MODEL AR-160 AR-161 DIGITAL COPYING MACHINE OPERATION MANUAL Page • GETTING STARTED • MAKING COPIES • STATUS INDICATORS • GENERAL INFORMATION • OPTIONAL EQUIPMENT • APPENDIX 2 13 27 36 53 69
CAUTIONS Follow the cautions below when using this copier. ● The fusing area is hot. Exercise care in this area when removing misfed paper. ● Do not look directly at the light source. Doing so may damage your eyes. ● Place the copier on a firm, level surface. ● Do not install the copier in a humid or dusty location. ● When the copier is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.
CONTENTS Page GETTING STARTED ● ● ● ● ● INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 MAIN FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PART NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . 4 – Overall layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 – Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 COPIER INSTALLATION . . . . . . . . . . . . . . .
INTRODUCTION GETTING STARTED This copier has been designed to provide convenient copying features in a minimum amount of office space and with maximum operational ease. To get full use of all copier features, be sure to familiarise yourself with this manual and the copier. For quick reference during copier use, keep this manual in a handy location. This copier can be used as a laser printer and as a facsimile machine by installing optional components.
MAIN FEATURES GETTING STARTED q High-speed laser copying ● First-copy time is only 7.2 seconds (except in a power save mode or immediately after power on). ● Copying speed is 16 copies/min., which adapts to business use, allowing improvement of working efficiency. w High-quality digital image ● High-quality copying at 600 dpi is performed. In addition to the automatic exposure mode, the manual exposure can be adjusted in five steps.
PART NAMES AND FUNCTIONS GETTING STARTED Overall layout e Part names and functions q o !1 w !2 e y !0 !3 u r t !4 i q Platen cover Place the original on the original table and close the platen cover before copying starts. w Original table Place the document to be copied here. e Handles Use to move the copier. r Power switch Press to turn copier power on and off. i Paper tray Holds 250 sheets of copy paper. o Side cover Open to remove misfeeds and to service the copier.
PART NAMES AND FUNCTIONS GETTING STARTED Part names and functions !5 !6 !7 @2 !8 !9 @0 !5 Drum cartridge handle Hold to pull out the drum cartridge. !6 Drum cartridge Copy images are formed on the photoconductive drum. !7 TD cartridge lock release lever Use to unlock the TD cartridge. @1 @1 Fusing unit release levers Lower to remove misfed paper. The fusing unit is hot. Take care in removing paper. @2 Paper guide Open to remove misfed paper. !8 TD cartridge strap Lift to remove the TD cartridge.
PART NAMES AND FUNCTIONS Operation panel q w e r t y u i o !0 !1 !2 GETTING STARTED Part names and functions !8 !9 @0 @1 @2 @3 @4 @5 @6 @7 @8 @9 #0 Not used for the copier features. q INTERRUPT key and indicator (p. 25) Interrupts a copy run. !3 B/W REVERSE key and indicator (p. 23) Press to reverse the black and white areas. w Copy quantity display Displays the specified copy quantity during the ready condition and displays the copy countdown as copies are made.
PART NAMES AND FUNCTIONS !3 !5 !6 #1 #2 !7 GETTING STARTED !4 Part names and functions #3 1st display Press and hold down the key. 2nd display 12,345 sheets output Note: A3 size copies are counted as two copies. @2 CLEAR key Clears the copy quantity display or terminates a copy run. @3 START key and indicator Copying is possible when the indicator is on. Press to start copying. @4 CLEAR ALL ( ) key Clears all selected settings and returns the copier to the initial settings.
COPIER INSTALLATION GETTING STARTED Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.
CAUTIONS ON HANDLING GETTING STARTED Be careful in handling the copier as follows to maintain the performance of this copier. Do not drop the copier, subject it to shock or strike it against any object. Cautions on handling Do not expose the drum cartridge to direct sunlight. Doing so will damage the surface (green portion) of the drum cartridge, causing poor copy quality. Store spare supplies such as drum cartridges and TD cartridges in a dark place without removing from the package before use.
LOADING COPY PAPER GETTING STARTED To save space, this copier has been designed with an adjustable front-loading tray, which is easily opened for paper loading. For best results, use only SHARP recommended paper. (See page 49.) The paper required ( ) indicator will light up when there is no copy paper in the selected paper feed station, or when the selected paper tray is not installed or is improperly installed.
