- Digital Copying Machine - Operation Manual

ManualsBrandsSharp ManualsAll in One PrinterAR-275

• GETTING STARTED

• MAKING COPIES

• SPECIAL FUNCTIONS

• COPIER TROUBLE?

• GENERAL INFORMATION

• OPTIONAL EQUIPMENT

DIGITAL COPYING MACHINE

OPERATION MANUAL

Page

MODEL

AR-235

AR-275

Summary of content (130 pages)

PAGE 1
MODEL AR-235 AR-275 DIGITAL COPYING MACHINE OPERATION MANUAL Page • GETTING STARTED • MAKING COPIES • SPECIAL FUNCTIONS • COPIER TROUBLE? • GENERAL INFORMATION • OPTIONAL EQUIPMENT 5 23 41 65 77 91
PAGE 2
➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣ FOR YOUR RECORDS ... To protect against loss or theft, record and retain for reference the copier’s serial number located on the back of the unit.
PAGE 3
00.book 1 ページ２００１年４月２０日金曜日午後９時３４分 OUTLINE OF THIS MANUAL 1. GETTING STARTED This chapter describes the basic information on the use of this copier. 2. MAKING COPIES This chapter describes the basic copying functions such as normal copying, reduction or enlargement, and exposure adjustments. 3. 4 GENERAL INFORMATION This chapter describes general information about the use of the copier and the loading of paper and toner. 6.
PAGE 4
00.book 2 ページ２００１年４月２０日金曜日午後９時３４分 CONTENTS Page CHAPTER 1 GETTING STARTED INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 COPIER INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PART NAMES AND FUNCTIONS . . .
PAGE 5
00.book 3 ページ２００１年４月２０日金曜日午後９時３４分 CONTENTS Page CHAPTER 4 COPIER TROUBLE? STATUS MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . MISFEED REMOVAL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Misfeed in the bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Misfeed in the copier. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Misfeed in the center tray . . . . . . . . . . .
PAGE 6
00.
PAGE 7
00.book 5 ページ２００１年４月２０日金曜日午後９時３４分 1 CHAPTER 1 GETTING STARTED This chapter describes the basic information on the use of this copier. Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 ● CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ● COPIER INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 ● MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
00.book 6 ページ２００１年４月２０日金曜日午後９時３４分 INTRODUCTION This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarize yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. NOTES: copier can be used as a laser printer, a facsimile machine, and a scanner by installing optional components.
PAGE 9
00.book 7 ページ２００１年４月２０日金曜日午後９時３４分 CAUTIONS Follow the cautions below when using this copier. WARNING: fusing area is hot. Exercise care in this area when removing misfed paper. ● Do not look directly at the light source. Doing so may damage your eyes. 1 ● The CAUTION: socket-outlet should be installed near the equipment and shall be easily accessible. ● Place the copier on a firm, level surface. ● Do not install the copier in a humid or dusty location.
PAGE 10
00.book 8 ページ２００１年４月２０日金曜日午後９時３４分 COPIER INSTALLATION Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. CAUTION: If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
PAGE 11
00.book 9 ページ２００１年４月２０日金曜日午後９時３４分 COPIER INSTALLATION Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements (See page 89.). Also make certain the outlet is properly grounded. NOTE: Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker. 12" (30 cm) A small amount of ozone is produced within the copier during operation.
PAGE 12
00.book 10 ページ２００１年４月２０日金曜日午後９時３４分 MAIN FEATURES 1 High-speed laser copying ● ● GETTING STARTED 2 High-quality digital image ● ● ● 3 First-copy time at 600 dpi (not in the super photo mode) is only 4.8 seconds (except when recovering from a power save mode or immediately after power on). Copying speed is 23 copies/min. (AR-235) or 27 copies/min. (AR-275) at 600 dpi (not in the super photo mode), which lends itself for business use, providing improvement in working efficiency.
PAGE 13
00.book 11 ページ２００１年４月２０日金曜日午後９時３４分 MAIN FEATURES 4 ● 1 Optional features ● ● ● ● ● ● 6 The copier is equipped with a memory buffer allowing the copier to scan an original once and make up to 999 copies of the scanned image. This improves workflow, reduces operating noise from the copier and reduces wear and tear on the scanning mechanism, which provides for a higher reliability. An optional single pass feeder (SPF) allows automatic document feeding of up to 30 sheets of single-sided originals.
PAGE 14
PART NAMES AND FUNCTIONS Exterior GETTING STARTED 12
PAGE 15
PART NAMES AND FUNCTIONS Interior 1 GETTING STARTED 13
PAGE 16
00.book 14 ページ２００１年４月２０日金曜日午後９時３４分 PART NAMES AND FUNCTIONS Operation panel GETTING STARTED COPY key and indicator (p. 76, 84) Press to select the COPY mode. Press and hold during standby or during warmup to display the total output count and the quantity of toner remaining. Numeric keys Use to select the desired copy quantity. Mode keys and indicators Use these keys when relevant components are installed. CLEAR ALL key (p.
PAGE 17
PART NAMES AND FUNCTIONS 1 GETTING STARTED 15
PAGE 18
POWER ON AND OFF The power switch is located on the left side of the copier. Power on Turn the power switch to the "ON" position. Power on GETTING STARTED ● When the power switch is turned to the "ON" position, the message "System check." will appear in the message display and warm-up will srart. During warm-up, you can select your desired job settings and then by pressing the START key, your job will commence when the copier comes to "Ready to copy.
PAGE 19
00.book 17 ページ２００１年４月２０日金曜日午後９時３４分 POWER ON AND OFF Initial settings The copier assumes the initial settings when it is first turned on, when the CLEAR ALL key is pressed, or a preset time (auto clear time) after the last copy is made in any mode. The initial settings that appear in the display are shown below. Ready to copy. 1 81/2 11 100% 81/2 11 AUTO ● Copy ratio: 100% Automatic ● Auto paper selection: On.
PAGE 20
00.book 18 ページ２００１年４月２０日金曜日午後９時３４分 FUNCTION ICONS The following function icons will be indicated on the setting screen of each copier function.
PAGE 21
