7)
Pressing the [OK] key displays the confirmation message.
Press the [OK] key again to clear. Press the [BACK] key to interrupt
clearing.
If there is no abnormality after Clear operation, "COMPLETE" is dis-
played. If there is any abnormality, "ERROR" is displayed.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
Operation/procedure (Pattern 7)
Pressing the [OK] key displays the confirmation message.
Press the [OK] key again to clear. Press the [BACK] key to interrupt
clearing.
If there is no abnormality after Clear operation, "COMPLETE" is dis-
played. If there is any abnormality, "ERROR" is displayed.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL is installed.
(Input screen) (Executing screen)
67
67-11
Purpose Setting
Function (Purpose) Used to set the Select-IN signal.
Setting range 0-1
Default 0
67-14
Function (Purpose) Used to check write/comparison of flash
programs.
(1) (2) (3)
(Normal end screen) (Abnormal end screen)
Sim67-11 SELECT-IN
SELECT-IN SIGNAL 0
(0:ON 1:OFF)
[ 0- 1] 0
Sim67-14 FLASH D/L
PRESS OK KEY
Sim67-14 FLASH D/L
Please Send Data
READY
Sim67-14 FLASH D/L
PROGRAM
RECEIVE
Sim67-14 FLASH D/L
COMPLETE
Sim67-14 FLASH D/L
FAILED
(Flash Device)
PROGRAM
BOOTROM
PS KANJI FONT
ESC/P KANJI FONT
OPTION FONT
(Processing state)
RECEIVE
ERASE
WRITE
VERIFY
67-17
Function (Purpose) Used to clear NVRAM.
(Initial screen) (Process check screen) (Executing screen)
(Normal end screen) (Abnormal end screen)
67-18
Function (Purpose) Used to clear the data area for FLASH ROM
Network Scanner Application.
(Initial screen) (Process check screen) (Executing screen)
(Normal end screen) (Abnormal end screen)
Sim67-17 NVRAM CLR.
NVRAM CLEAR
PRESS OK KEY
Sim67-17 NVRAM CLR.
NVRAM CLEAR
ARE YOU SURE?
Sim67-17 NVRAM CLR.
NVRAM CLEAR
NOW DOING...
Sim67-17 NVRAM CLR.
NVRAM CLEAR
COMPLETE
PRESS OK KEY
Sim67-17 NVRAM CLR.
NVRAM CLEAR
ERROR
PRESS OK KEY
Sim67-18 APP. CLR.
APP. DATA CLEAR
PRESS OK KEY
Sim67-18 APP. CLR.
APP. DATA CLEAR
ARE YOU SURE?
Sim67-18 APP. CLR.
APP. DATA CLEAR
NOW DOING...
Sim67-18 APP. CLR.
APP. DATA CLEAR
COMPLETE
PRESS OK KEY
Sim67-18 APP. CLR.
APP. DATA CLEAR
ERROR
PRESS OK KEY