Specifications

AR-FX8 SIMULATIONS, FAX SOFTWARE SWITCH 6-25
TEL/FAX auto
switch
TEL/FAX auto switch setup Initial setup SW 7-1 The line is used either for TEL or FAX.
Voice response send level to the line SW 51-1
Voice response send in TEL/FAX auto switch SW 51-2~3
Number of ring back tone preceding send SW 9-5~8
External
telephone call
Number of calls by external telephone
pseudo-ringing sound
Initial setup SW 9-1~4
Ring back tone ON time SW 10-1~4 External telephone call disable
CNG detection disable
Ring back tone OFF time SW 10-5~8 External telephone call disable
CNG detection disable
Communication General Signal send level SW 15-1~8 When the remote machine does not
receive signals in a proper level.
Polarity reversion monitor in communication SW 23-2 When the line is disconnected during
communication, the communication
report code 2 of 11 or 20 is resulted.
ECM (Other than V.34 mode) Initial setup SW 17-5 Error resend frequently occurs, resulting
in extended communication time.
Timer setup between flag-adrs (V.21-FSK) SW 20-3~4 Communication error in a satellite line
Send/receive coding capacity (Only V.34) SW 17-3~4 Error in JBIG mode
Send/receive coding capacity
(Except for V.34)
SW 17-7~8 Error in JBIG mode
SG3 V.34 mode function SW 43-1 Frequent errors in SG3 communication
V.34 Symbol Rate Mask SW 43-3~6 Frequent errors in SG3 communication
V.34 mode function in manual
communication
SW 42-8 Frequent errors in SG3 communication in
FAX service
Send G3/SG3 Countermeasures against echo in sending SW 20-7 An error occurs in phase B.
DIS reception confirmation SW 20-2 An error occurs in phase B.
CED detection time SW 25-5 CED signal detection error
SG3 V.34 mode send speed SW 44-1~4 An error occurs in SG3 communication.
G3 Echo suppresser tone SW 27-1~4 An error occurs in V.29 communication
Modem send speed SW 16-1~4 To uncertain/certain receiver
DCS-TCF interval time SW 24-1 An error occurs in training.
Error process in RTN reception SW 30-2 OK is displayed when RTN is received.
Receive G3/SG3 CSI send SW 20-1
SG3 V.34 mode reception speed SW 44-5~8 An error occurs in SG3 communication.
G3 Countermeasures against echo in reception SW 20-6 An error occurs n phase B in reception.
Modem speed fixed in reception SW 16-5~6 Fall back or an error occurs due to poor
line conditions.
EOL detection timer SW 23-1 EOL time up occurs frequently.
RTN send line error rate SW 23-7~8 Line error occurs frequently.
EQM judgment in TCF reception
confirmation
SW 24-2 TCF reception error occurs.
TCF reception confirmation judgment
method
SW 24-3 TCF reception error occurs.
Receive print Paper
selection
Sub scan length judgment SW 35-2 Print is not made on the selected paper.
FAX paper exit tray Receive
setup
SW 28-7~8 Print is not made on the selected paper.
Reception data print output condition setup Receive
setup
SW 35-3~4 To make divided print instead of
reduction print.
Auto reduction/Dispose setup Receive
setup
SW 35-7 To disable reduction print.
magnification ratio setup in auto reduction SW 36-1~8 To disable reduction print on fixed size
paper.
Reduction/Dispose setup in printing
A3-11x17
SW 35-8 Print is not made on the selected paper
when A3-11x17 size document is
received.
Duplex reception print Receive
setup
SW 34-8 To make duplex print of received
document
Rotation print SW 35-1 To disable rotation print
Received document output setup in
reception
SW 35-5 To print after reception of each page
Reception width setup of 11 x 17 paper SW 37-3 To print 11x17 document as B4 width
Reception size setup SW 37-1~2 To limit the reception size.
Large item Medium item Content of switch Key operator Soft SW No. Purpose of use
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 25 ページ ２００３年１１月１２日 水曜日 午前９時４５分