00.book 19 ページ２００１年４月２０日金曜日午後９時３４分 FUNCTION REVIEW The current settings of copier functions that have been selected can be viewed in the display. ● The XY ZOOM and TRANSPARENCY functions cannot be viewed on the function review screen. 1 1 Press the JOB STATUS key. ● The review screen will appear. GETTING STARTED FUNCTION REVIEW 2in1 PATTERN1 NO 2 Use the and keys to select a function. ● The setting for the selected function will appear in the display.
PAGE 22
AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not perform copier functions until an assigned 5-digit account number has been entered. ★ KEY OPERATOR See page 21 of the KEY OPERATOR'S GUIDE for setting the auditing mode. How to copy in the auditing mode GETTING STARTED If the copier has been programmed in the auditing mode, the following message will appear in the display in place of the normal initial conditions display. Enter your account number.
PAGE 23
00.book 21 ページ２００１年４月２０日金曜日午後９時３４分 AUDITING ACCOUNTS 2 When copying is completed, press the AUDIT CLEAR key. 1 Please see your key operator for assistance. ★ KEY OPERATOR security. See page 24 of the KEY OPERATOR'S GUIDE for account number 21 GETTING STARTED NOTE: If an unassigned number is entered, "Enter your account number." will appear again in the display, indicating that the number was not accepted.
PAGE 24
01d.
PAGE 25
00.book 23 ページ２００１年４月２０日金曜日午後９時３４分 CHAPTER 2 2 MAKING COPIES This chapter describes the basic copying functions such as normal copying, reduction or enlargement, and exposure adjustments. Page COPYING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 ● TWO-SIDED COPYING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Two-sided copying from the platen glass. . . . . . . . . . . . . . . . . . . . 26 ● EXPOSURE ADJUSTMENT . . . . . . . . . . . . . . . . . .
PAGE 26
00.book 24 ページ２００１年４月２０日金曜日午後９時３４分 NORMAL COPYING The basic copying procedure is described below. ● Image loss (max. 5/32" (4 mm)) can occur at the leading and trailing edges of the copies. Also image loss (max. 1/8" (3 mm)) can occur along the other edges of the copies. NOTE: If the copier has been programmed in the auditing mode, enter a 5-digit account number. See page 20. 1 Place an original face down on the platen glass and align it with the original size scale.
PAGE 27
NORMAL COPYING 3 Ensure that the desired paper tray is selected. Ready to copy. 81/2 11 AUTO 100% 81/2 11 4 AUTO Set the number of copies using the numeric keys. MAKING COPIES ●A 2 single copy can be made even when "0" is displayed. the CLEAR key to clear an entry if a mistake is made. ● Press 5 Press the START key. ● The number in the copy quantity display will decrease by 1 each time a copy is made.
PAGE 28
TWO-SIDED COPYING Two-sided copies can be made by manually placing originals on the platen glass as described in the procedure below. Fully automatic two-sided copies can be made from one-sided originals if either an optional single pass feeder (SPF) or an optional reversing single pass feeder (RSPF) is installed. See page 95. Additionally, fully automatic two-sided copying of two-sided originals or one-sided copying of two-sided originals can be made if an optional RSPF is installed. See page 98.
PAGE 29
TWO-SIDED COPYING 3 Use the 4 Use the OK key. 5 Ensure that the desired paper tray is selected. 6 Set the number of copies and press the START key. ● Also and keys to select one-sided to two-sided copying. the 2-SIDED COPY key can be used to select a duplex copy mode. or key to select binding change if desired.
PAGE 30
00.book 28 ページ２００１年４月２０日金曜日午後９時３４分 TWO-SIDED COPYING 7 Place the second original face down on the platen glass and press the START key again. ● To stop a copy run during duplex copying, press the CLEAR key. cancel the duplex copy mode, press the 2-SIDED COPY key, select the one-sided to one-sided mode, and press the OK key. ● If an uneven number of originals are being copied, press the READ-END key after the last original is scanned. The last copy will be output single-sided.
PAGE 31
00.book 29 ページ２００１年４月２０日金曜日午後９時３４分 EXPOSURE ADJUSTMENT This copier has five exposure modes to choose from: AUTO, TEXT, TEXT/PHOTO, PHOTO, and SUPER PHOTO. Auto This is the standard initial setting for this copier. In this mode, the characteristics of an original being copied are "read" by the exposure system, and exposure adjustments are made automatically. This optimizes the contrast of the copied images by reducing the effect of colored or shaded background areas.
PAGE 32
00.book 30 ページ２００１年４月２０日金曜日午後９時３４分 EXPOSURE ADJUSTMENT 3 Use the ● Copy and keys to adjust the copy density as desired. density cannot be adjusted manually in the AUTO exposure mode. EXPOSURE AUTO AUTO TEXT TEXT/PHOTO 4 Press the OK key. MAKING COPIES ● To return to the AUTO mode, press the EXPOSURE key, use the "AUTO", and press the OK key.
PAGE 33
00.book 31 ページ２００１年４月２０日金曜日午後９時３４分 REDUCTION/ ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the COPY RATIO key. The zoom function enables precise copy ratio selection from 25% to 400% in 1% increments.
PAGE 34
00.book 32 ページ２００１年４月２０日金曜日午後９時３４分 REDUCTION/ENLARGEMENT/ZOOM 3 Press the AUTO IMAGE key. ● The copy ratio will be automatically set. the original and the selected copy paper are not in the same orientation, the image will be automatically rotated to match the copy paper. However, if enlargement is selected for copying onto a paper size larger than 8-1/2" x 11" (A4), the image will not be rotated. In this case a message indicating "Image edge loss" will appear.
PAGE 35
00.book 33 ページ２００１年４月２０日金曜日午後９時３４分 REDUCTION/ENLARGEMENT/ZOOM Manual selection 1 Place an original on the platen glass and close the platen cover. 2 2 Press the COPY RATIO key. ● The copy ratio adjustment screen will appear. 3 MAKING COPIES COPY RATIO 121% 100% 95% ZOOM 100% AUTO Use the and keys to select a preset copy ratio or use the keys to select a zoom ratio. and A. Preset reduction ratios are: 95%, 77%, 64%, 50%, and 25%. B.
PAGE 36
00.book 34 ページ２００１年４月２０日金曜日午後９時３４分 REDUCTION/ENLARGEMENT/ZOOM 4 Press the OK key. ● The MAKING COPIES 34 display will return to the basic screen. 5 Ensure that the desired paper tray is selected. 6 Set the number of copies and press the START key. ● If the auto paper select function has been enabled, the appropriate copy paper size will have been automatically selected based on the original size and the selected copy ratio.
PAGE 37
