Service manual

AR-235/275 SIMULATION - 22
Operation/procedure (Pattern 1)
Used to set whether the trouble history of SIM 22-4 is displayed as
one-time trouble or as a number of times of troubles continuously
occurred when two or more troubles of the same kind occurred.
Enter the set value with 10-key, and press [OK] key.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only with SRU (AR models).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only with CRU (DM models).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only with CRU (DM models).
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Note: Executable only when the finisher is installed.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key.
Operation/procedure (Pattern 1)
Input the set value with the 10-key and press the [OK] key, and the
LCD contrast will be immediately changed and displayed.
Display items Setting range
Default
Japan, SEC, SECL,
SCA, SEF, Taiwan
Others
0:OFF
0-1 0 1
1:ON
26-35
Purpose
Setup
Function
(Purpose)
Used to set the mode of trouble memory.
Item
Specifications
Display item Content Set range Default
0:ONCE
When two or more troubles
occur, only one is registered.
0-1 0
1:ANY
All the troubles occurred are
registered.
26-36
Purpose
Setting
Function
(Purpose)
Used to set whether to stop when the maintenance life
is reached.
Item
Operation
Display items Content Setting range Default
0:STOP
Stop 0-1 1
1:NON STOP
Non stop
26-37
Purpose
Setting
Function
(Purpose)
Used to set whether to stop when the developer life is
reached.
Item
Operation
Display items Content Setting range Default
0:STOP
Stop 0-1 0
1:NON STOP
Non stop
Sim26-35 TROUBLE
TROUBLE MODE 0
(0:ONCE 1:ANY)
[ 0- 1] 0
Sim26-36 MAINTESTOP
MAINTENANCE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1] 0
Sim26-37 DEVE. STOP
DEVE. LIFE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1] 0
26-38
Purpose
Setting
Function
(Purpose)
Used to set whether to stop when the drum life is
reached.
Item
Operation
Display items Content Setting range Default
0:STOP
Stop 0-1 0
1:NON STOP
Non stop
26-46
Purpose
Setting
Function
(Purpose)
Used to set whether to meet with the output direction of
images regardless of the mode when installing the
finisher.
Item
Operation
Display items Content Setting range Default
0:OFF
Setting No 0-1 0
1:ON
Setting Yes
26-50
Purpose
Setting
Function
(Purpose)
Used to set whether to use the black/white reverse
function.
Item
Operation
Display
items
Content
Setting
range
Default
0:ON
Enable 0-1 0
1:OFF
Disable
26-54
Purpose
Setting
Function
(Purpose)
Used to set the PWM duty (brightness) at the center
value of the LCD contrast.
Item
Operation
Setting range 30-70
Default 50
Sim26-38 DRUM STOP
DRUM LIFE OVER 0
(0:STOP
1:NON STOP)
[ 0- 1] 0
Sim26-46 OUT DIR
OUT DIRECTION 0
(0:OFF 1:ON)
[ 0- 1] 0
Sim26-50 B/W REV.
B/W REVERSE 0
(0:ON 1:OFF)
[ 0- 1] 0
Sim26-54 LCD DUTY
LCD PWM DUTY 0
[ 30- 70] 0