ページ ２００２年 月 日 水曜日 午前 時５５分 MODEL AR-122E N AR-123E DIGITAL LASER COPIER/PRINTER OPERATION MANUAL Page INTRODUCTION LOADING PAPER MAKING COPIES SPECIAL FUNCTIONS MAINTENANCE TROUBLESHOOTING THE UNIT OPTIONAL EQUIPMENT INSTALLING THE SOFTWARE APPENDIX AR-122E N / AR-123E 4 7 11 18 21 26 32 38 67
ページ ２００２年 CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT 月 日 水曜日 午前 時５５分 VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLA KUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLA TAVALLA SAATTAA ALTISTAA KÄYTTÄJÄN TURVALLISUUSLUOKAN 1 YLITTÄVÄLLE NÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE. VARNING OM APPARATEN ANVÄNDS PÅ ANNAT SÄTT ÄN I DENNA BRUKSANVISNING SPECIFICERATS, KAN ANVÄNDAREN UTSÄTTAS FÖR OSYNLIG LASERSTRÅLNING, SOM ÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.
ページ ２００２年 月 日 水曜日 午前 時５５分 CAUTIONS Caution label on the unit The label ( ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using Follow the cautions below when using this unit. Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. • Do not look directly at the light source. Doing so may damage your eyes. • Do not switch the unit rapidly on and off.
ページ ２００２年 月 日 水曜日 午前 時５５分 Cautions on handling Be careful in handling the unit as follows to maintain the performance of this unit. Do not drop the unit, subject it to shock or strike it against any object. Store spare toner cartridges in a cool dry place without removing from the package before use. • If they are exposed to direct sunlight or excessive heat, poor copies may result. Do not touch the photoconductive drum (green portion). • Scratches or smudges on the drum will cause dirty copies.
ページ ２００２年 月 日 水曜日 午前 時５５分 CONTENTS 1 INTRODUCTION USING THE MANUAL ................... 4 PART NAMES ............................... 5 OPERATION PANEL..................... 6 2 LOADING PAPER PAPER........................................... 7 LOADING THE PAPER TRAY....... 8 BYPASS FEED (including special paper).............. 10 3 MAKING COPIES COPY FLOW ............................... 11 CONNECTING THE POWER CORD .......................................... 12 ORIGINAL PLACEMENT.............
ページ ２００２年 1 月 日 水曜日 午前 時５５分 INTRODUCTION This chapter provides basic information for using the unit. USING THE MANUAL The operation manual contains explanations of how to operate the unit, important considerations, and maintenance procedures. To get the most out of the unit, please read the operation manual. Please keep the operation manuals in a suitable location that will allow for convenient future reference.
ページ ２００２年 月 日 水曜日 午前 時５５分 PART NAMES 1 Original cover 1 2 5 6 3 8 9 10 4 11 12 7 Single bypass 13 5 14 3 15 Photoconductive drum Toner cartridge 1 2 3 4 5 6 7 8 9 Original table Operation panel Front cover Paper tray Side cover Side cover open button Bypass paper guides Paper output tray Paper output tray extension 10 11 12 13 14 15 Power switch Handle Power cord socket Fusing unit release lever Transfer charger Charger cleaner 5
ページ ２００２年 月 日 水曜日 午前 時５５分 OPERATION PANEL Inch system 1 2 3 Exposure mode selector key and indicators Use to sequentially select the exposure modes: AUTO, MANUAL or PHOTO. Selected mode is shown by a lit indicator. (p.15) Light and dark keys and indicators Use to adjust the MANUAL or PHOTO exposure level. Selected exposure level is shown by a lit indicator. (p.15) Use to start and terminate user program setting. (p.19) Alarm indicators Developer replacement required indicator (p.
ページ 2 ２００２年 月 日 水曜日 午前 時５５分 LOADING PAPER Follow the steps below to load paper into the tray. PAPER For best results, use only paper recommended by SHARP. Type of paper feeding Paper tray Type of media Standard paper Single bypass Standard paper and thick paper Size Weight A4 (210mm x 297mm) A5 (148mm x 210mm) B5 (182mm x 257mm) Letter (8-1/2" x 11") Legal (8-1/2" x 14") Invoice (5-1/2" x 8-1/2") 56g/m2 to 80g/m2 (15 lbs. to 21 lbs.
