Service manual

AR-235/275 SIMULATION - 29
When initializing each data: 50
Note: Executable only when the FAX is installed.
Operation/procedure
The FAX exposure level can be adjusted separately for each mode by
specifying a sub code. Since selection of Auto/Manual and Photo ON/
OFF is allowed separately for each mode, adjustments of 14 patterns
in total can be made.
(Refer to 46-12, "Exposure adjustment table".)
Shading is performed to turn on the copy LED.
The current exposure value of the selected mode is displayed.
Enter the 2-digit adjustment value with the 10-key pad and push
START key. The entered value is set for the specified mode, and the
self print is made with the same magnification ratio for the mode.
Note: Executable only when the FAX is installed.
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
(Auto adjustment)
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTER-
RUPT] key is inhibited.
Operation/procedure (Pattern 2)
Select the mode with the 10-key and press the [OK] key.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
Auto exposure mode
• When SIM 26-6 (Destination setup) is changed from EX to Japan,
the setup value becomes 1 (Default: Japan). If, on the contrary, it is
changed from Japan to EX, the set value becomes 2 (Default: EX)
• If the auto exposure mode setup value is changed, the setup value
of SIM 46-30 (AE limit setup) is reset to the default value.
Operation/procedure (Pattern 2)
Select the mode with the 10-key and press the [OK] key.
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Pressing the [BACK] key returns to the mode selection.
Mode AE Photo Exposure adjustment
STD
(Standard
character)
Auto
ON –
Manual
Auto
OFF
Individual adjustment
enable
(46-13 to 16)
Manual
Fine
(Small
character)
Auto
ON
Manual
Auto
OFF
Manual
S-fine
(Fine)
Auto
ON
Manual
Auto
OFF
Manual
U-fine
(Super fine)
Auto
ON
Manual
Auto
OFF
Manual
46-13 to 16
Purpose
Adjustment
Function
(Purpose)
FAX exposure level adjustment (individual)
Sub code Mode
13 STD (normal character)
14 Fine (small character)
15 S-fine (super fine)
16 U-fine (super fine)
46-18
Purpose
Adjustment
Function
(Purpose)
Used to adjust the copy contrast. (Inclination)
Item
Picture quality
(Initial screen) (Input screen) (Executing screen)
Sim46-18 GAMMA SET.
1:AE 50
2:TEXT 50
3:TEXT/PHOTO 50
1/3 50
Display items Content
Setting
range
Default
1:AE
AE 1-99 50
2:TEXT
Character Level 3.0
3:TEXT/PHOTO
Character/Photo Level 3.0
4:PHOTO
Photo Level 3.0
5:SUPER PHOTO
Super photo Level 3.0
6:AE(TS)
AE(TS)
7:TEXT(TS)
Character (TS) Level 3.0
8:TEXT/PHOTO(TS)
Character/Photo (TS) Level 3.0
46-19
Purpose
Adjustment
Function
(Purpose)
Used to change the image quality in the exposure
mode.
Item
Picture quality
(Initial screen) (Input screen)
Display items Content Default
1:AE MODE
(1:EXPOSURE
2:TONER)
Auto exposure mode
(1: Priority on Image quality,
2: Priority on toner consumption)
2
2:AE STOP(COPY)
(0:FIXED
1:REAL TIME)
Auto exposure STOP mode (COPY)
(0: Fixed, 1: Real-time)
0
3:AE STOP(FAX)
(0:FIXED
1:REAL TIME)
Auto exposure STOP mode (FAX)
(0: Fixed, 1: Real-time)
0
4:AE STOP(SCAN)
(0:FIXED
1:REAL TIME)
Auto exposure STOP mode
(SCANNER)
(0: Fixed, 1: Real-time)
0
5:1200dpi PHOTO
(1:SOFT
2:HARD)
1200dpi photo mode
(Countermeasures for claims on
dither)
(1: Soft mode, 2: Hard mode)
1
46-20
Purpose
Adjustment
Function
(Purpose)
Used to correct SPF exprosure.
Item
Picture quality
Sim46-19 AE MODE
1:AE MODE 1
2:AE STOP(COPY) 0
3:AE STOP(FAX) 0
1/2 1
Sim46-19 AE MODE
1:AE MODE 1
(1:EXPOSURE
2:TONER)
[ 1- 2] 1