LOADING COPY PAPER GETTING STARTED Loading copy paper Changing the copy paper size in the tray Left guide 1 Gently lift and pull out the paper tray until it stops. 2 Push the pressure plate down until it locks in place. 3 Squeeze the lock lever of the front guide and slide the front guide to match the width of the paper. 4 Move the left guide to the appropriate slot as marked on the tray. ● Front guide 5 6 7 When using A5 copy paper, load it into the uppermost paper tray.
LOADING COPY PAPER GETTING STARTED Loading copy paper 8 To set the selected paper size, press the PAPER SIZE ENTER key. ● The selected paper feed location indicator will blink and the corresponding paper size (which is currently set) indicator will light up steadily. All other indicators will go out. For paper size setting, ensure that the COPY mode has been selected. However, if copying, printing or facsimile printing is being performed, paper size setting cannot be made even in the COPY mode.
AUDITING ACCOUNTS If this copier has been programmed in the auditing mode, it will not function until an assigned 3-digit account number has been entered. See page 39 for setting the auditing mode. 2 ● As each digit is entered, the dashes in the copy quantity display will disappear. ● After the number is entered, the copy quantity display will change to 0. ● If an unassigned number is entered, “– – –” will appear again in the copy quantity display, indicating that the number was not accepted.
NORMAL COPYING Power on 1 Turn the power switch on. ● ● MAKING COPIES ● 2 Place the original face down on the original table. Align it with the original size scale. ● Image loss (max. 4 mm) can occur at the leading and trailing edges of the copies. Also image loss (max. 4 mm in total) can occur along the other edges of the copies. Normal copying 3 Close the platen cover. 4 Ensure that the copy paper size in the paper tray is the same size as the original.
NORMAL COPYING ● For photographs, select PHOTO and then adjust with the light ( and dark ( ) keys as desired. ● There are 5 exposure steps indicated by 3 indicator lights. (The indicators light up one or two at a time.) If exposure level 2 is selected, the two left-handmost indicators for that level will light up simultaneously. Also, if level 4 is selected, the two right-handmost indicators for that level will light up simultaneously. ) Set the number of copies using the numeric keys.
REDUCTION/ENLARGEMENT/ZOOM Reduction and enlargement ratios can be selected either automatically with the AUTO IMAGE key or manually with the PRESET RATIO selector ( , ) keys and/or the zoom ( , ) keys. The zoom function enables precise copy ratio selection from 50% to 200% in 1% increments. MAKING COPIES Automatic 1 Reduction/enlargement/zoom 2 3 Place the original on the original table and close the platen cover.
REDUCTION/ENLARGEMENT/ZOOM Manual 2 Use the PRESET RATIO selector ( , ) keys and the zoom ( , ) keys to select the desired copy ratio. A. B. C. ● When a zoom ( , ) key is pressed, the ZOOM indicator will light up and the zoom ratio will be displayed in the copy quantity display for at least two seconds. ● To verify a zoom setting without changing the zoom ratio, press and hold down the copy ratio display ( ) key. When the key is released, the display will return to the copy quantity display.
BYPASS FEED (special paper) The bypass tray is used to copy onto transparency film, labels, and other special purpose papers. Up to 100 sheets of standard copy paper can be set in the bypass tray. For special purpose papers, the original image must be smaller than the paper or media for copying. If the original image is bigger than the paper or media, this may cause smudges on the edges of the copies.
BYPASS FEED (special paper) 6 Leave the copy quantity at 0 if using special papers. Set the number of copies if using standard copy paper or envelopes. Press the START key. 19 Bypass feed (special paper) 5 MAKING COPIES 4 Press the TRAY SELECT key to select the bypass tray.
TWO-SIDED COPYING Two-sided copies can be made on this copier using the bypass tray. MAKING COPIES 1 Place the first original on the original table and make a copy. ● Two-sided copying 2 3 Replace the first original with the second original and close the platen cover. ● Make sure that the first and second originals are oriented in the same way on the original table.
XY ZOOM Original Copy The XY ZOOM feature allows the horizontal and vertical copy ratios to be changed independently. This feature cannot be used with the 2 in 1 or 4 in 1 feature. (The 2 in 1 or 4 in 1 feature can only be used when an optional electronic sorting kit and an optional SPF are installed.) To use the XY ZOOM feature with the DUAL PAGE COPY feature, set the DUAL PAGE COPY feature first and then the XY ZOOM feature. (Enlargement cannot be set.) Press the XY-ZOOM key.