00.book 35 ページ２００１年４月２０日金曜日午後９時３４分 ROTATION COPYING If rotation of original image is enabled using a key operator program, the image of the original will rotate when the orientation of the original does not match that of the copy paper. Rotation copying will function only if the auto paper select mode or the auto image mode has been selected. Even if rotation of original image is disabled using a key operator program, rotation copying will function when the 2 in 1 or 4 in 1 function is selected.
PAGE 38
00.book 36 ページ２００１年４月２０日金曜日午後９時３４分 BYPASS FEED (special paper) The bypass tray must be used to feed special papers such as transparency film and labels but can also be used to feed standard copy paper. Acceptable paper for copying from the bypass tray MAKING COPIES Size Weight Capacity (21 lb. bond paper) Special paper Ordinary paper: 5-1/2" x 8-1/2" to 11" x 17" 14 lbs. to 34 lbs.
PAGE 39
00.book 37 ページ２００１年４月２０日金曜日午後９時３４分 BYPASS FEED (special paper) 2 Set the paper guides to the copy paper width. 3 Insert the copy paper (print face down) all the way into the bypass tray. the number of sheets which can be loaded into the tray, see the previous page. adding paper, first remove any paper remaining in the tray, combine it with the paper to be added and then reload as a single stack. The paper to be added must be the same size and type as the paper already in the tray.
PAGE 40
00.book 38 ページ２００１年４月２０日金曜日午後９時３４分 BYPASS FEED (special paper) 5 Set the number of copies and press the START key. NOTE: The bypass tray can be used to copy onto the two sides of paper manually. When copying the second original, be sure to turn over the copy of the first original left to right and place it into the bypass tray as shown in the illustration.
PAGE 41
00.book 39 ページ２００１年４月２０日金曜日午後９時３４分 INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. ● Two-sided and 2 in 1/ 4 in 1 copying jobs cannot be interrupted. ● Two-sided copying, sort, group, staple sort, job programs and 2 in 1/ 4 in 1 cannot be selected for interrupt copying. Key operator programs cannot be used in the interrupt mode. 1 Press the INTERRUPT key.
PAGE 42
00.book 40 ページ２００１年４月２０日金曜日午後９時３４分 INTERRUPTING A COPY RUN 5 When all INTERRUPT copies are finished, press the INTERRUPT key again to cancel the INTERRUPT mode, and remove the original used for interrupt copying. ● All 6 MAKING COPIES 40 settings for the interrupted job will be automatically restored. Replace the original(s) for the interrupted job and press the START key to resume copying.
PAGE 43
00.book 41 ページ２００１年４月２０日金曜日午後９時３４分 CHAPTER 3 SPECIAL FUNCTIONS This chapter describes special copying functions including various image editing functions. Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Copying in the sort or group mode. . . . . . . . . . . . . . . . . . . . . . . . . 42 ● MARGIN SHIFT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 ● ERASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 44
00.book 42 ページ２００１年４月２０日金曜日午後９時３４分 SORT/GROUP The copier has two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. Sort mode Sets of copies will be sequentially delivered to the center tray. 1 2 3 3 1 2 3 2 1 1 2 3 Group mode Multiple copies of each original will be grouped in the center tray.
PAGE 45
00.book 43 ページ２００１年４月２０日金曜日午後９時３４分 SORT/GROUP 2 Press the OUTPUT key. ● The output mode selection screen will appear. SORT NO SORT 12 3 SORT 111 GROUP 3 Use the OK key. ● Also and keys to select the desired output mode and press the the OUTPUT key can be used to select an output mode. 3 SPECIAL FUNCTIONS 4 Make all other desired copier selections and press the START key. ● If originals have been set in an optional SPF or RSPF in step 1, copying will start.
PAGE 46
00.book 44 ページ２００１年４月２０日金曜日午後９時３４分 SORT/GROUP 6 After all originals have been scanned, press the READ-END key. ● Copying will start. the memory becomes full of scanned original image data, a warning message will appear. Press the START key to start copying the data in memory or the CLEAR ALL key to cancel copying. ● The memory can be extended to a maximum of 272 MB to increase the capacity for storing image data by adding commercially available memory modules.
PAGE 47
MARGIN SHIFT The MARGIN SHIFT feature, in its initial setting, automatically shifts the text or image to increase the margin by approximately 1/2". Original Increased Copy margin A A Original A Copy A Increased margin Original Copy A A Increased margin ● The location of the margin to be increased can be selected at the left edge, the right edge or the top edge of the page. To select the location, see step 4 overleaf.
PAGE 48
00.book 46 ページ２００１年４月２０日金曜日午後９時３４分 MARGIN SHIFT 3 Press the OK key. ● The setting screen for MARGIN SHIFT will appear. MARGIN SHIFT OFF DOWN RIGHT ----1/2 inch(1/4~1) 4 Use the and keys to select the shift direction and the to select the shift amount. ● Select ● Select SPECIAL FUNCTIONS 5 the shift direction from DOWN, RIGHT, and LEFT. the shift amount from 1/4", 1/2", 3/4", and 1". display will return to the basic screen. Make all other desired copier selections and press the START key .
PAGE 49
00.book 47 ページ２００１年４月２０日金曜日午後９時３４分 ERASE This copier has an edge erase mode and a center erase mode. Center erase Edge erase AB A A Edge + Center erase AB AB AB ● Edge erase can be used to eliminate shadow lines around the edges of copies which appear when thick paper or a book is used as an original. ● Center erase can be used to eliminate the shadow produced by the bindings of bound documents. ● Edge + center erase can be used together to eliminate both types of shadow lines.
PAGE 50
ERASE 4 Use the 5 Use the 6 Press the OK key. ● Select SPECIAL FUNCTIONS ● The 7 keys to select the desired erase mode. "EDGE", "CENTER" or "EDGE + CENTER". and keys to adjust the amount of erase if needed. display will return to the basic screen. Make all other desired copier selections and press the START key .
PAGE 51
00.book 49 ページ２００１年４月２０日金曜日午後９時３４分 DUAL PAGE COPY The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the platen glass. It is especially useful when copying books and other bound documents. Original Copy ● This feature can be used in the one-sided to two-sided copying mode. feature cannot be used with the 2 in 1 / 4 in 1, center erase, edge + center erase, enlargement or staple sort features.
