Service manual

AR-M208 SIMULATION 8 - 8
Operation/procedure
The current setup is displayed with ON or OFF.
Enter an input (20 digits) of the PS expansion kit soft key and press the
[OK] key, and the collating result is displayed with OK or NG.
After canceling the simulation, if OK, the PS expansion kit function is
enable; if NG, the PS expansion kit function is disabled.
This setting must be reset after the simulation cancel.
* Execution is inhibited until GDI or PCL board is securely installed.
(Because the board is detected by the software.)
Note: Executable only when the PCL/PS3 is installed.
Operation/procedure
Select the language to be used according to the table below.
This setup varies in connection with SIM 26-6 (Destination setup).
Operation/procedure
AMS mode is set when setting the pamphlet (center binding) function.
Operation/procedure
Input the set value with the 10-key and press the [OK] key.
If a model different from CPM setup (22cpm or 27cpm) of BOOT is set,
a system error will occur after canceling the simulation.
Operation/procedure
After the mode selection, enter the adjustment value and press the
[OK] key.
26-14
Function
(Purpose)
Used to input the Software Key for the PS extension
kit.
(Initial screen) (In case of OK) (In case of NG)
26-22
Purpose Setting
Function
(Purpose)
Used to set the specification (language display) for the
destination.
Item Specifications
Display items
Setting
range
Default
0:JAPANESE 11:GREEK
0-20 1
1:ENG.US 12:POLISH
2:ENG.UK 13:HUNGARIAN
3:FRENCH
14:CZECH
4:GERMAN 15:RUSSIAN
5:ITALIAN 16:FINNISH
6:DUTCH 17:NORWEGIAN
7:SWEDISH 18:DANISH
8:SPANISH 19:CHINESE
9:PORTUGUESE
20:TAIWANESE
10:TURKISH
–
26-41
Purpose Setting
Function
(Purpose)
Used to set whether the automatic magnification ratio
select (AMS) is always ON or not when setting the
pamphlet (center binding) function.
Item Operation
Sim26-14 PS KIT KEY
PS KIT KEY ON
----------
----------
Sim26-14 PS KIT KEY
PS KIT KEY OK
----------
----------
Sim26-14 PS KIT KEY
PS KIT KEY NG
----------
----------
Sim26-22 LANGUAGE
LANGUAGE 0
(0:JAPANESE
1:ENG.US 2:ENG.UK
1/8 [ 0- 20] 0
Sim26-41 PAMPHLET
AMS MODE SET 0
(0:OFF 1:ON)
[ 0- 1] 0
Display items Content Setting range Default
0:OFF
AMS is not set
automatically.
0-1 0
1:ON
AMS is set automatically.
26-57
Purpose Setting
Function
(Purpose)
Used to set the model code.
Item Operation
Display items Setting range Default
1:AR-265G
1-6 1
2:AR-265FG
3:AR-5127
4:AR:265S
5:AR-265FP
6:AR-M208
43
43-1
Purpose Setting
Function
(Purpose)
Used to set the fusing temperature in each operation
mode.
Section Fixing (Fusing)
Item Operation
(Initial screen) (Input screen)
Display items Content Setting range Default
1:600dpi
600dpi 155-190 185
2:1200dpi
1200dpi 140-190 Disabled
3:POST CARD
Postcard 155-190 185
Sim26-57 MACHINE
MACHINE CODE 1
(1:AR-265G
2:AR-265FG
1/3 [ 1- 6] 1
Sim43-1 FUSER TEMP.
1:600dpi 185
2:1200dpi 160
3:POST CARD 185
2
Sim43-1 FUSER TEMP.
2:1200dpi 160
[140-190] 160