ページ ２００２年 月 日 水曜日 午前 時５５分 LOADING THE PAPER TRAY 1 Raise the handle of the paper tray and pull the paper tray out until it stops. 2 Adjust the paper guides on the paper tray to the copy paper width and length. Squeeze the lever of paper guide A and slide the guide to match with the width of the paper. Move paper guide B to the appropriate slot as marked on the tray. Paper guide B 3 Paper guide A Fan the paper and insert it into the tray. Make sure the edges go under the corner hooks.
ページ 4 ２００２年 月 日 水曜日 午前 時５５分 Gently push the paper tray back into the unit. • After loading paper, to cancel the blinking without restarting copying, press the clear ( ) key. The in the display will go out and the start ( ) indicator will light up. • Be sure that paper is free of rips, dust, wrinkles, and curled or bent edges. • Make sure all the paper in the stack is the same size and type.
ページ ２００２年 月 日 水曜日 午前 時５５分 BYPASS FEED (including special paper) The single bypass can be used to feed standard paper, transparency film, labels, envelopes, and other special purpose paper. Paper measuring from A6 to A4 (3-1/2" x 5-1/2" to 8-1/2" x 14") and in the weight range of 52g/m2 to 128g/m2 (14 lbs. to 34.5 lbs.) can be used in this tray. (For paper weighing from 104g/m2 to 128g/m2 (28 lbs. to 34.5 lbs.), A4 (8-1/2" X 11") is the maximum size.) • The single bypass can hold one sheet of paper.
ページ ２００２年 3 月 日 水曜日 午前 時５５分 MAKING COPIES This chapter explains basic and other copying functions. The unit is equipped with a one-page memory buffer. This memory allows the unit to scan an original once only and make up to 99 copies. This feature improves workflow, reduces operation noise from the copier, and provides higher reliability by reducing wear and tear on the scanning mechanism.
ページ ２００２年 月 日 水曜日 午前 時５５分 Do not insert paper in the single bypass when a copy job from the paper tray is in progress. This will cause a misfeed. CONNECTING THE POWER CORD If you use the unit in a country other than the country where the unit was purchased, you will need to make sure that your local power supply is compatible with your model. If you plug the unit into an incompatible power supply, irreparable damage to the unit will result.
ページ ２００２年 月 日 水曜日 午前 時５５分 About the scan head The scan head lamp remains on constantly when the unit is in the ready condition (when the start ( ) indicator is illuminated). The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not indicate unit trouble.
ページ ２００２年 月 日 水曜日 午前 時５５分 ORIGINAL PLACEMENT • The original table can read up to A4 (8-1/2" x 14") original. • Image loss 4mm (5/32") can occur at the leading and trailing edges of the copies. Also image loss 4.5mm (11/64") in total can occur along the other edges of the copies. • When copying a book or an original which has been folded or a crumpled original, press down the original cover lightly. If the original cover is not securely closed, the copies may be striped or blurred.
ページ ２００２年 月 日 水曜日 午前 時５５分 SET THE COPY QUANTITY Set the number of copies using the two copy quantity ( from the original table, or from the SPF if installed. , ) keys when copying • Press the clear ( ) key to clear an entry if a mistake is made. • A single copy can be made with the initial setting, i.e., when "0" is displayed. • Press the right copy quantity key to set the unit digit from 0 to 9. This key will not change the tens digit.
ページ ２００２年 月 日 水曜日 午前 時５５分 Automatic exposure adjustment This automatic exposure level will remain in effect until you change it again by this procedure. The automatic exposure level can be adjusted to suit your copying needs. This level is set for copying from the original table and copying from the SPF respectively. 16 1 When adjusting the level for copying from the original table, make sure that no original is left in the original feeder tray.
ページ ２００２年 月 日 水曜日 午前 時５５分 REDUCTION/ENLARGEMENT/ZOOM Three preset reduction ratios and two enlargement ratios can be selected. The zoom function enables copy ratio selection from 25% to 400% in 1% increments. 1 Set the original and check the paper size. 2 Use the copy ratio selector key and/or ZOOM ( select the desired copy ratio. , ) keys to • To verify a zoom setting without changing the zoom ratio, press and hold down the copy ratio display (%) key.