PAGE 52
DUAL PAGE COPY 3 Use the key. and keys to select "DUAL PAGE COPY" and press the OK ●A check mark will appear to the left of "DUAL PAGE COPY", and the display will return to the basic screen. 4 5 SPECIAL FUNCTIONS 50 Check to be sure that 8-1/2" x 11" sized copy paper is selected. ● 8-1/2" x 11"R paper can also be used if the auto paper select mode is selected and rotation copying has been enabled.
PAGE 53
00.book 51 ページ２００１年４月２０日金曜日午後９時３４分 2 IN 1 OR 4 IN 1 The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a specified order, onto one sheet. 2 in 1 copying Pattern Pattern Pattern Pattern Pattern Pattern Pattern 4 in 1 copying Pattern ● These features cannot be used with the dual page copying, XY zoom, erase or margin shift features. ● Copies can be made with or without the border lines. ● The order of originals which will be arranged on the copies can be selected.
PAGE 54
2 IN 1 OR 4 IN 1 3 Press the SPECIAL FUNCTION key. Then press the OK key. ● The SPECIAL MODES screen will appear. SPECIAL MODES MARGIN SHIFT ERASE DUAL PAGE COPY [OK]:ADJUST 4 Use the ● The and keys to select "2in1/4in1" and press the OK key. selection screen for 2 in 1 / 4 in 1 will appear. 2in1/4in1 OFF 2in1 4in1 [OK]:CHANGE----SPECIAL FUNCTIONS 52 5 Use the 6 Use the ● The and keys to select "2in1" or "4in1" and press the OK key. setting screen for 2 in 1 or 4 in 1 will appear.
PAGE 55
00.book 53 ページ２００１年４月２０日金曜日午後９時３４分 2 IN 1 OR 4 IN 1 7 Use the ● Select and keys to select a type of border line. the solid line, broken line or no border line. 2in1 PATTERN 1 BORDER 8 Press the OK key. 3 ● The Make all other desired copier selections and press the START key . ● The copy ratio will be calculated automatically. an optional SPF or RSPF is used, copying will start after originals are scanned. ● If the platen glass is used, proceed to the next step.
PAGE 56
B/W REVERSE The B/W REVERSE feature is used to reverse black and white areas. Original Copy ● When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the TEXT mode. Other exposure modes cannot be selected. Even if this feature is canceled, the TEXT mode will not automatically be canceled. 1 Place an original on the platen glass or in the document feeder tray. Document feeder tray 2 Press the SPECIAL FUNCTION key. Then press the OK key.
PAGE 57
00.book 55 ページ２００１年４月２０日金曜日午後９時３４分 B/W REVERSE 4 Make all other desired copier selections and press the START key . ● To cancel the B/W reverse feature, highlight "B/W REVERSE" with a check mark on the SPECIAL MODES screen and press the OK key.
PAGE 58
00.book 56 ページ２００１年４月２０日金曜日午後９時３４分 XY ZOOM The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. Example: Reduction only in the horizontal direction Original Copy ● This feature cannot be used with the 2 in 1 or 4 in 1 feature. use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.) ● The copy ratios can be set from 25% to 400%.
PAGE 59
00.book 57 ページ２００１年４月２０日金曜日午後９時３４分 XY ZOOM 3 Use the and keys to select "XY ZOOM" and press the OK key. ● The setting screen for XY ZOOM will appear. The copy ratio in the horizontal direction will be highlighted. XY ZOOM 121% ZOOM 100% X: 100% 95% Y: 100% [ ]:X Y 4 Use the , , direction. , and keys to change the copy ratio in the horizontal 3 the and keys to set the approximate ratio, then press the ratio or key to increase the ratio. 5 Press the ● The key to decrease the key.
PAGE 60
00.book 58 ページ２００１年４月２０日金曜日午後９時３４分 XY ZOOM 7 Press the OK key. ● The display will return to the basic screen. Ready to copy. 81/2 11R X121% Y 99% 81/2 14 8 Ensure that the desired paper tray is selected. 9 Make all other desired copier selections and press the START key . ● If the auto paper select function has been enabled, the appropriate copy paper size will have been automatically selected based on the original size and the selected copy ratios. Image rotation may occur.
PAGE 61
00.book 59 ページ２００１年４月２０日金曜日午後９時３４分 TRANSPARENCY The TRANSPARENCY feature is used to copy onto transparency film. ● When copying onto transparency film, use this feature to obtain better copy quality. When this feature is selected, the bypass tray will be automatically selected and "TRANSPARENCY" will appear in the paper size display. ● This feature cannot be used with duplex copying or staple sort copying. ● Recommended transparency film is SF-85A.
PAGE 62
TRANSPARENCY 4 Load transparency film into the bypass tray. 5 Make all other desired copier selections and press the START key . ● Load ● To transparency film one sheet at a time in the portrait orientation. cancel the transparency feature, highlight "TRANSPARENCY" with a check mark on the SPECIAL MODES screen and press the OK key.
PAGE 63
00.book 61 ページ２００１年４月２０日金曜日午後９時３４分 JOB MEMORY Nine frequently used job programs can be stored in each of nine storage registers. This is convenient for quick job recall without losing time manually reprogramming each aspect of a job. ● The following functions cannot be stored in the job memory: copy quantity, original size, document station (platen glass or document feeder tray), paper size, interrupt, extra image adjustment.
PAGE 64
JOB MEMORY 4 Select a program number from 1 to 9 using the numeric keys. ●A screen indicating that the settings have been stored will appear and then the display will return to the basic screen. ● The numbers with a check mark are program numbers which already contain job programs. If a program number containing a job program is entered, the message "Storage number selected is already used. Replace it?" will appear to confirm the selection.
PAGE 65
00.book 63 ページ２００１年４月２０日金曜日午後９時３４分 JOB MEMORY 3 Select a program number from 1 to 9 using the numeric keys. ● The numbers with a check mark are program numbers which contain job programs. If a checked number is entered, the message "Delete job program?" will appear to confirm the selection to delete the program. To delete the program, select "YES" with the and keys and press the OK key. ● If "NO" is selected, the previous screen will reappear.
PAGE 66