XY ZOOM 5 MAKING COPIES 6 Use the PRESET RATIO selector ( , ) keys and zoom ( , ) keys to change the copy ratio in the horizontal direction in a similar manner as for the vertical direction. Press the copy ratio display ( ● The selected ratio for the horizontal direction will be entered and the display will change to the copy quantity display. ● To verify the copy ratios, press and hold down the copy ratio display ( ) key. The vertical and horizontal ratios will be alternately displayed.
B/W REVERSE Original Copy The B/W REVERSE feature is used to reverse black and white areas. ● When the B/W REVERSE feature is selected, the exposure mode will be automatically set to the MANUAL mode. Other exposure modes cannot be selected. Even if this feature is cancelled, the MANUAL mode will not automatically be cancelled. Press the B/W REVERSE key. 3 Check the copy paper size. 4 Make all other desired copier selections and press the START key.
DUAL PAGE COPY Original Copy The DUAL PAGE COPY feature produces individual copies of two documents placed side by side on the original table. It is especially useful when copying books and other bound documents. This feature cannot be used with the 2 in 1 or 4 in 1 feature and sort/group feature. (The 2 in 1 or 4 in 1 feature and sort/group feature can only be used when an optional electronic sorting kit and an optional SPF are installed.
INTERRUPTING A COPY RUN INTERRUPT is used to interrupt a long copy run so that another job can be done. ● If sort or group copying is being performed, sort or group cannot be selected during interrupt copying. (Sort and group can be performed only if an optional electronic sorting kit and an optional SPF are installed.) ● ● 2 3 4 5 6 When the copier stops, remove the original(s) and set the original(s) for interrupt copying. Select the desired available copier functions. Set the number of copies.
AUTOMATIC EXPOSURE ADJUSTMENT The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the optional SPF respectively. To set the level for the optional SPF, place an original in the SPF tray and make sure that the SPF indicator lights up before proceeding to step 1. To set the level for the original table, ensure that the SPF indicator does not light up.
TD CARTRIDGE REPLACEMENT If the machine detects an insufficient amount of toner being added, copying will stop and the machine will add toner. During this time, the START key indicator will blink. When sufficient toner has been added, the indicator will go out indicating that copying can be resumed. However, if toner addition continues for a maximum of two minutes, the TD cartridge replacement required ( ) indicator will light up in addition to the START key being lighted steadily.
TD CARTRIDGE REPLACEMENT 5 Remove the protective cover from the TD cartridge by unlatching three cover hooks from the holes on the cartridge and then pulling the cover in the direction indicated by the arrow in the illustration. STATUS INDICATORS TD cartridge replacement 6 Gently insert the TD cartridge along the guides until it locks in place. If dirt or dust is adhered to the TD cartridge, remove it before installing the cartridge.
DRUM CARTRIDGE REPLACEMENT The useful life of the drum cartridge is approximately 30,000 copies. When the internal counter reaches approximately 29,000 copies, the drum replacement required ( ) indicator will light up indicating that replacement of the drum cartridge will be needed soon. When the indicator begins to blink, replace the drum cartridge by following the procedure given below. For best copying results, be sure to use only SHARP products.
DRUM CARTRIDGE REPLACEMENT 5 Remove the new drum cartridge from the protective bag and gently insert the lead end of the drum cartridge along the guides. Do not touch the surface of the drum (green portion) of the cartridge. Doing so may cause smudges on the copies. STATUS INDICATORS Drum cartridge replacement 6 Remove the protective cover from the drum cartridge and then push the cartridge all the way into the copier. 7 Gently install the TD cartridge.
MISFEED REMOVAL The copier will stop when a misfeed occurs. The misfeed ( ) indicator will blink, and blinking red misfeed location indicators will indicate the approximate misfeed location. If paper is accidentally torn during removal, be sure to remove all pieces. Be careful not to damage the photoconductive drum. For misfeeds in optional equipment, see their respective sections of the operation manual. First confirm the misfeed location. ( P.57) ( P.31, 34) ( P.