ページ 4 ２００２年 月 日 水曜日 午前 時５５分 SPECIAL FUNCTIONS This chapter describes the special functions of this unit. Use these functions as needed. DESCRIPTION OF SPECIAL FUNCTIONS Toner save mode (page 18) Reduces toner consumption by approximately 10%. Power save modes (page 19) The unit has two power save modes of operation: preheat mode and auto power shut-off mode.
ページ ２００２年 月 日 水曜日 午前 時５５分 2 Press and hold down the exposure mode selector key for approximately 5 seconds. The MANUAL ( ) indicator will go out and the PHOTO ( ) indicator will begin to blink. The light and dark indicator marked "5" will light up, indicating the standard toner mode is active. 3 To enter the toner save mode, press the light ( ) key. The light and dark indicator marked "1" will light up, indicating the toner save mode is selected. 4 Press the exposure mode selector key.
ページ Program No. ２００２年 月 日 水曜日 午前 時５５分 Mode Parameters 1 Auto clear time 0 *3 OFF, 1 10sec., 2 30sec. 60sec., 4 90sec., 5 120sec. 2 Preheat mode *0 3 Auto power shut- off timer 0 3 2min., *1 30min., 4 4 Stream feeding mode 0 OFF, *1 ON 5 Auto power shut- off mode 0 OFF, *1 ON 6 Resolution of AUTO & MANUAL mode *0 30sec., 1 300dpi, 1 60sec., 2 90sec. 5min., 2 15min., 60 min., 5 120min. 600dpi * Factory default settings are indicated with an asterisk (*). Program No.
ページ 5 ２００２年 月 日 水曜日 午前 時５５分 MAINTENANCE This chapter describes how to replace the toner cartridge and how to clean the unit. Be sure to use only genuine SHARP parts and supplies. For best copying results, be sure to use only SHARP Genuine Supplies which are designed, engineered, and tested to maximise the life and performance of SHARP copiers. Look for the Genuine Supplies label on the toner package.
ページ 3 ２００２年 月 日 水曜日 午前 時５５分 Gently pull the toner cartridge out while pressing the lock release lever. Toner cartridge lock release lever • After removing the toner cartridge, do not shake it or tap on it. Doing so may cause toner to leak from the cartridge. Put the old cartridge immediately in the bag contained in the box of the new cartridge. • Dispose of the old toner cartridge in accordance with local regulations. 4 Remove the toner cartridge from the bag.
ページ 6 ２００２年 月 日 水曜日 午前 時５５分 Close the front cover and then the side cover by pressing the round projections near the side cover open button. The indicator ( ) will go out and the start ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.
ページ ２００２年 月 日 水曜日 午前 時５５分 CLEANING THE UNIT Proper care is essential in order to get clean, sharp copies. Be sure to take a few minutes to regularly clean the unit. • Before cleaning, be sure to turn the power switch off and remove the power cord from the outlet. • Do not use thinner, benzene or other volatile cleaning agents. Doing so may cause deformation, discoloration, deterioration or malfunction. Cabinet Wipe the cabinet with a soft, clean cloth.
ページ ２００２年 月 日 水曜日 午前 時５５分 Transfer charger If copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean the charger using the following procedure. 1 Turn the power switch off. (p.13) 2 Open the side cover while pressing the side cover open button. 3 Take the charger cleaner out by holding the tab. Set the charger cleaner onto the right end of the transfer charger, gently slide the cleaner to the left end, and then remove it. Repeat this operation two or three times.
ページ 6 ２００２年 月 日 水曜日 午前 時５５分 TROUBLESHOOTING THE UNIT This chapter describes misfeed removal and troubleshooting. TROUBLESHOOTING If any problem occurs, check the list below before contacting your authorised service representative. Problem Solution Page Plug the unit into a grounded outlet. 12 Turn the power switch on. 12 Unit does not Gently close the side cover. 23 operate. Gently close the front cover and then 23 close the side cover.
ページ ２００２年 月 日 水曜日 午前 時５５分 STATUS INDICATORS When the following indicators light up or blink on the operation panel or the following alphanumeric codes appear in the display, solve the problem immediately referring to both the table below and the relevant page. Be sure to use only genuine SHARP parts and supplies.