00.book 64 ページ２００１年４月２０日金曜日午後９時３４分 JOB MEMORY 3 Select a program number from 1 to 9 using the numeric keys. ● The numbers with a check mark are program numbers which contain job programs. If a checked number is entered, the settings for that job program will be recalled and the display will return to the basic screen. ● The recalled settings may be modified for a particular job run, but any changes made will not be stored in the job memory.
PAGE 67
00.book 65 ページ２００１年４月２０日金曜日午後９時３４分 CHAPTER 4 COPIER TROUBLE? This chapter describes how to remove misfed paper and how to remedy minor problems. Page MESSAGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 ● MISFEED REMOVAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Misfeed in the bypass tray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 Misfeed in the copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 68
00.book 66 ページ２００１年４月２０日金曜日午後９時３４分 STATUS MESSAGES If any of the following messages appears in the display, carry out the prescribed remedy. Message Remedy Maintenance required soon. Service by an authorized SHARP service technician will be required soon. Contact your service center as soon as possible.(This message will be displayed if the information key is pressed when the information ( ) icon is displayed.) Maintenance required. Call for service.
PAGE 69
00.book 67 ページ２００１年４月２０日金曜日午後９時３４分 MISFEED REMOVAL When a misfeed occurs, the copier will stop. The message "Clear paper path." will appear in the display along with an illustration showing paper misfeed locations. ● If paper becomes accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. ● For misfeeds in optional equipment, see their respective sections of the operation manual.
PAGE 70
MISFEED REMOVAL Misfeed in the copier Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”. If paper is misfed here, proceed to “A. Misfeed in the paper feed area”. A. Misfeed in the paper feed area COPIER TROUBLE? 68 1 Open the bypass tray and the side cover. 2 Gently open the front cover. If paper is misfed here, proceed to “B.
PAGE 71
MISFEED REMOVAL 3 Carefully remove the misfed paper. Turn the roller rotating knob in the direction of the arrow to assist in removing it. WARNING: The fusing unit is hot. Take care in removing paper. CAUTION: Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies. 4 Close the front cover and the side cover. ● Confirm 4 that the misfeed display has been cleared. B.
PAGE 72
MISFEED REMOVAL 3 Turn the roller rotating knob in the direction of the arrow. Roller rotating knob 4 Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. After removal, return the release levers to their operating positions. Fusing unit release lever WARNING: The fusing unit is hot. Take care in removing paper. CAUTION: not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may damage the drum and cause smudges on copies.
PAGE 73
MISFEED REMOVAL C. Misfeed in the transport area 1 Open the bypass tray and the side cover. 2 Use the green tabs on either side of the paper guide to rotate the guide open and remove the misfed paper WARNING: The fusing unit is hot. Take care in removing paper. 3 Close the side cover. ● Confirm 4 that the misfeed display has been cleared. COPIER TROUBLE? Misfeed in the center tray 1 Remove the paper by pulling it into the center tray.
PAGE 74
MISFEED REMOVAL Misfeed in the upper paper tray Before opening the upper paper tray, be sure to open the bypass tray and the side cover and then perform steps 1 to 3 described in the "A. Misfeed in the paper feed area" section. 1 Pull out the upper paper tray and remove the misfed paper. 2 Close the paper tray. 3 Open and close the side cover to cancel the misfeed display. COPIER TROUBLE? ● You can also cancel the misfeed display by opening and closing the front cover.
PAGE 75
MISFEED REMOVAL 2 Remove the misfed paper. ● Be 3 careful not to tear the misfed paper during removal. If the misfed paper is not seen in step 2, pull out the lower paper tray and remove the misfed paper. ● Be careful not to tear the misfed paper during removal. 4 Close the paper tray. 5 Close the lower side cover. COPIER TROUBLE? ● Confirm 4 that the misfeed display has been cleared.
PAGE 76
00.book 74 ページ２００１年４月２０日金曜日午後９時３４分 MISFEED REMOVAL COPIER TROUBLE? 74 2 Gently pull the misfed paper out. 3 Close the upper exit area cover. ● Confirm that the misfeed display has been cleared.
PAGE 77
00.book 75 ページ２００１年４月２０日金曜日午後９時３４分 TROUBLESHOOTING Always check the message display whenever the copier stops during an operation or operation is not possible. Messages in the display will give you easy-to-follow directions. For other troubles not described by messages, check the chart below. Problem Solution Copier plugged in? Plug the copier into a grounded outlet as specified. See page 89. ● Power switch ON? Turn the power switch ON. See page 16. Copies are too dark or too light.
PAGE 78
00.book 76 ページ２００１年４月２０日金曜日午後９時３４分 TROUBLESHOOTING Problem Solution ● Platen glass or platen cover Clean regularly. See page 84. dirty? ● Original smudged or blotchy? Black or white stripes appear on copies. ● Is the scanning window of an Clean the scanning window. optional SPF or RSPF dirty? Paper size for a paper tray cannot be set.
PAGE 79
00.book 77 ページ２００１年４月２０日金曜日午後９時３４分 CHAPTER 5 GENERAL INFORMATION Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Types and sizes of copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Loading copy paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 Changing the copy paper size in the tray. . . . . . . . . . . . . . . . . . . . 80 ● TONER CARTRIDGE REPLACEMENT. . . . . . . . . . . . . . . . . . . . .
PAGE 80
00.book 78 ページ２００１年４月２０日金曜日午後９時３４分 PAPER Types and sizes of copy paper Types and sizes of copy paper which can be fed from the paper trays are shown below. For paper acceptable for feeding from the bypass tray, see page 36. Size Weight Capacity (21 lb. bond paper) 5-1/2" x 8-1/2" to 11" x 17" A5 to A3 15 lbs. to 21 lbs. 500 sheets ● 5-1/2" x 8-1/2" and A5 copy papers cannot be fed from any tray except the uppermost tray.
PAGE 81
PAPER 3 Move the left guide to the appropriate slot as marked on the tray. 4 Fan the copy paper and insert it into the tray. ● When using 11" x 17" copy paper, store the left guide in the slot at the left front of the paper tray. ● Set the paper along the guides. tray holds up to 500 sheets of 21 lb. bond paper. ● Do not load paper above the maximum height line. ● The 5 Push the paper tray firmly back into the copier.
