Service manual

AL-2030/2040CS/2050CS USER PROGRAM 11 - 3
11 2-SIDED COPY
MODE
1: HI-SPEED
2: NORMAL
• If the memory fills up when two-sided copying is performed, "NORMAL" can
be selected to make copying possible. However, "NORMAL" results in a
slower copying speed. Normally "HI-SPEED" is selected to enable fast two-
sided copying.
12 MARGIN WIDTH 1: 1/4"
2: 1/2"
3: 3/4"
4: 1"
• Use this setting to set the margin width.
13 MEM. FOR
PRINTER
1: 30%
2: 40%
3: 50%
4: 60%
5: 70%
• Use this to change the proportion of machine memory used for printer mode.
14 AUTO KEY
REPEAT
1: ON
2: OFF
• Use this setting to select whether or not holding down a key causes repeated
input of the key. For keys that normally cause a set value to decrease or
increase when held down (for example, the [ ] key ( ) or [ ] key
( )), this program can be used to have the set value not change when the
key is held down.
15 KEY PRESS TIME 1: NORMAL
2: 0.5 SEC.
3: 1.0 SEC.
4: 1.5 SEC.
5: 2.0 SEC.
• Use this setting to select how long a key must be pressed for the input to be
accepted.
By selecting a longer time, you can prevent settings from being changed by
the accidental pressing of a key.
16 KEY TOUCH
SOUND
1: LOW
2: HIGH
3: OFF
• This sets the volume of beep signals.
17 SOUND AT
DEFAULT
1: ON
2: OFF
• Use this to sound a beep when a base setting is selected.
18 TONER SAVE
MODE
1: ON
2: OFF
• This mode reduces toner usage by about 10% when copying. Toner save
mode is effective when the exposure mode is AUTO or TEXT.
19 AE LEVEL
ADJUST
1: SPF/RSPF
(Adjustment to
5 levels is possible.)
2: DOCUMENT GLASS
(Adjustment to
5 levels is possible.)
• This is used to adjust the exposure level.
• The automatic exposure level can be adjusted separately for the document
glass and the RSPF.
• For the procedure for adjusting the exposure and guidelines for numeric
values. The factory default setting for the exposure level is center.
20 LANGUAGE 1: AMERICAN ENGLISH
2: ENGLISH
3: FRENCH
4: SPANISH
• This is used to set the language used in the display.
21 RESET FACTORY 1: YES
2: NO
• This is used to return all settings to the factory default settings.
22 SORT AUTO
SELECT
1: ON
2: OFF
• Use this setting to enable or disable sort auto select mode.
24 CHECK RSPF
OPEN
1: ON
2: OFF
• You can set the operation that takes place if the [START] key ( ) is pressed
when the RSPF is not completely closed.
25 VALID COPY
WIDTH
1: 8.5x11
2: 5.5x8.5
• Set the allowed paper sizes for copying from the bypass tray. When "5.5x8.5"
is selected, a copy of a letter size original will only be printed up to invoice
size.
28 LSU SETTING 1: ON
2: OFF
• Select whether copying is only allowed when the polygon motor is rotating, or
also when the polygon motor is stopped.
29 PAPER TYPE 1: PLAIN PAPER
2: HEAVY PAPER
• Set the temperature of the fusing unit when the bypass tray is used. Normally
"PLAIN PAPER" should be selected.
30 DISPLAY
CONTRAST
1: LIGHTER
2: LIGHT
3: NORMAL
4: DARK
5: DARKER
• Set the contrast of the display.
Program
number
Program name
Setting codes
(factory default setting
appears in bold)
Explanation