ページ ２００２年 月 日 水曜日 午前 時５５分 MISFEED REMOVAL When the misfeed ( ) indicator blinks or stop because of a misfeed. 1 blinks in the display, the unit will Open the side cover, in that order. To open the side cover, see "TONER CARTRIDGE REPLACEMENT" (p.21). 2 Check the misfeed location. Remove the misfed paper following the instructions for each location in the illustration below. If the misfeed ( ) indicator blinks, proceed to "A: Misfeed in the paper feed area" (p.29).
ページ ２００２年 月 日 水曜日 午前 時５５分 A: Misfeed in the paper feed area 1 Gently remove the misfed paper from the paper feed area as shown in the illustration. When the misfeed ( ) indicator blinks, and the misfed paper is not seen from the paper feed area, pull out the paper tray and remove the misfed paper. If the paper cannot be removed, proceed to "B: Misfeed in the fusing area". The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury.
ページ 2 ２００２年 月 日 水曜日 午前 時５５分 Gently remove the misfed paper from under the fusing unit as shown in the illustration. If the paper cannot be removed, proceed to "C: Misfeed in the transport area". The fusing unit is hot. Do not touch the fusing unit when removing misfed paper. Doing so may cause a burn or other injury. • Do not touch the photoconductive drum (green portion) when removing the misfed paper. Doing so may cause smudges on copies.
ページ 4 ２００２年 月 日 水曜日 午前 時５５分 Raise the fusing unit release lever, close the front cover and then close the side cover by pressing the round projections near the side cover open button. The misfeed ( ) indicator will go out and the start ( ) indicator will light up. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the covers may be damaged.
ページ 7 ２００２年 月 日 水曜日 午前 時５５分 OPTIONAL EQUIPMENT SYSTEM CONFIGURATION A number of options are available for the unit which allow you to configure a system to meet your particular needs. The options include the following. Printer/Scanner Expansion Kit (AL-12PK) Single pass feeder (AR-SP5) AR-122EN 250-sheet paper feed unit (AR-D16) AR-123E PRINTER/SCANNER EXPANSION KIT (AL-12PK) A printer function and scanner function can be added to the unit by installing the AL12PK.
ページ ２００２年 月 日 水曜日 午前 時５５分 Using the SPF The SPF is designed to hold up to 30 originals measuring from A5 to A4 (5-1/2" x 8-1/2" to 8-1/2" x 14") and weighting from 52g/m2 to 90g/m2 (14 lbs. to 23.9 lbs.). • Before feeding originals in the original feeder tray, be sure to remove any staples or paper clips from them. • Before placing curled or wavy originals into the original feeder tray, be sure to flatten them. If not, original misfeeds may result.
ページ ２００２年 月 日 水曜日 午前 時５５分 SPF roller SPF scanning window Misfeed in the SPF If a misfeed occurs when using the SPF, a number may appear in the display after a minus sign. This indicates the number of the originals that must be returned to the original feeder tray after a misfeed. Return the required number of originals. Then this number will disappear when copying is resumed or the clear ( ) key is pressed.
ページ ２００２年 月 日 水曜日 午前 時５５分 (B) Open the SPF and rotate the roller rotating knob to remove the misfed original from the exit area. If the misfed original cannot be easily removed, proceed to (C). Roller rotating knob (C) If the original does not move easily into the exit area, remove it in the direction of the arrow while rotating the knob. A number may appear in the display after a minus sign, indicating the number of the originals that must be returned to the original feeder tray.
ページ ２００２年 月 日 水曜日 午前 時５５分 250-SHEET PAPER FEED UNIT (AR-D16) The paper feed unit provide the convenience of increased paper capacity for the unit and a greater choice of paper size readily available for copying. The procedures for loading paper in the paper tray of paper feed unit and changing the paper size are same as for the paper tray in the unit. See "LOADING THE PAPER TRAY" (p.8). Tray Lower side cover Selecting the tray Press the tray select ( ) key.