PAGE 82
00.book 80 ページ２００１年４月２０日金曜日午後９時３４分 PAPER Changing the copy paper size in the tray Paper size setting can only be done while the machine is not operating and the COPY mode has been selected. ● B5 paper cannot be set for paper tray 2. 1 Press the SPECIAL FUNCTION key. ● The SPECIAL FUNCTION screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 2 Use the key.
PAGE 83
00.book 81 ページ２００１年４月２０日金曜日午後９時３４分 PAPER 5 Use the ● To 6 keys to select the paper size that has been set. change the size of another paper tray, press the key and then repeat steps 3 to 5. Press the OK key. ●A 7 and confirmation message for paper size setting will appear. Press the OK key. ● The specified paper size will be registered and the display will return to the basic screen.
PAGE 84
TONER CARTRIDGE REPLACEMENT The approximate quantity of toner remaining can be displayed by pressing and holding the COPY key during standby or warm-up. See page 84. When the quantity of toner remaining is less than 25%, obtain a new cartridge. When the toner cartridge replacement required icon ( ) appears in the display, replacement of the toner cartridge will be needed soon. If you press the information key, the message "Toner is low." will appear in the display. When the message "Add toner.
PAGE 85
TONER CARTRIDGE REPLACEMENT 3 Remove the new toner cartridge from the bag. Grasp the cartridge on both sides and shake it horizontally approximately 20 times. After shaking the cartridge, remove the tape. NOTE: Grasp the grip when holding the cartridge. Do not hold the cartridge by the shutter. Be sure to only shake the cartridge before the tape is removed. 4 Gently insert the toner cartridge along the guides until it clicks in place while pushing the lock release lever.
PAGE 86
00.book 84 ページ２００１年４月２０日金曜日午後９時３４分 CHECKING THE TONER QUANTITY AND TOTAL OUTPUT COUNT The approxmate quantity of toner remaining and the total output count can be displayed by the procedure below. The total count value displayed is the output count in the copy, print, and fax modes including the output count by the self-print function of the printer and facsimile features. 1 Press and hold the COPY key during standby or warm-up.
PAGE 87
00.book 85 ページ２００１年４月２０日金曜日午後９時３４分 CLEANING THE PLATEN GLASS AND PLATEN COVER Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Stains or dirt on the platen glass or platen cover will also be copied. Wipe the platen glass and platen cover with a soft, clean cloth. ● If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents.
PAGE 88
00.book 86 ページ２００１年４月２０日金曜日午後９時３４分 CLEANING THE BYPASS TRAY PAPER FEED ROLLER If misfeeds occur frequently when feeding postcards, envelopes, thick paper, etc. through the bypass tray, wipe the paper feed roller at the feed slot of the bypass tray with a soft, clean cloth dampened with alcohol or water.
PAGE 89
DISPLAY CONTRAST ADJUSTMENT The contrast of the display can be adjusted as below. 1 Press the SPECIAL FUNCTION key. ● The SPECIAL FUNCTION screen will appear. SPECIAL FUNCTION SPECIAL MODES ORIG. SIZE ENTER PAPER SIZE SET DISPLAY CONTRAST 2 Use the OK key. ● The 3 and keys to select "DISPLAY CONTRAST" and press the screen for contrast setting will appear. Use the and keys to adjust the contrast. 5 4 GENERAL INFORMATION ● To reset the contrast to the default setting, press the CLEAR key.
PAGE 90
00.book 88 ページ２００１年４月２０日金曜日午後９時３４分 STORAGE OF SUPPLIES Standard supplies for this copier that are to be replaced by the user are copy paper, toner cartridge, and staple cartridge for the optional finisher (AR-FN5). For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered, and tested to maximize the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.
PAGE 91
00.book 89 ページ２００１年４月２０日金曜日午後９時３４分 SPECIFICATIONS AR-235 Type Digital copying machine, desktop Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. 11" x 17" Copy sizes Max. 11" x 17", Min. 5-1/2" x 8-1/2" AR-275 Image loss: Max. 5/32" (4 mm) (leading and trailing edges), Max. 1/8" (3 mm) (along other edges) Copying speed (one-sided copying at 100% copy ratio) 600 dpi 1200 dpi 23 copies/min. (8-1/2" x 11") 27 copies/min.
PAGE 92
00.book 90 ページ２００１年４月２０日金曜日午後９時３４分 SPECIFICATIONS Power consumption Max. 1.2 kW Overall dimensions (with bypass tray folded) 24-13/16" (W) x 23-3/64" (D) (628 mm (W) x 585.5 mm (D)) Weight Approx. 105.2 lbs. (47.8 kg), toner cartridge included Copier dimensions (without platen cover) 24-13/16" (W) x 23-3/64" (D) x 25-21/64" (H) Operating conditions Temperature: 59°F to 86°F (15°C to 30°C) (628 mm (W) x 585.
PAGE 93
00.book 91 ページ２００１年４月２０日金曜日午後９時３４分 CHAPTER 6 OPTIONAL EQUIPMENT This chapter describes operating instructions for the Single Pass Feeder (AR-SP4), the Reversing Single Pass Feeder (AR-RP3), the Finisher (AR-FN5), the 500-Sheet Paper Feed Unit (AR-D11), and the 2 x 500-Sheet Paper Feed Unit (AR-D12). Page CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 ● SINGLE PASS FEEDER (AR-SP4)/ REVERSING SINGLE PASS FEEDER (AR-RP3) . . . . . . . . . . . . . 93 Part names. . . . . . . .
PAGE 94
SYSTEM CONFIGURATION A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following.
PAGE 95
00.book 93 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (ARSP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) The single pass feeder (SPF) and the reversing single pass feeder (RSPF) hold up to 30 originals each for automatic document feeding. If the RSPF is installed, two-sided originals can be copied automatically without having to manually turn them over.
PAGE 96
00.book 94 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) Specifications Acceptable originals Weight Size 15 to 23 lbs. 5-1/2" x 8-1/2"* to 11" x 17" * 5-1/2" x 8-1/2" size originals cannot be used in the duplex copy mode.
PAGE 97
00.book 95 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) Stream feeding mode If the stream feeding mode has been enabled using a key operator program, the message "Set originals for stream feeding." will appear for approximately 5 seconds after feeding of all originals is completed. While this message is displayed, any new originals placed in the SPF or RSPF will be fed and copied automatically.
PAGE 98
