Specifications

AR-FX5 MACHINE OPERATION 7-4
6. Communication report codes
This code is indicated in the column of protocol communication report in
a communication repot table and a communication management table
when communication is terminated.
<1>Communication report code XX (Top 2 digits): 00 ~ 99
<2>Communication report sub code 1: YY: Not used in this machine.
(Always 00)
<3>Communication report sub code 2: ZZ: Indicates details of the report.
A. Communication report code list 1
Means of communication: S = Send, R = Receive, P = Polling, B = Bulletin board
Communication report XX (YY ZZ)
Report code
(Communication
result)
Display in the column of result Content of communication interruption
Means of
communication
0 ~ 31 Refer to the following
descriptions.
Depends on the point of communication interruption. For 16 or later, V.34 mode
communication.
33 BUSY The calling side cannot establish connection with the remote party.
34 CANCEL A communication interruption command is made during sending/receiving.The
interruption key is pressed for interruption of input.
<S/R/P/B>
35 P. FAIL Power is failed during sending/receiving. <S/R/P/B>
36 (No record paper)
37 (Record paper jam)
38 MEM. FULL Memory over during reception.Print is not made during reception in acting
reception inhibit.
<R/P><R/P>
39 (Number of paper unmatched)
40 (Relay not received)
41 LENGTH OVER The send data length of one page exceeds the limit (3m) in sending. <S/B>
42 LENGTH OVER The receive data length of one page exceeds the limit. <R/P>
43 (Communication) (OK) Speaking before data transmission
44 ORIGINAL ERROR A document jam occurs in direct sending. <S>
45 (Picture quality error)
46 NO RESPONSE The FAX signal from the remote party is not detected within T1 time. <S/P>
47 TX DECODE ERROR A decode error occurs in the FAX board. <S/B>
48 OK Normal end of communication Normal end of
communication
49 NO RX POLL The called side does not have polling function in polling reception. The calling
side has no data to send.
<P><P>
50 RX POLL FAIL In polling reception, DCN is received for DTC.In polling sending, there is no send
data.
<P><B>
51 PASS # NG In poling sending, the allow number is not matched. In polling sending, the
system number is not matched.
<B><B>
52 (No confidential function in
remote party)
In confidential sending, the remote party does not have confidential function.
(Including other company's machines)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<S>
53 (Confidential not received) <1>In confidential sending, DCN is received for NSS. <S>
54 (Confidential BOX NO NG) <1>In confidential reception, a confidential box number which is not registered is
specified.
<R>
55 (No relay function in remote
party)
In relay command sending, the remote machine has no relay function.
(Including other company's machine)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<S>
56 NO REL RX <1>In relay command sending, DCN is received for NSS.
<2>In relay command reception, a remote station number which is not registered
is specified.
<3>In F code relay broadcasting, an F code relay command is received.
<S><R><R>
57 (Relay ID unmatched) <1>In relay command reception, the relay ID does not match. <R>
58 (Receive inhibit number) In reception, data are sent from a remote machine of receive inhibit number.
59 RX NO F-CODE POLL In F code polling (calling), the remote machine has no DIS bit 47
(polling function).
<P>
60 NO F-CODE POLL In F code polling (calling), DCN is received for SEP. In bulletin board, there is no
send data for SEP.
<P><B>
61 RX POLL # NG In bulletin board, the sub address (bulletin board number (SEP)) is not matched. <B>