ページ ２００２年 月 日 水曜日 午前 時５５分 4 Click the "Utility" tab. 5 Select "Two trays" for "Input tray option", and click "OK". 6 The printer driver closes. This completes the settings needed to use the AR-D16. Misfeed in the lower paper feed area If the unit is turned on with the lower side cover open, the misfeed ( ) indicator will blink. In this case, close the lower side cover. The misfeed ( ) indicator will go out. 1 Open the lower side cover (under the single bypass) and remove the misfed paper.
ページ 8 ２００２年 月 日 水曜日 午前 時５５分 INSTALLING THE SOFTWARE The procedure for installing the software for the optional Printer/Scanner Expansion Kit (AL-12PK) and the operation of the printer/scanner is explained here. Information on how to use the online manual is also provided. For the procedure for installing the AL-12PK, see the setup guide that accompanies the AL-12PK. Illustrations of driver screens and other computer screens show the screens that appear in Windows XP Home Edition.
ページ ２００２年 月 日 水曜日 午前 時５５分 HARDWARE AND SOFTWARE REQUIREMENTS Check the following hardware and software requirements in order to install the software. Computer type IBM PC/AT or compatible computer equipped with a USB1.1*1 or bi-directional parallel interface (IEEE 1284) Operating system*2 Windows 95, Windows 98, Windows Me, Windows NT Workstation 4.
ページ ２００２年 月 日 水曜日 午前 時５５分 Flow of installation Refer to the following table and then begin installation. Operating system Windows XP Windows 98 Interface Reference pages for how to install USB/ Parallel USB Installing onto Windows XP (USB/parallel interface) (p.41) Installing onto Windows 98/Me/2000 (USB interface) (p.45) Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel interface) (p.48) Installing onto Windows 98/Me/2000 (USB interface) (p.45) Installing onto Windows 95/98/Me/NT4.
ページ ２００２年 月 日 水曜日 午前 時５５分 INSTALLING THE SOFTWARE The following term is used in this section. MFP Means the unit as a printer and scanner. • For this description, it is assumed that the mouse is configured for right hand operation. • To print or scan, the MFP must be in the online state. • The scanner feature only works when using a USB interface cable. • If any error message appears, solve the problem following the instructions on the screen.
ページ ２００２年 月 日 水曜日 午前 時５５分 • If you are using the parallel interface connection, do not select the Button Manager checkbox because this feature is not supported with the parallel interface. • If the following screen appears, click the "OK" button. Review the contents in "BEFORE INSTALLATION" (p.39), and then select only appropriate the software packages to be installed. 5 Review the software packages to be installed on the screen, and then click the "Start" button.
ページ 7 2 3 4 5 日 水曜日 午前 時５５分 After confirming the message in the "Welcome" window, click the "Next" button. Read the message in the "Please read the following information." window, and then click the "Next" button. When a message appears that lets you specify the location for the software to be installed, click the "Next" button. If the program displays "Do you want the Button Manager added to Windows Startup?", check "Yes" and click the "OK" button. The setup program will start to copy the files.
ページ 10 ２００２年 月 日 水曜日 午前 時５５分 Make sure that the power of the MFP is turned on, and then connect the USB interface cable or parallel interface cable. (p.65) Windows will detect the MFP and the Plug and Play screen will appear. If you are using Windows XP with the parallel interface, go to step 12. 11 Begin installation of the scanner driver. 1 2 3 12 44 "SHARP AR-xxxx" (where xxxx is the model name of your MFP) will appear in the "Found New Hardware Wizard" dialog box.
ページ ２００２年 月 日 水曜日 午前 時５５分 Installing onto Windows 98/Me/2000 (USB interface) Before starting the installation, make sure the USB interface cable is not connected to the MFP. 1 Insert the supplied CD-ROM into your CD-ROM drive. 2 Double-click "My Computer" ( CD-ROM ( ) icon. ), and then double-click the When any of "Hardware Found", or "Found New Hardware Wizard" messages appear during the software installation, be sure to click the "Cancel" button. 3 Double-click the "setup" ( ) icon.
ページ 6 2 3 4 5 日 水曜日 午前 時５５分 After confirming the message in the "Welcome" window, click the "Next" button. A dialog box appears asking you to verify that the interface cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button. Click the "Next" button in the dialog box showing the files to be copied for installation of the MFP driver. The setup program will start to copy the files.