MISFEED REMOVAL 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If paper is misfed here, proceed to “B. Misfeed in the fusing area”. If the misfed paper is seen from this side, proceed to “C. Misfeed in the transport area”. If paper is misfed here, proceed to “A. Misfeed in the paper feed area”. A. Misfeed in the paper feed area 1 Push gently on both sides of the front cover to open the cover.
MISFEED REMOVAL Roller rotating knob 2 3 Turn the roller rotating knob in the direction of the arrow. Carefully remove the misfed paper. Lower the fusing unit release levers to allow easier removal. Return the release levers to their operating positions. Fusing unit release lever The fusing unit is hot. Take care in removing paper. ● 4 Close the front cover by pushing both sides with your hands and then close the side cover by pressing the handle on the cover. The misfeed ( will light up.
MISFEED REMOVAL 3 Close the side cover by pressing the handle on the cover. ● The misfeed ( will light up. ) indicator will go out and the START key indicator Misfeed in the paper tray Before opening the paper tray, be sure to open the bypass tray, lift slightly on the side cover and slide the cover out until it stops, and then perform steps 1 to 3 described in the “A. Misfeed in the paper feed area” section. STATUS INDICATORS 1 Gently lift and pull out the paper tray and remove the misfed paper.
MAINTENANCE REQUIRED When the indicator lights up, service by an authorised SHARP service technician is required. Contact your service centre as soon as possible.
USER PROGRAMS The user programs allow the parameters of certain functions to be set, changed, or cancelled as desired. List of user programs This copier has the following user programs. Program No. GENERAL INFORMATION User programs Program name Description 1 Auto clear time Sets the auto clear time. The copier returns to the initial settings when the auto clear time elapses after the last copy is made.
USER PROGRAMS Setting the user programs 1 2 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and “– –” appears in the copy quantity display. Enter a program number using the numeric keys. ● The selected program number will blink in the copy quantity display. ● If a mistake is made in steps 2 to 4, press the CLEAR ( copier will return to step 2. ● The program numbers are shown in the table below. ) key.
USER PROGRAMS 4 Select the desired parameter using the numeric keys. ● The entered parameter number will blink on the right side of the copy quantity display. ● The parameters are shown in the table below. For example, to change the setting of the auto power shut-off timer to 60 min., press key 2. Program name Auto clear time GENERAL INFORMATION Parameters 0 e OFF 1 e 30 sec. 5 e 10 sec. Preheat mode 0 e OFF 1 e 30 sec. Auto power shut-off timer * 1 e 30 min. 2 e 60 min.
USER PROGRAMS Settings for auditing accounts Settings of user programs No. 10 to 15 varies with the program number. For setting of all programs, first follow steps 1 to 3 in “Setting the user programs” on page 37 to select a program. (1. Press the light ( ) key for more than 5 seconds. 2. Enter a program number (10 to 15) using the numeric keys. 3. Press the START key.) Then follow the appropriate instructions for the program. Program No.
USER PROGRAMS Program No. 12: Account number change Program No. 12 is used to change account numbers. When program No. 12 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “12E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37. 1. Use the copy ratio display ( number to be changed. ● 2. 4. key to advance through the account numbers. Press the START key. ● 3.
USER PROGRAMS Program No. 14: Number of copies per account Program No. 14 is used to display the total number of copies made against each account number. When program No. 14 is entered, an account number will appear in the copy quantity display. ● If no account number has been registered, “14E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37. 1. Use the copy ratio display ( number. ● 2.
USER PROGRAMS Program No. 15: Resetting account Program No. 15 is used to reset all accounts or to reset any desired individual account. When program No. 15 is entered, “0” will blink on the right side of the copy quantity display. ● If no account number has been registered, “15E” will appear in the copy quantity display. Press the key. The copier will return to step 2 on page 37. 1. To reset an individual account, press the 0 key. To reset all accounts, press key 1. 2. Press the START key. 3.
POWER SAVE MODES The copier has two power save modes to reduce overall power consumption thereby reduce the cost of operation. In addition, these modes conserve natural resources and help reduce environmental pollution. The two power save modes are preheat mode and auto power shut-off mode. ● User programs The preheat activation time and the auto power shut-off time have been preset at the factory to 90 sec. for preheat mode and 30 min. for auto power shut-off mode.
