Service manual

AR-FX7 SOFT SWITCH 7 - 1
[7] SOFT SWITCH
1. FAX soft switch setting change quick reference table
Large item Middle item Switch content Key operator Soft SW No. Usage
Dialing Remote machine
call disable
Pause time Default setting SW 28-1 – 4 When dialing disable/when error dialing
Dial call signal Default setting SW 22-5, 6 When dialing disable
DTMF-related item None SW 64-4 – 8 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
None SW 65-5 – 8 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
None SW 26-1 – 5 When dialing disable in PBX (private branch
exchange/Fax service, etc.)
Pulse (10PPS) None SW 25-1 – 4 When pulse dialing disable
Signal detection Busy tone detection None SW 21-2 When busy tone detection disable
Busy tone detection None SW 51-1 – 2 When busy tone error is detected
Dial tone detection None SW 21-1
Redial In case of an error Resend interval Transmitter
function setting
SW 14-5 – 8 When send errors occur frequently
In case of an error Number of times of resend Transmitter
function setting
SW 14-1 – 4
When busy Resend interval Transmitter
function setting
SW 13-5 – 8 Whey busy occurs frequently
When busy Number of times of resend Transmitter
function setting
SW 13-1 – 4
Arrival (Call-in) When CI detection
disable
CI detection None SW 86-2, 3 No call-in
CI signal OFF detection time None SW 87-1 – 7 No call-in
External
telephone
Setting of an
external telephone
connected
Yes/No Default setting SW 41-1 When an external telephone is connected
Remote switch
number
Entry of a 2-digit number Default setting SW 7-1 – 8 When remote switch is erroneously detected
Remote switch
setting
Yes/No None SW 6-8 When remote switch is erroneously detected
Communication General Send level None SW 15-4 – 8 When the remote machine cannot receive
signals in a proper level.
JBIG mode None SW 17-4, 8 When an error occurs in the JBIG mode
SG3 V34 mode function setup None SW 43-1 When SG3 communication error occurs
frequently
V34 symbol rate None SW43-4 – 6 When SG3 communication error occurs
frequently
Transmission G3/SG3 DIS reception check One-touch/
Reduction, etc.
SW 69-8 When an error occurs in phase B
Line equalizer None Setting is made referring to the distance from
the station when a communication trouble
occurs.
SG3 V34 send speed One-touch/
Reduction, etc.
When an error occurs in the SG3
communication.
Manual send V34 None SW 42-8 When an error occurs in the SG3
communication in FAX service, etc.
G3 V29 no modulation carrier None When an error occurs in the V29
communication
Modem send speed One-touch/
Reduction, etc.
SW 16-1 – 4 To specified/unspecified destination
RTN reception error None SW 73-1 When judged as “OK” though RTN is received
Reception G3/SG3 CSI transmission None
Maximum reception length None When a document of 1m or longer is received
Proxy reception None
EQM dispersion inhibit None When a lot of errors occur due to the poor
conditions of the line.
SG3 V34 reception speed None When fall-down occurs frequently in the SG3
communication
G3 Countermeasure against
echo in reception
None When an error occurs in phase B in reception
Modem speed in reception None SW 16-5, 6 When the line quality is poor and a fall-back
or an error occurs
EYE-Q check only None SW 72-7 Change in the detection method of training
error