ページ 8 月 日 水曜日 午前 時５５分 Begin installation of the Sharpdesk (This step will start if it was selected in step 4). 1 2 3 4 5 9 ２００２年 After confirming the message in the "Welcome to Sharpdesk installation" window, click the "Next" button. Read the message in the "Information" window, and then click the "Next" button. When the "Choose Destination Location" window appears, click the "Next" button. When the "Select Program Folder" window appears, click the "Next" button.
ページ ２００２年 月 日 水曜日 午前 時５５分 Installing onto Windows 95/98/Me/NT4.0/2000 (Parallel interface) Before starting the installation, make sure the USB or parallel interface cable is not connected to the MFP. 1 Insert the supplied CD-ROM into your CD-ROM drive. 2 Double-click "My Computer" ( CD-ROM ( ) icon. ), and then double-click the When any of "Hardware Found", or "Found New Hardware Wizard" messages appear during the software installation, be sure to click the "Cancel" button.
ページ 7 ２００２年 月 日 水曜日 午前 時５５分 Copying files for MFP driver installation and parallel interface setup (This step will start if it was selected in step 4). 1 2 3 4 After confirming the message in the "Welcome" window, click the "Next" button. A dialog box appears asking you to verify that the USB or parallel interface cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button.
ページ 8 月 日 水曜日 午前 時５５分 Begin installation of the Sharpdesk (This step will start if it was selected in step 4). 1 2 3 4 5 9 ２００２年 After confirming the message in the "Welcome to Sharpdesk installation" window, click the "Next" button. Read the message in the "Information" window, and then click the "Next" button. When the "Choose Destination Location" window appears, click the "Next" button. When the "Select Program Folder" window appears, click the "Next" button.
ページ ２００２年 月 日 水曜日 午前 時５５分 INDICATORS ON THE OPERATION PANEL The ONLINE indicator and the start ( scanner. ) indicator indicate the state of the printer or SCANNER indicator ONLINE indicator Start indicator Power save indicator Start indicator On: Indicates the unit is ready for copying or scanning is being performed. Blinking: The indicator blinks in the following situations: • When a print job is interrupted. • When reserving a copy job.
ページ ２００２年 月 日 水曜日 午前 時５５分 USING THE PRINTER MODE For problems with the printer function, see the online manual or the help file for the driver. Opening the printer driver from the start menu Open the printer driver setup screen by the method shown below. 1 Click the "start" button. 2 Click "Control Panel", select "Printers and Other Hardware", and then click "Printers and Faxes". On Windows 95/98/Me/NT4.0/2000, select "Settings" and click "Printers".
ページ 4 ２００２年 月 日 水曜日 午前 時５５分 Specify the print settings including the number of copies, media type, and print quality, and then click the "Print" button to start printing. On Windows 95/98/Me/NT 4.0, click the "OK" button to start printing. For details on print settings, see the online manual or the help file for the printer driver. When using the single bypass After appears in the display, wait until the Paper feed location indicator for the single bypass illuminates and insert the paper.
ページ ２００２年 月 日 水曜日 午前 時５５分 USING THE SCANNER MODE The scanner driver for this unit includes an STI (Still image) driver and WIA (Windows Image Acquisition) driver. You can install software that supports the STI driver and WIA driver to enable scanning using the operation panel of the unit. For problems with the scanner function, see the online manual or the help file for the driver.
ページ ２００２年 月 日 水曜日 午前 時５５分 Windows 98/Me/2000 To scan directly into an application using the Button Manager on Windows 98, Windows Me and Windows 2000. Set the Event Manager properties to send only to Button Manager as shown below. 1 Click the "Start" button, select "Control Panel" from "Settings", and open "Scanners and Cameras" in start menu. In Windows Me, it occasionally happens that the "Scanners and Cameras" icon does not appear immediately after installation of the MFP driver is completed.
ページ ２００２年 月 日 水曜日 午前 時５５分 Scan Parameter Setting Dialog Box After you have completed the Button Manager settings in Windows, configure the scan settings in Button Manager. To configure the scan settings in Button Manager, right click the ( ) icon in the Taskbar and select "Setting" from the menu that appears. For details on configuring the scan settings in Button Manager, see the online manual or the help file.
