Specifications

AR-FX5 SIMULATIONS, FAX SOFTWARE SWITCH 6-38
44 1-4 V.34 mode transmission
speed
Used to set the communication speed (capacity) when transmitting in V.34 mode.
The set range is 2400bps - 33600bps in the increment of 2400bps by binary input
of N into "2400(bps) x N."When N is set to 0000, it is set to 2400bps. When set to
1111, it is set to 33600bps.When, however, set to 2400bps, SW45-1~6 must be
disabled. When set to 33600bps, SW45-7 must be enabled "1". This switch sets
only the capacity and communication is not always performed at the set speed.
1 33600bps
1
1
0
5-8 V.34 mode reception
speed
Used to set the communication speed (capacity) when receiving in V.34 mode.
The set range is 2400bps - 33600bps in the increment of 2400bps by binary input
of N into "2400(bps) x N."When N is set to 0000, it is set to 2400bps. When set to
1111, it is set to 33600bps.When set to 2400bps, however, SW43-3~6 must be set
to 2400: "0000."
When set to 33600bps, SW43-3~6 must be set to 3429: "0101."
This switch sets only the capacity and communication is not always performed at
the set speed.
1 33600bps
1
1
0
45 1 2800 Symbol Rate Mask
in V.34 communication
Used to set Enable/Disable of 2800Hz as Symbol Rate of V.34.
When set to Disable, 2800Hz is not selected.
0 Enable
2 Not used 0
3 3000 Symbol Rate Low
Carrier setup in V.34
transmission
Used to set Enable/Disable of Low/High carrier when selecting 3000Hz as Symbol
Rate of V.34.When this is set to Disable, Low of 3000Hz is not selected. It is valid
only in transmission.
0 Enable
4 3000 Symbol Rate High
Carrier setup in V.34
transmission
Used to set Enable/Disable of Low/High carrier when selecting 3000Hz as Symbol
Rate of V.34. When this is set to Disable, High of 3000Hz is not selected. It is valid
only in transmission.When both of Low/High are set to Disable, Symbol
Rate=3000Hz is not selected.
0 Enable
5 3200 Symbol Rate Low
Carrier setup in V.34
mode
Used to set Enable/Disable of Low/High carrier when selecting 3000Hz as Symbol
Rate of V.34. When this is set to Disable, Low of 3200Hz is not selected. It is valid
only in transmission.
0 Enable
6 3200 Symbol Rate High
Carrier setup in V.34
transmission
Used to set Enable/Disable of Low/High carrier when selecting 3000Hz as Symbol
Rate of V.34. When this is set to Disable, High of 3200Hz is not selected. It is valid
only in transmission.When both of Low/High are set to Disable, Symbol
Rate=3200Hz is not selected.
0 Enable
7 3429 Symbol Rate Mask
in V.34 transmission
Used to set whether 3429Hz is used as Symbol Rate of V.34 or not.
When set to Disable, 3429Hz is not selected. Valid only in transmission.
0 Enable
8 Not used 0
46 1 Primary channel return
mode setup
Used to set the next state after completion of primary channel phase. 1 PPh signal
2-6 Not used 0
0
0
0
0
7,8 V.8 mode ANSam signal
send time
Used to set ANSam signal send time when sending ANSam signal in V.8 mode. 0 4sec
1
SW
No.
Bit
No.
Item Switch selection and function Initial value
Key
operator
1: Disable 0: Enable
1: Disable 0: Enable
1: Disable 0: Enable
1: Disable 0: Enable
1: Disable 0: Enable
1: Disable 0: Enable
1: PPh signal send sequence 0: Sh signal send sequence
Bit No. 7 8
3sec 0 0
4sec 0 1
5sec 1 0
6sec 1 1