Service manual

9
32K-X2000 CK32S60
36K-X2000 CK36S60
SERVICE
No.
CONTROL DESTINATION
ADJUSTMENT ITEM INPUT CONDITIONS
INITIAL
VALUE
S01 PICTURE HEIGHT 00-127 71 RF signal input (TUNER-B) Deflection processor IC (IC502) adjusted
(or EXT. Video input)
S02 V-LINEARITY 00-31 27 " "
S03 V-∫ CORRECTION 00-63 40 40/37 " "
S04 PICTURE WIDTH 00-63 50 " "
S05 E-W PARABOLA 00-63 15 " "
S06 E-W CORNER 00-31 13 " "
S07 TRAPEZIUM 00-127 65 " "
S08 AGC SW 00-01 1 01 " "
S09
PICTURE (SUB CONTRAST) 00-31 28 " "
S10 TINT 00-63 20 " "
S11 COLOR (SUB COLOR) 00-31 13 " "
S12 BRIGHT (BRIGHTNESS) 00-101 58 " "
S13 SHARP (SHARPNESS) 00-27 5 05/00 " "
S14 V-POSITION 00-07 0 00 " "
S15 H-POSITION 00-31 17 " "
S16 R CUT-OFF 00-255 64 " "
S17 G CUT-OFF 00-255 64 " "
S18 B CUT-OFF 00-255 64 " "
S19 G (R) DRIVE 00-127 64 " "
S20 B DRIVE 00-127 64 " "
S21 Y-MUTE/V-OFF 00-02 0 "
00:NORMAL, 01:Y-mute, 03:Hoizontal Y-mute
S22 Y-γ CURVE 00-03 0 03 " VCJ IC (IC401) adjusted
S23 VSM PHASE 00-03 1 02 " "
S24 APACON PEAK f0 00-07 1 01 " "
S25 DC RESTORATION RATE 00-63 21 21 " "
S26 DC RESTORATION LIMIT 00-03 0 00 " "
S27 BLACK STRETCH POINT 00-07 3 03 " "
S28 APL VS BPS 00-03 1 01 " "
S29 B.L.C. 00-01 1 01 " "
S30 DYNAMIC ABL POINT 00-07 4 04 " "
S31 DYNAMIC ABL GAIN 00-07 4 04 " "
S32 ABL POINT 00-07 3 03 " "
S33 ABL GAIN 00-07 3 03 " "
S34 Y-DL 00-01 1 00 " "
S35 TOF-f0 00-07 4 07 " "
S36 TOF-Q 00-07 4 04 " "
S37 VSM GAIN 00-03 1 01 " "
S38 OSD SL 00-01 0 00 " "
S39 C-DECODE 00-255 105 161 " "
S40 OSD POSITION 00-15 11 " C. C. display positioning
M01 INPUT LEVEL (ATT) 00-15 7 " MTS IC (IC3001) adjusted
M02 MTS VCO 00-63 37 " "
M03 FILTER 00-63 30 " "
M04 WIDE BAND 00-63 17 " "
M05 SPECTRAL 00-63 22 " "
M06 MTS DATA READ 00-1 0 Note1 " Factory-adjusted only
Table - A
VARIABLE
DATA
RANGE
FiXED
VALUE
» To call up the service mode, hold down the CH UP and VOL UP keys of the unit at once and plug the AC power
cord into a wall outlet. The unit switches on and comes in the service mode.
» Now hold down both the CH UP and CH DOWN keys of the unit for 2 seconds or longer. the above default values
are written in the EEPROM.
00/00 is depended on picture size.
Left value : 32K-X2000, CK32S60
Right value : 36K-X2000, CK36S60