POWER SAVE MODES Setting the power save modes The time that elapses before the copier enters a power save mode after any operation is made can be set manually. This time is set with user program No. 2 for the preheat mode and user program No. 3 for the auto power shut-off mode. For these settings, see page 37. ● The copier will enter the preheat mode first and then the auto power shutoff mode after a preset time has elapsed when no copier operation has been made.
USER MAINTENANCE Proper care is essential for clean, sharp copies. Please take a few minutes to regularly clean your copier. Original table and platen cover Stains or dirt on the original table or platen cover will also be copied. Wipe the original table and platen cover with a soft, clean cloth. ● If necessary, dampen the cloth with water. Do not use thinner, benzene, or similar volatile cleaning agents. ● If an optional single pass feeder is installed, wipe the scanning window on the original table.
COPIER TROUBLE? Problem Solution ● Copier plugged in? Plug the copier into a grounded outlet. See page 8. ● Power switch ON? Turn the power switch ON. See page 14. Copies are too dark or too light. ● Copy density properly adjusted? See pages 14 and 26. Blank copies ● Is the original placed face down? Place the original face down on the original table. ● Paper too heavy? Use copy paper within the specified range. See page 49. ● Paper damp? Replace with dry copy paper.
COPIER TROUBLE? Problem Copies are smudged or dirty. Solution Clean regularly. See page 45. ● Original smudged or blotchy? Use a clean original. ● Is the Maintenance is required. Contact your SHARP service centre as soon as possible. ● Is the COPY indicator off? Use the COPY/FAX key to select the COPY mode. See Note below. ● Is copying, printing or facsimile printing being performed? Set the paper size after copying, printing or facsimile printing is complete.
COPIER TROUBLE? Problem Power is on but copying is not possible. Lighting fixture flickers. Solution ● Is blinking in the copy quantity display? The TD cartridge is not installed. Install the TD cartridge. ● Is steadily lit in the copy quantity display? Side cover(s) is open. Close the front and side covers securely. ● Is the indicator blinking? The TD cartridge must be replaced. See page 27, TD CARTRIDGE REPLACEMENT. ● Is the indicator blinking? A misfeed has occurred.
SUPPLIES Types and sizes of copy paper * Size Weight Capacity (80 g/m2 paper) Paper tray A5* to A3 56 to 80 g/m2 250 sheets Bypass tray Ordinary paper: A6 to A3 Envelopes: International DL (110 x 220 mm) International C5 (162 x 229 mm) Commercial 10 (4-1/8" x 9-1/2") 56 to 128 g/m2** (Ordinary paper) 100 sheets Special paper Transparency film, labels, envelopes*** A5 copy paper can be used in the uppermost paper tray but cannot be used in other trays (in optional paper feed units).
SUPPLIES Genuine supplies statement Standard supplies for this copier that are to be replaced by the user are copy paper, TD cartridge, and drum cartridge. For best copying results, be sure to use only SHARP products. Only genuine SHARP consumables carry the Genuine Supplies label. GENUINE SUPPLIES Proper storage 1. GENERAL INFORMATION 2. Store the supplies in a location that is: ● clean and dry, ● at a stable temperature, ● not exposed to direct sunlight.
SPECIFICATIONS Copy system Dry, electrostatic transfer Originals Sheets, bound documents Original sizes Max. A3 Copy sizes Max. A3 Min. A6 Image loss: Max. 4 mm (leading and trailing edges) Max. 4 mm (along other edges in total) Copying speed (at 100% copy ratio) 16 copies/min. (A4) 12 copies/min. (A4R) 10 copies/min. (B4) 9 copies/min. (A3) Continuous copy Max. 99 copies; subtractive counter First-copy time 7.2 sec. (except in a power save mode) Warm-up time Approx. 35 sec.
SPECIFICATIONS Overall dimensions (with bypass tray folded) 590 mm (W) x 531 mm (D) Weight Approx.
OPTIONAL EQUIPMENT CONTENTS ● ● ● Page 54 55 55 55 56 57 58 58 59 61 63 65 OPTIONAL EQUIPMENT ● SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . SINGLE PASS FEEDER (AR-SP2) . . . . . . . . . . . . . . . . . . . . . . ● Part names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ● Using the SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SYSTEM CONFIGURATION A number of options are available for the copier which allow you to configure a copier system to meet your particular needs. The options include the following. Single pass feeder (AR-SP2) Electronic sorting kit (AR-EB3) Facsimile expansion kit (AR-FX2)* Printer expansion kit (AR-PB8)* PS2 expansion kit (AR-PS1)* LCD panel kit (AR-PA1)* Job separator tray kit (AR-TR2)* * These options are not used for the copier operation. For description of these options, see their separate manuals.