ページ ２００２年 月 日 水曜日 午前 The settings for the Windows Event Manager for the SHARP AR-xxxx (where xxxx is the model name of your unit) device allow the user to take advantage of the Sharp Button Manager to take control of events from Windows and send scanned images to any application that can be selected in Button Manager.
ページ ２００２年 月 日 水曜日 午前 時５５分 Using the SCANNER key to begin scanning • Scanning is not possible during a copy job. • If the SCANNER ( ) key is pressed during a print job, the scan job will be stored. 1 Press the SCANNER ( ) key. The unit enters scan mode. 2 Place the original you wish to scan on the original table. 3 Press the right copy quantity key to display the number of the application that you wish to use for scanning.
ページ 4 ２００２年 Press the start ( 月 日 水曜日 午前 時５５分 ) key. Scanning will start and the scanned data will be transferred to the application. • If the following screen appears, select Button Manager and click "OK". Button Manager starts and the application associated with Button Manager starts. If you want only Button Manager to start in this case, set up Button Manager for use in Windows as explained in "Setting up the Button Manager" (p.54).
ページ 3 ２００２年 月 日 水曜日 Select "SHARP Personal MFP series", and click the "Select" button. 午前 時５５分 Click here If you use more than one scanning device, select the scanner you want to use through the application. The method for accessing the "Select Scanner" option, depends upon the application. For more information, see the online manual or the help file of your application. 4 Select "Acquire Image" from the "File" menu, or click the "Acquire" button ( ).
ページ ２００２年 月 日 水曜日 午前 時５５分 Scanning with the "Scanner and Camera Wizard" in Windows XP Windows XP includes as a standard feature an image scanning function. The procedure for scanning with the "Scanner and Camera Wizard" is explained here. To cancel scanning, click the "Cancel" button in the screen that is displayed. 1 Place the original you wish to scan on the original table.
ページ ２００２年 月 日 水曜日 午前 時５５分 HOW TO USE THE ONLINE MANUAL The online manual provides detailed instructions for operating the unit as the printer or scanner and a list of methods for dealing with printing or scanner problems. To access the online manual, your computer must have Acrobat Reader 5.0 or a later version. If it is not installed, refer to "Installing Acrobat Reader" (Next page). Contents of the online manual The contents of the online manual are as follows.
ページ 5 Click the ２００２年 月 日 水曜日 午前 時５５分 to read the online manual. To close the online manual, click the ( the window. ) button located at the top-right of • The online manual can be printed out using Acrobat Reader. SHARP recommends printing out the sections which you refer to regularly. • Refer to "Help" of Acrobat Reader for more details on the operation and function of Acrobat Reader. Installing Acrobat Reader 1 Turn on your computer. 2 Insert the CD-ROM into the CD-ROM drive.
ページ ２００２年 月 日 水曜日 午前 時５５分 USING OTHER INSTALLED DRIVERS If you use another GDI printer or a Windows Printing System printer, interference between printers may occur and printing may not be performed properly. To use another GDI printer or a Windows Printing System printer, you must change the port setting of the printer driver using the following procedure.
ページ ２００２年 月 日 水曜日 午前 時５５分 CONNECTING THE INTERFACE CABLE This unit includes both USB and parallel interface connectors. Interface cables for connecting the unit to your computer are not included with this unit. Please purchase the appropriate cable for your computer. Interface cable Parallel interface cable IEEE 1284-Shielded type bi-directional parallel interface cable (2 m (6 feet) Max.) USB interface cable Shielded twisted pair cable, high-speed transmission equivalent (2 m (6 feet) Max.
ページ ２００２年 月 日 水曜日 午前 時５５分 Connecting the parallel interface cable 66 1 Obtain an IEEE1284 shielded parallel interface cable. 2 Ensure that your computer and unit are turned off. 3 Insert the cable into the parallel interface connector located on the rear of the unit, and fasten with clasps. 4 Insert the other end of the cable into the interface connector of your computer.