00.book 96 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) 4 Ensure that the one-sided to one-sided copying mode is selected. Ready to copy. 81/2 11 AUTO 100% 81/2 11 AUTO ● When no icon indicating a duplex copy mode is displayed, the one-sided to one-sided copying mode is selected. 5 Set the number of copies and press the START key. ● Press the CLEAR key to stop copying in the middle of a run.
PAGE 99
00.book 97 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) 2 Press the 2-SIDED COPY key. ● The duplex copy mode selection screen will appear. COPY MODE 1 to 1 1 2 1 to 2 2 2 2 to 2 3 Use the ● Also and keys to select one-sided to two-sided copying. the 2-SIDED COPY key can be used to select a duplex copy mode. COPY MODE 1 to 1 1 2 1 to 2 2 2 2 to 2 BINDING CHANGE OFF 4 Use the or the OK key. key to select binding change if desired.
PAGE 100
00.book 98 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) Two-sided copies from two-sided originals To copy in the two-sided to two-sided copy mode, an RSPF must be installed. ● Paper sizes that can be used in the duplex copy mode are 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14", 11" x 17", A5, B5, B5R, A4, A4R, B4, and A3. 1 Ensure that no original is left on the platen glass.
PAGE 101
00.book 99 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) 4 Set the number of copies and press the START key. ● Be sure not to touch the originals as they move on the reversing tray. This may cause misfeeds. One-sided copies from two-sided originals To copy in the two-sided to one-sided copy mode, an RSPF must be installed. 1 Ensure that no original is left on the platen glass.
PAGE 102
00.book 100 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) 3 Use the and keys to select two-sided to one-sided copying. COPY MODE 1 2 1 to 2 2 2 2 to 2 2 1 2 to 1 BINDING CHANGE OFF 4 Use the OK key. or key to select binding change if desired. Then, press the ● The image of one side can be rotated 180º using the image rotation feature. This feature can be useful depending on the orientation of the original image and the desired binding position.
PAGE 103
00.book 101 ページ２００１年４月２０日金曜日午後９時３４分 SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) Misfeed removal If an original misfeed occurs in the SPF or RSPF, the copier will stop and the message "Clear paper path." will appear. 1 Remove the misfed originals. A B C Location A Open the feeding roller cover and pull the misfed original gently to the left and out from the document feeder tray. Close the feeding roller cover.
PAGE 104
SINGLE PASS FEEDER (AR-SP4)/REVERSING SINGLE PASS FEEDER (AR-RP3) ● If a small original such as 5-1/2" x 8-1/2" original has misfed or an original has misfed in the reversing tray (when an RSPF is installed), open the right side cover and gently remove the misfed original. Close the right side cover. Right side cover Location C Gently remove the misfed original from the exit area.
PAGE 105
00.book 103 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) The copier has two different finisher modes: one sorts copies into sets matching the sequence of the originals and the second groups copies by original. When an optional finisher (AR-FN5) is installed, the copier can automatically staple the sorted copies. Each collated set of copies or group of copies can be stacked offset from the previous set.
PAGE 106
00.book 104 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) Specifications Tray capacity Top tray: 100 sheets Offset tray: 1,000 sheets (500 sheets for sizes larger than 8-1/2" x 11") Paper size Top tray: 5-1/2" x 8-1/2" to 11" x 17" Offset tray: 8-1/2" x 11" to 11" x 17" Paper weight Top tray: 15 lbs. to 21 lbs. Offset tray: 15 lbs. to 21 lbs. Offset Approx.
PAGE 107
00.book 105 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) Finisher functions When the finisher is installed, the following four output modes can be selected: sort, staple sort, group, and non-sort. Press the OUTPUT key, use the and keys (or the OUTPUT key) to select the desired output mode, and then press the OK key. When copying in the sort or group mode, the output tray can be selected using the and keys and pressing the OK key.
PAGE 108
00.book 106 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) Staple sort In the staple sort mode, 8-1/2" x 11", 8-1/2" x 11"R, 8-1/2" x 13", 8-1/2" x 14", 11" x 17", B5, A4, A4R, B4, and A3 size copies can be stapled. NOTE: Different size originals cannot be copied onto copy paper of their respective sizes in the staple sort mode. ★KEY OPERATOR If stapler is disabled using a key operator program, the staple sort mode cannot be used. See page 19 of the KEY OPERATOR'S GUIDE.
PAGE 109
00.book 107 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) 3 Use the 4 Set the number of copies and press the START key. 5 Replace the scanned original with the next original and press the START key after it lights up. Repeat this step until all originals have been scanned. 6 After all originals have been scanned, press the READ-END key. ● Also and keys to select "STAPLE SORT" and press the OK key. the OUTPUT key can be used to select an output mode.
PAGE 110
00.book 108 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) Using the SPF or the RSPF 1 Set the originals in the document feeder tray. Stapling position ● If the number of copies in one set is more than 30, the copies will not be stapled. the orientation of the originals does not match that of the copy paper, the images of the originals will be rotated. The stapling position varies with the orientation of the original.
PAGE 111
00.book 109 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) 4 Set the number of copies and press the START key. ● When copying of a set is completed, the copies will be automatically stapled and delivered to the offset tray. Staple cartridge replacement When the message "Add staples." appears, replace the staple cartridge as follows: 1 Open the stapler cover. 2 Grasp the green portion of the staple box and remove the staple box from the stapler.
PAGE 112