SINGLE PASS FEEDER (AR-SP2) The single pass feeder (SPF) holds up to 30 originals for automatic feeding. PART NAMES Original guides Document feeder tray Left feeding roller cover Exit area Right feeding roller cover Weight: 56 to 90 g/m2 Size: A5 to A3 Capacity: Up to 30 sheets provided the total aggregate thickness does not exceed 4 mm Detectable original sizes A5, A4, A4R, B4, A3 Power supply Drawn from the copier Weight Approx. 5.
SINGLE PASS FEEDER (AR-SP2) Using the SPF ● ● ● Be sure to remove any staples or paper clips from the originals. Damaged or crumpled originals may misfeed in the SPF. It is recommended that these originals be copied from the original table. For best feeding of originals which have binding holes punched into them, insert them so that the holes are positioned to the right or along the side guides.
SINGLE PASS FEEDER (AR-SP2) Misfeed removal If an original misfeed occurs in the SPF, the copier will stop and the red indicator which indicates an original misfeed will blink. A B C Location A Left feeding roller cover Location B Right feeding roller cover 2 3 4 If the misfed original cannot be removed in steps 1 and 2, remove the misfed original from the exit area. Open the document feeder cover and rotate the roller in the direction indicated by the arrow if needed.
ELECTRONIC SORTING KIT (AR-EB3) If an electronic sorting kit (AR-EB3) is installed, the copier can perform several additional useful functions. These functions are 2 in 1 and 4 in 1, erase, margin shift, and sort/group functions. Also, rotation copying can be performed and a multiple number of originals can be scanned and stored into the memory. The memory can be expanded by adding commercially available memories recommended by SHARP. For details, contact your dealer.
ELECTRONIC SORTING KIT (AR-EB3) Sort/group If an optional electronic sorting kit is installed, the copier will have two sorter modes for different copying jobs: one sorts copies into sets matching the sequence of the originals and the second groups copies by originals. The sort/group feature cannot be used with the dual page copy feature. To change the SORT/GROUP mode, press the SORT/GROUP key to select the desired mode.
ELECTRONIC SORTING KIT (AR-EB3) Copying in the sort mode When copying in the sort mode, the original image will be stored in the copier memory each time an original is scanned and copying will start after all originals have been scanned. To copy in the sort mode, an optional single pass feeder (AR-SP2) is needed. Electronic sorting kit (AR-EB3) 1 Set the originals face up in the document feeder tray. 2 Press the SORT/GROUP key to select the SORT mode.
ELECTRONIC SORTING KIT (AR-EB3) 2 in 1 or 4 in 1 2 in 1 copying Pattern Pattern Pattern Pattern 4 in 1 copying Pattern Pattern The 2 in 1 or 4 in 1 feature is used to copy 2 or 4 originals, collectively in a specified order, onto one sheet. To use these features, an optional single pass feeder (AR-SP2) is needed. ● These features cannot be used with the dual page copying, XY zoom, erase, or margin shift features. ● Copies can be made with or without the border lines shown in the illustration.
ELECTRONIC SORTING KIT (AR-EB3) 4 Electronic sorting kit (AR-EB3) 5 6 OPTIONAL EQUIPMENT 62 Enter the desired pattern number using a numeric key. ● The entered number will blink in the copy quantity display. For layout pattern numbers, see the previous page. Press the START key. ● The entered number will light up steadily. Press the 2 IN 1 / 4 IN 1 key to complete the selection. ● The copy ratio will be calculated automatically.
ELECTRONIC SORTING KIT (AR-EB3) Erase This copier has an edge erase mode and a centre erase mode. Edge erase A A Centre erase AB AB ● Edge erase can be used to eliminate shadow lines around the edges of copies caused when thick paper or a book is used as an original. ● Centre erase can be used to eliminate the shadow produced by the bindings of bound documents.
ELECTRONIC SORTING KIT (AR-EB3) Electronic sorting kit (AR-EB3) OPTIONAL EQUIPMENT 64 4 Set the number of copies. 5 Press the START key.
