MODEL HP-TW10 TRUE WIRELESS STEREO EARPHONES HP-TW10 - 100x100 EN.
ENGLISH Introduction Thank you for purchasing this SHARP product. To obtain the best performance from this product, please read this manual carefully. It will guide you in operating your SHARP product. Special Notes The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by SHARP is under license. Other trademarks and trade names are those of their respective owners.
Special Notes (continued) NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Special Notes (continued) IC Radiation Exposure Statement (For Users In Canada) This Class B digital apparatus complies with the Canadian ICES-003 Class B specifications. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. this device may not cause interference, and 2. this device must accept any interference, including interference that may cause undesired operation of the device. ■■ Getting started 1.
Special Notes (continued) Avoiding hearing damage If volume on the earphones is too high, permanent hearing loss may occur. Please set the volume to a safe level. You can become habitual to hear at high volume that may sound normal but can damage your ears. If you experience ringing in your ears or muffled speech, stop listening and have your ears checked by the specialist doctor. The louder the volume, the more quickly the hearing can be damaged.
IMPORTANT SAFETY INSTRUCTIONS Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product.
Contents Page Introduction.................................... 1 Special notes................................. 1 Page Charging operation Charging the earbuds....................... 17 Charging the charging case............. 17 Battery charging............................... 20 Getting started.................................... 3 IMPORTANT SAFETY INSTRUCTIONS............................. 6 Accessories................................... 8 Precautions....................................
Accessories The following accessories are included. Stereo earbuds x 1 pair Charging case x 1 Eartips x 3 pairs USB charging cable x 1 HP-TW10 - 100x100 EN.
Precautions The sound level at a given volume setting depends on speaker efficiency, location and various other factors. It is advisable to avoid exposure to high volume levels, which occurs while turning the unit on with the volume control setting up high, or while continually listening at high volumes. Excessive sound pressure from earbuds can cause hearing loss. Adjust the volume to an appropriate level when using the earbuds.
Precautions (continued) ●● Use this product only with an agency approved power supply which meets local regulatory requirements (e.g., UL, CSA, VDE, CCC). ●● The product rating is located at the bottom of the product. CAUTION: Risk of explosion if the battery is replaced by an incorrect type ●● high or low extreme temperatures that a battery can be subjected to during use, storage or transportation; and ●● low air pressure at high altitude.
Overview Thank you for choosing our product. Our HP-TW10 TRUE WIRELESS STEREO EARPHONES are designed with fashionable looks, powerful features and high compatibility, providing you with hands-free convenience in making calls and listening to music. Best choice for office using, traveling and driving. Bluetooth Wireless Technology With this technology, you can connect the earbuds to its compatible Bluetooth devices without using cables.
Product features and functions • • • • • • • • Integrated Bluetooth earbuds to meet various needs such as music listening and phone answering. With True Wireless Stereo technology, left and right earbuds are wirelessly connected. Stereo sound effect to enjoy perfect music. Small and light, for comfortable and stable wearing. Two usage modes and multiple application scenarios for selection. Built-in 420mAh charging case allows for charging.
General control ■■ Power on ■■ Power off Take out the earbuds from the charging case. They will automatically power on and auto reconnect via Bluetooth to the last device paired. Notes: When the left (L) or right (R) earbuds are taken out for the first time, it will enter pairing mode. Turn on your bluetooth device and search for “HPTW10 SHARP” If the earbuds are not turned on, touch and hold both L and R MFB pad for about 2 seconds. • • HP-TW10 - 100x100 EN.
Bluetooth connection Notes: These earbuds have touch pads (MFB - Multi Function Button). Touch it to operate. R or L earbud can be used independently. • • ■■ Bluetooth pairing Touch and hold the pad for more than 5 seconds to turn it off. The earbuds will automatically power off if there is no connection after 5 minutes. SETTING BLUETOOTH HP-TW10 SHARP Touch and hold the MFB pad for about 2 seconds to power on and it will auto reconnect to the bluetooth enabled device that was last connected.