FINISHER (AR-FN5) 4 Insert the new staple cartridge into the box until it clicks into place. ● Insert the new cartridge by aligning the arrows on the cartridge with those on the box. Check that the cartridge locks in place by pulling it slightly. ● A cartridge holds 3,000 staples. 5 Remove the tape from the cartridge. 6 Insert the staple box into the stapler unit until it clicks into place. 7 Close the stapler cover.
PAGE 113
FINISHER (AR-FN5) 2 Grasp the green portion of the staple box and remove the staple box from the stapler. 3 Raise the lever at the end of the staple box and remove the jammed staples. 4 Return the lever to its original position. 5 Insert the staple box into the stapler unit until it clicks into place. 6 Close the stapler cover.
PAGE 114
00.book 112 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) Misfeed removal The copier will stop when a misfeed occurs. The message "Clear paper path." will appear along with a display of paper misfeed locations. When a misfeed is indicated for the finisher, follow the procedure below. OPTIONAL EQUIPMENT 112 1 Pull the handle of the stapler compiler cover and open the cover. 2 Remove any misfed paper from the transport area.
PAGE 115
00.book 113 ページ２００１年４月２０日金曜日午後９時３４分 FINISHER (AR-FN5) 4 Close the stapler compiler cover. 5 If the offset tray is being used, remove any misfed paper from the offset tray. 6 If the top tray is being used, open the top cover, remove any misfed paper, and close the top cover. ● Confirm that the misfeed display has been cleared.
PAGE 116
00.book 114 ページ２００１年４月２０日金曜日午後９時３４分 500-SHEET PAPER FEED UNIT (AR-D11)/2x500-SHEET PAPER FEED UNIT (AR-D12) These paper feed units provide the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying. The AR-D11 contains one 500-sheet paper tray and the AR-D12 contains two 500-sheet paper trays.
PAGE 117
00.book 115 ページ２００１年４月２０日金曜日午後９時３４分 500-SHEET PAPER FEED UNIT (AR-D11)/2x500-SHEET PAPER FEED UNIT (AR-D12) Loading copy paper The method of loading copy paper for these paper feed units is the same as for the paper trays in the copier. See page 78. Changing the copy paper size in the tray The method of changing the copy paper size is the same as for the paper trays in the copier. See page 80. Misfeed removal The copier will stop when a misfeed occurs. The message "Clear paper path.
PAGE 118
00.book 116 ページ２００１年４月２０日金曜日午後９時３４分 500-SHEET PAPER FEED UNIT (AR-D11)/2x500-SHEET PAPER FEED UNIT (AR-D12) OPTIONAL EQUIPMENT 116 2 Pull out the paper tray which was in use. 3 Remove any misfed paper. 4 Close the paper tray. 5 Close the side cover. ● Confirm that the misfeed display has been cleared.
PAGE 119
00.book 117 ページ２００１年４月２０日金曜日午後９時３４分 INDEX 2 E 2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 2x500-sheet paper feed unit . . . . . . . . . . . . . 114 Edge erase . . . . . . . . . . . . . . . . . . . . . . . . . . . Enlargement . . . . . . . . . . . . . . . . . . . . . . . . . . Erase . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Exposure adjustment . . . . . . . . . . . . . . . . . . . . Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 120
00.book 118 ページ２００１年４月２０日金曜日午後９時３４分 INDEX N S Names – operation panel . . . . . . . . . . . . . . . . . . . . . . 14 – part. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Non-sort . . . . . . . . . . . . . . . . . . . . . . . . . . 43, 105 Single pass feeder (SPF). . . . . . . . . . . . . . . . . 93 Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42, 105 Special paper. . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 121
00.book 119 ページ２００１年４月２０日金曜日午後９時３４分 MATERIAL SAFETY DATA SHEET Date Issued : Apr. 2. 2001 MSDS NO. F-00981 1. PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-270NT/270T/270ST/270FT/270NT-J/270ST-C/270FT-T (Black Toner) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A.
PAGE 122
00.book 120 ページ２００１年４月２０日金曜日午後９時３４分 5. FIRE -FIGHTING MEASURES Extinguishing Media : water, CO2, foam and dry chemicals Special Fire fighting Procedures : None Fire and Explosion Hazards : Toner material, like most finely divided organic powders, may form an explosive mixture. 6. ACCIDENTAL RELEASE MEASURES Personal Precautions : None Environmental Precautions: None Methods for Cleaning Up : Wipe off with paper or cloth. Do not use vacuum cleaner when a large amount is released.
PAGE 123
00.book 121 ページ２００１年４月２０日金曜日午後９時３４分 10. STABILITY AND REACTIVITY : Stability Hazardous Reactions : Conditions to avoid : Materials to avoid : Hazardous Decomposition Products : Further Information : Stable Dust explosion, like most finely divided organic powders. Electric discharge, throwing into fire. Oxidizing Materials CO, CO2 and NOx None 11.
PAGE 124
00.book 122 ページ２００１年４月２０日金曜日午後９時３４分 15. REGULATORY INFORMATION US Information TSCA (Toxic Substances Control Act): All chemical substances in this product comply with all applicable rules or order under TSCA.
PAGE 125
00.book 123 ページ２００１年４月２０日金曜日午後９時３４分 Date Issued : Apr. 2. 2001 MSDS NO. F-30981 1. PRODUCT AND COMPANY IDENTIFICATION Product Name : AR-270ND/270DV/270SD/270SD-C (Black Developer) Supplier Identification : Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A.
PAGE 126
00.book 124 ページ２００１年４月２０日金曜日午後９時３４分 5. FIRE -FIGHTING MEASURES Extinguishing Media : water, CO2, foam and dry chemicals Special Fire fighting Procedures : None Fire and Explosion Hazards : Like most finely divided organic powders, it may form an explosive mixture. 6. ACCIDENTAL RELEASE MEASURES Personal Precautions : None Environmental Precautions: None Methods for Cleaning Up : Wipe off with paper or cloth. Do not use vacuum cleaner when a large amount is released.
PAGE 127
00.book 125 ページ２００１年４月２０日金曜日午後９時３４分 10. STABILITY AND REACTIVITY : Stability Hazardous Reactions : Conditions to avoid : Materials to avoid : Hazardous Decomposition Products : Further Information : Stable Dust explosion, like most finely divided organic powders. Electric discharge, throwing into fire. Oxidizing Materials CO, CO2 and NOx None 11.
PAGE 128
00.book 126 ページ２００１年４月２０日金曜日午後９時３４分 15. REGULATORY INFORMATION US Information TSCA (Toxic Substances Control Act): All chemical substances in this product comply with all applicable rules or order under TSCA.
PAGE 129
WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user's authority to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
PAGE 130
AR-235/AR-275 SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07430-2135. www.sharp-usa.