ELECTRONIC SORTING KIT (AR-EB3) Margin shift Original Copy The MARGIN SHIFT feature automatically shifts the text or image to the right to increase the left margin by approximately 9 mm. ● This feature cannot be used with the 2 in 1 or 4 in 1 feature. Expanded margin Margin is expanded here. 1 Place the original on the original table and close the platen cover. ● If an optional single pass feeder (SPF) is installed, it can also be used for this feature.
250-SHEET PAPER FEED UNIT (AR-DE5) 2x250-SHEET PAPER FEED UNIT (AR-DE6) These paper feed units provide the convenience of increased paper capacity for the copier and a greater choice of paper sizes readily available for copying. The AR-DE5 contains one 250-sheet paper tray and the AR-DE6 contains two 250-sheet paper trays.
250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6) Misfeed removal The copier will stop when a misfeed occurs. The misfeed ( ) indicator and the red indicator which indicates the paper feed unit will blink. 1 Open the side cover of the paper feed unit and remove the misfed paper. ● Be sure to perform this step before pulling out the paper trays. If not, the paper may be torn as the trays are opened. Gently lift and pull out the paper tray which was in use. Remove any misfed paper.
250-SHEET PAPER FEED UNIT (AR-DE5)/2x250-SHEET PAPER FEED UNIT (AR-DE6) Specifications AR-DE5 Copy paper size A4 to A3 Paper weight 56 to 80 g/m2 Paper capacity One paper tray with capacity for 250 sheets of paper Weight Approx. 4.
TRANSFER CHARGER CLEANING If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. 1 2 Charger cleaner 3 4 Turn the power switch off. Open the bypass tray. Lift slightly on the side cover and slide the cover out until it stops. Gently lift and pull out the paper tray and take the charger cleaner out by holding the tab.
DRUM CARTRIDGE LIFE To find out how many more copies can be made before the 30,000 mark is reached, follow the procedure described below. 1 2 Press and hold the light ( ) key for more than 5 seconds until all the alarm indicators ( , , , , and ) blink and “– –” appears in the copy quantity display. Press and hold down the CLEAR key for more than 5 seconds to find out how many more copies can be made. ● The number will appear in two steps, each with three digits.
INDEX 2 250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . . . 66 2 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 2x250-sheet paper feed unit . . . . . . . . . . . . . . . . . . . . . 66 4 4 in 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 A Auto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Automatic exposure adjustment . . . . . . . . . . . . . . . . . .
INDEX S Single pass feeder (SPF) . . . . . . . . . . . . . . . . . . . . . . . . Sort . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications – copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
S H A R P Date Issued:Nov. 1, 1998 MATERIAL SAFETY DATA SHEET MSDS No. F-00841 Section 1. Product Identification Product: AR-200DC/AR-200LT (Black Toner) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
S H A R P Date Issued :Nov. 1, 1998 MATERIAL SAFETY DATA SHEET MSDS No. F-30841 Section 1. Product Identification Product AR-200DC/AR-200LD (Black Developer) Section 2. Supplier’s Name and Address Sharp Corporation 22-22 Nagaike-cho, Abeno-ku, Osaka, Japan Local suppliers are listed below. Please contact the nearest supplier for additional information. (Country) U.S.A. Canada United Kingdom Section 3. Ingredients Ingredients Iron powder Styrene-Acrylate copolymer Carbon black Section 4.
Section 6. Physical Chemical Characteristics Boiling / Melting Point: Vapor Pressure: Vapor Density: Evaporation Rate: Appearance: Odor: Section 7. Not applicable Not applicable Not applicable Not applicable Fine powder Odorless Not applicable >350°C (LEL); Not applicable (UEL); Not applicable CO2, dry chemical, foam or water None This material has no unusual fire or explosion hazards.
Warning! This product is a class A product. If it is operated in households, offices or similar surroundings, it can produce radio interferences at other appliances, so that the user has to take adequate countermeasures. CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.
In some areas, the “POWER” switch positions are marked “ I ” and “ ” on the copier instead of “ON” and “OFF”. The symbol “ ” denotes the copier is not completely de-energized but in a stand-by condition at this “POWER” switch position. If your copier is so marked, please read “ I” for “ON” and “ ” for “OFF”. Caution! For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible.
AR-160/AR-161 SHARP ELECTRONICS (U.K.) LTD.
