Specifications

AR-FX11 SIMULATIONS, FAX SOFTWARE SWITCH 6-22
5. FAX software switch
A. Software switch setup change quick reference
Large item Medium item Content of switch Key operator Soft SW No. Purpose of use
Dial (Calling) Remote
machine
calling disable
Polarity inversion monitor during call-out - SW 23-3 Dial disable
Pause time setting Inital setup SW 28-1~4 Dial disable/Erroneous dialing
Tone/pulse default setting - SW 22-5,6 Dial disable
DTMF signal send time - SW 26-1~5 Dial disable in PB(PB/FAX service,etc.)
DTMF send MAX. level - SW 65-1~4 Dial disable in PB(PB/FAX service,etc.)
DTMF send level (High area) - SW 64-4~8 Dial disable in PB(PB/FAX service,etc.)
DTMF send level(Difference between high
area and low area)
- SW 65-5~8 Dial disable in PB(PB/FAX service,etc.)
Minimum pause time (DTMF) setting - SW 26-6~8 Dial disable in PB(PB/FAX service,etc.)
Scanner scanning completion speaker sound
volume
- SW 46-1,2
Scanning sound volume pattern number - SW 46-3~8
Minimum pause time (10PPS) setting - SW 19-1~4 Dial disable in pulse
Minimum pause time (20PPS) setting - SW 19-6~8 Dial disable in pulse
Signal
detection
Dial tone detection - SW 21-1 Dial tone detection disable
Busy tone detection - SW 21-2 Busy tone detection disable
Redial Error Number of resends in a communication error Send setup SW 14-1~4
Error Resend interval in a communication error - SW 14-5~8
Error(SG3) Resend in case of an error, Super G3 disable
in the last call out
- SW 43-2
Busy Number of recalls when busy Send setup SW 13-1~4
Busy Resend interval when busy - SW 13-5~8
Reception(Callin
g)
CI detection
disable
CI detection - SW 86-2,3
Not used - SW 86-6~8
CI signal OFF detection enable time - SW 87-1~7
F-net 1300Hz detection - SW 51-6
1300 Hz detection time - SW 51-7
External
telephone
handset
External
telephone
connection
External telephone connection Inital setup SW 41-1 External telephone connection
Remote switch number setting - SW 7-1~8 Remote switch detection error
TEL/FAX auto
switch
CNG detection time - SW 21-5~8
External
telephone call
Ring back tone ON time - SW 57-1~4 External telephone call disable CNG
detection disable
Ring back tone OFF time - SW 57-5~8 External telephone call disable CNG
detection disable
Communication General Signal send level - SW 15-4~8 When the remote machine does not
receive signals in a proper level
Polarity inversion monitor during
communication
- SW 23-2
SG3 V.34 mode function - SW 43-1 Frequent errors in SG3 communication
Symbol speed mask in V.34 receive - SW 43-4~6 Frequent errors in SG3 communication
Send G3/SG3 Countermeasures against echo in send (The
hold time until signal send is set after DIS
receive.)
- SW69-8 An error occurs in phase B
G3 Error process in RTN receive - SW73-1 OK is displayed when RTN is received
Receive G3/SG3 CSI send - SW70-2
Max. length of receive - SW69-4
Substitute receive - SW9-1
SG3 Countermeasures against echo in receive
(CED tone send interval)
- SW69-7 An error occurs in phase B in reception
Modem speed fixed in receive - SW16-5,6
EYE-Q check - SW72-7
Receive print Paper
selection
Paper selection priority order - SW35-2
Output condition setting Receive
setup
SW35-3,4
Automatic reduction print - SW35-1
Automatic reduction magnification ratio - SW 35-5~8
Rotation print - SW40-1 To disable rotation print
[06]SIMULATIONS ･ FAXSOFTWARESWITCH.fm 22 ページ ２００４年１１月１２日 金曜日 午後２時２４分