Specifications

MX-3610N SIMULATION 5 – 47
33
33-2
Purpose
Data clear
Function (Purpose)
Used to delete the ID (IDM) information of
Felica card. (23cpm/31cpm(G) machine
only)
Section
Operation/Procedure
1) Press [EXECUTE] key.
2) Press [YES] key.
The ID (IDM) information of Felica card is deleted.
40
40-2
Purpose
Adjustment/Setup
Function (Purpose)
Manual paper feed tray paper width sensor
adjustment.
Section
Paper feed
Operation/Procedure
1) Open the manual paper feed guide to the max. width (MAX).
2) Press [EXECUTE] key.
The max. width (MAX) detection level is recognized.
3) Open the manual paper feed guide to P1 width (A4).
4) Press [EXECUTE] key.
The P1 width (A4) detection level is recognized.
5) Open the manual paper feed guide to P2 width (A4R).
6) Press [EXECUTE] key.
The P2 width (A4R) detection level is recognized.
7) Open the manual paper feed guide to the min. width (MIN).
8) Press [EXECUTE] key.
The min. width (MIN) detection level is recognized.
When the above operation is not performed normally, "ERROR" is
displayed. When completed normally, "COMPLETE" is displayed.
40-7
Purpose
Adjustment/Setup
Function (Purpose)
Used to set the adjustment value of the
manual paper feed tray paper width sensor.
Section
Paper feed
Operation/Procedure
1) Select a target item to be adjusted with scroll keys.
2) Enter the set value with 10-key.
3) Press [OK] key.
The set value in step 2) is saved.
41
41-1
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the docu-
ment size sensor and the control circuit.
Section
Operation/Procedure
The operating conditions of the sensors and detectors are dis-
played.
The sensors and the detectors which are turned ON are high-
lighted.
41-2
Purpose
Adjustment
Function (Purpose)
Used to adjust the document size sensor
detection level.
Section
Operation/Procedure
1) Open the document cover, and press [EXECUTE] key without
place a document on the document table.
The sensor level without document is recognized.
2) Set A3 (11" x 17") paper on the document table, and press
[EXECUTE] key.
The sensor level when detecting the document is displayed.
When the above operation is normally completed, it is displayed.
41-3
Purpose
Operation test/check
Function (Purpose)
Used to check the operations of the docu-
ment size sensor and the control circuit.
Section
Operation/Procedure
The detection output level (A/D value) of OCSW and the document
sensor (PD1 - PD7) is displayed in real time.
The light receiving range of PD1 - PD7 is 1 - 255. (Default: 128)
MAX POSITION Manual feed max. width
P1(A4)POSITION Manual feed P1 position width (A4)
P2(A4R)POSITION Manual feed P2 position width (A4R)
MIN POSITION Manual feed min. width
Item/Display Content
Default
value
A MAX POSITION Manual feed max. width 241
B P1 (A4) POSITION Manual feed P1 position width (A4) 231
C P2 (A4R) POSITION Manual feed P2 position width
(A4R)
140
D MIN POSITION Manual feed min. width 19
OCSW Document cover status Open: Normal display
Close: Highlighted
PD1 - 7 Document detection
sensor status
No document: Normal display
Document present: Highlighted
Item/Display Content Detection level range
OCSW Original cover SW 0-1 ("1" to Close)
PD1 Document detection 1 0 - 255
PD2 Document detection 2 0 - 255
PD3 Document detection 3 0 - 255
PD4 Document detection 4 0 - 255
PD5 Document detection 5 0 - 255
PD6 Document detection 6 0 - 255
PD7 Document detection 7 0 - 255