Music mode Touch and hold R MFB pad for about 2 seconds to skip up to next song. Touch R MFB pad once to increase the volume. Touch and hold L MFB pad for about 2 seconds to skip down to previous song. Touch L MFB pad once to decrease the volume. Touch L or R MFB pad twice to play or pause. HP-TW10 - 100x100 EN.indd 15 Touch L or R MFB pad 3 times to access voice control.
Phone call mode Touch L or R MFB pad twice to answer a call. HP-TW10 - 100x100 EN.indd 16 Touch L or R MFB pad twice to end a call. Touch and hold L or R MFB pad for about 2 seconds to reject an incoming call. While answering a call, to switch the call from the earbuds to mobile phone or vice versa, touch and hold L or R MFB pad for about 2 seconds.
Charging operation ■■ Charging the earbuds 1. Put the earbuds into the charging case. 2. Earbuds red LED lights up indicate under charging. 3. Earbuds red LED turns off indicate fully charged. Charging: Red LED light up Fully charged: Red LED light off ■■ Charging the charging case Before using any adapter to charge the charging case, check whether the specifications of the adapter meets the requirements. The recommended output voltage of the adapter is DC5V+/-0.
Charging operation (continued) Charging via USB cable : Insert the USB cable (provided) to the USB terminal located at the rear of the charging case as shown. Wireless charging : Place the charging case on the surface of a wireless charger with direction as shown. (Front side up) Precautions for wireless charging : Do not place any conductive materials such as metal objects or magnets between the charging case and the wireless charger.
Charging operation (continued) 1. 0-25% 1st white LED blinking. 2. 25-50% 1st LED lights up, 2nd LED blinking. 3. 50-75% 1st and 2nd LED light up, 3rd LED blinking. 4. 75-99% 1st, 2nd and 3rd LED light up, 4th LED blinking. 5. 100% fully charged, four LEDs light up permanently. Notes : To extend the service life of the battery, you are advised to charge the charging case at least once a month. Please use the charging case provided to charge the earbuds. • • HP-TW10 - 100x100 EN.
Charging operation (continued) ■■ Battery charging The earbuds use embedded rechargeable battery that cannot be removed. Do not attempt to remove the battery from the earbud or the charging case. Otherwise, the earbud or charging case may be damaged. If the earbud is not used in a long time, keep it in a cool and well ventilated place. Charge the earbuds every months. 1. When red LED on the earbud blinks with a voice message “Battery low”, put the earbuds back into the charging case.
Troubleshooting Problem Description Cause Solution The earbuds The earbud is out of power. cannot be powered on The MFB button is not pressed and held for sufficient time. The earbuds The earbuds metal contacts cannot be are not well connected to the charged charging case pins. HP-TW10 - 100x100 EN.indd 21 Put the earbuds into the charging case. If the charging case is also out of power, charge the case with an adapter first. Press and hold the MFB button again.
Troubleshooting (continued) Problem Description Cause Solution The earbuds The earbud program is in error cannot be due to an incorrect operation. powered off. Reset the earbuds. Refer to “Factory reset” on this page. The earbuds The earbuds did not enter the cannot be pairing state. searched or pairing fails. Enable the earbuds to enter the pairing mode. During power off, touch and hold L or R MFB pads for about 4 seconds. It will enter pairing mode.
Specification As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual unit. ■■ General Rated input voltage DC 5 V, 210 mA (USB type C) Output power RMS: Total 6 mW (3 mW + 3 mW) Frequency response 20 Hz - 20 kHz Music playback time (*1) Approx.
Specification (continued) ■■ Bluetooth Version V 5.0 (HSP / HFP / A2DP / AVRCP) Maximum power transmitted < 20 dbm Frequency bands 2.402 GHz 2.480 GHz HP-TW10 - 100x100 EN.
HP-TW10 - 100x100 EN.
HP-TW10 - 100x100 EN.
92L5350010443A HP-TW10 - 100x100 EN.