ページ ２００２年 9 月 日 水曜日 午前 時５５分 APPENDIX SPECIFICATIONS Model AR-122E N / AR-123E Type Digital laser copier/printer, desk-top type Copy system Dry, electrostatic transfer Originals Sheets, bound documents Paper tray 250 sheets (Paper tray) 1 sheet (Single bypass) Paper output tray 100 sheets Original sizes Max. A4 (8-1/2" x 14") Original feed 1 sheet Copy size A6 to A4 (3-1/2" x 5-1/2" to 8-1/2" x 14") *1 Image loss Max. 4mm (5/32") *2 Max. 4.
ページ ２００２年 月 日 水曜日 Model Width Unit dimensions Depth Height 時５５分 AR-122E N / AR-123E 518mm (20.4") AR-122E N: 462.5mm (18.2") AR-123E: 492.5mm (19.4") 295.6mm (11.6") Operating conditions Temperature: 10°C to 30°C (50°F to 86°F) Humidity: 20% to 85% Noise level Sound Power Level LwA (1B=10dB) Copying: 6.0 [B], Standby: 3.7 [B] Sound Pressure Level LpA (bystander positions) Copying: 46 [dB (A)], Standby: 23 [dB (A)] Noise emission measurement in accordance with ISO 7779.
ページ ２００２年 月 日 水曜日 午前 時５５分 Optional equipment Printer/Scanner Expansion Kit (AL-12PK) Printing system Dry, electrostatic transfer Printing size A6 to A4 (3-1/2" x 5-1/2" to 8-1/2" x 14") *1 Print speed Max. 12 pages/min. (A4 or Letter) Continuous printing Max. 99 pages subtractive counter First-print time (Approximately) 9.
ページ ２００２年 月 日 水曜日 午前 時５５分 INDEX 2 Copy ratio selector key.................. 6, 17 250-Sheet paper feed unit ................. 36 D A Dark key ........................................ 6, 15 Developer replacement required indicator................................... 6, 27, 31 Developer required............................ 31 Display................................................. 6 Displaying total number of copies ..... 20 Acrobat Reader .................................
ページ ２００２年 月 日 水曜日 午前 時５５分 M R Maintenance indicator ............. 6, 27, 31 Making copies ................................... 11 MFP driver - Print Status Window ..................... 38 - Printer driver................................. 38 - Scanner driver .............................. 38 Misfeed indicator ..................... 6, 27, 28 Misfeed removal - Fusing area .................................. 29 - Paper feed area............................ 29 - SPF .......................................
ページ ２００２年 月 日 水曜日 午前 時５５分 INDEX BY PURPOSE Cleaning the unit - Cabinet ......................................... 24 - Original cover ............................... 24 - Original table ................................ 24 - SPF .............................................. 33 - Transfer changer .......................... 25 Connecting the interface cable - Parallel interface cable ................. 66 - USB interface cable...................... 65 Copying .............................................
ページ ２００２年 月 日 水曜日 午前 時５５分 SOFTWARE LICENSE PLEASE READ THIS LICENSE CAREFULLY BEFORE USING THE SOFTWARE. BY USING THE SOFTWARE, YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE. 1. License. The application, demonstration, system and other software accompanying this License, whether on disk, in read only memory, or on any other media (the "Software") and related documentation are licensed to you by SHARP.
ページ ２００２年 月 日 水曜日 午前 時５５分 6. Limited Warranty on Media. SHARP warrants the disks on which the Software is recorded to be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of purchase as evidenced by a copy of the receipt. The entire liability of SHARP and/or its Licensors and your exclusive remedy will be replacement of the disk which fails to meet the limited warranty provided by this Clause 6.
ページ MEMO ２００２年 月 日 水曜日 午前 時５５分
ページ MEMO ２００２年 月 日 水曜日 午前 時５５分
ページ ２００２年 月 日 水曜日 午前 時５５分 In some areas, the “POWER” switch positions are marked “I” and “ ” on the copier instead of “ON” and “OFF”. The symbol “ ” denotes the copier is not completely de-energized but in a stand-by condition at this “POWER” switch position. If your copier is so marked, please read “I” for “ON” and “ ” for “OFF”. Caution! For a complete electrical disconnection, pull out the main plug. The socket-outlet shall be installed near the equipment and shall be easily accessible.
ページ ２００２年 月 日 水曜日 午前 時５５分 SHARP CORPORATION Printed on Recycled Paper PRINTED IN CHINA KS 1 2002H TINSE0819QSZZ
