CB OPERATOR’S MANUAL 98012620-1 LIS T E D ® MODEL # CB-301007D ORDER # 1.106-551.0 CB-402007A MODEL # CB-353007A ORDER # 1.106-556.0 1.106-552.0 CB-353007B 1.106-557.0 CB-402007B 1.106-553.0 CB-353007C 1.106-558.0 CB-402007C 1.106-554.0 CB-353007G 1.106-559.0 CB-402007H 1.106-555.0 CB-353007H 1.106-560.0 To locate your local Shark Commercial Pressure Washer Dealer nearest you, visit www.Sharkpw.com 9.801-262.
CONTENTS Important Safety Information 4-5 Component Identification 6 Assembly Instructions 7 Operating Instructions 8 Applying Detergent & General Operating Techniques 9 Shut Down & Clean-Up 10 Storage 10 Troubleshooting 11 Preventative Maintenance 12 Oil Change Record 12 Hose & Spray Gun Assembly & Parts List 13 Exploded View 14-15 Exploded View Parts List 16-17 VB8 Valve Exploded View and Parts List 18 Pump Exploded View and Parts List 19 Specifications Page 20-21 Multi-Roo
PRESSURE WASHER OPERATOR’S MANUAL INTRODUCTION & IMPORTANT SAFETY INFORMATION Thank you for purchasing a Shark Pressure Washer. We reserve the right to make changes at any time without incurring any obligation. Owner/User Responsibility: The owner and/or user must have an understanding of the manufacturer’s operating instructions and warnings before using this pressure washer. Warning information should be emphasized and understood.
PRESSURE WASHER WARNING: Grip cleaning wand securely with both hands before starting. Failure to do this could result in injury from a whipping wand. WARNING RISK OF INJURY FROM FALLS WHEN USING LADDER. TRIGGER GUN KICKS BACK - HOLD WITH BOTH HANDS WARNING: High pressure developed by these machines will cause personal injury or equipment damage. Keep clear of nozzle. Use caution when operating.
OPERATOR’S MANUAL PRESSURE WASHER COMPONENT IDENTIFICATION High Pressure Nozzle Soap Nozzle Water Supply Wand On/Off Switch Quick Coupler Garden Hose Inlet Spray Gun Discharge Nipple Garden Hose (not included) Hose Coupler Trigger Swivel Connector Detergent Injector Detergent Pick-up Tube High Pressure Hose 98012620-2 Detergent Injector - Allows you to siphon and mix detergents, when used with soap nozzle.
PRESSURE WASHER Nozzle Safety Latch Coupler High Pressure Hose 98012620-4 98012620-3 STEP 1: Attach the high pressure hose to the spray gun using teflon tape on hose threads. Use safety latch to prevent from opening. STEP 2: Connect garden hose to the cold water source. Before installing nozzle, turn on water supply and run machine, allowing water to flush through the system until clear. 98012620-5 STEP 3: Insert nozzle into coupler.
OPERATOR’S MANUAL PRESSURE WASHER OPERATING INSTRUCTIONS Cold Water Source Garden Hose 98012620-7 98012620-8 STEP 1: Connect garden hose to the cold water source and turn water on completely. Never use hot water. 98012620-9 STEP 2: Trigger the spray gun to eliminate trapped air then wait for a steady flow of water to emerge from the spray wand. Then install nozzle. On/Off Switch Safety Latch 98012620-11 98012620-10 STEP 4: Turn machine on by pushing switch at front of machine.
STEP 1: Use detergent designed specifically for pressure washers. Household detergents could damage the pump. Prepare detergent solution as required by the manufacturer. Fill a container with pressure washer detergent. Place the filter end of detergent suction tube into the detergent container. OPERATOR’S MANUAL 98012620-13 WARNING: Some detergents may be harmful if inhaled or ingested, causing severe nausea, fainting or poisoning. The harmful elements may cause property damage or severe injury.
PRESSURE WASHER OPERATOR’S MANUAL SHUTTING DOWN AND CLEAN-UP 98012620-16 98012620-17 STEP 1: Remove detergent suction tube from soap container and insert into one gallon of fresh water. Use black soap nozzle with detergent injector. Pull trigger on spray gun and siphon water for one minute. STEP 2: Turn off machine by pushing switch on front panel. Pump Water Inlet 98012620-18 STEP 3: Turn off water supply.
PROBLEM POSSIBLE CAUSE SOLUTION PUMP RUNNING NORMALLY BUT PRESSURE LOW ON INSTALLATION Pump sucking air Check water supply and possibility of air. Check valves sticking Check and clean or replace if necessary. Unloader valve seat faulty Check and replace if necessary. Nozzle incorrectly sized Check and replace if necessary. Worn piston packing Check and replace if necessary. Valves worn Check and replace if necessary. Blockage in valve Check and clean if necessary.
PRESSURE WASHER OPERATOR’S MANUAL PREVENTATIVE MAINTENANCE PREVENTATIVE MAINTENANCE This pressure washer was produced with the best available materials and quality craftsmanship. However, you as the owner, have certain responsibilities for the correct care of the equipment. Attention to regular preventative maintenance procedure will assist in preserving the performance of your equipment. Contact your dealer for maintenance.
PRESSURE WASHER HOSE & SPRAY GUN ASSEMBLY 8 4 PRESSURE WASHER 6 OPERATOR’S MANUAL 3 5 7 10 1 9 OPERATOR’S MANUAL 11 2 98012620-23 HOSE & SPRAY GUN ASSEMBLY PARTS LIST ITEM PART NO. DESCRIPTION 1 QTY 9.802-166.0 Coupler, 3/8" Female 1 9.802-100.0 Quick Coupler O-Ring 1 2 8.739-125.0 Hose, 3/8" x 50', 1 Wire,Tuff-Flex 1 3 8.701-384.0 Gun, ST-1500, 5000 10.4 GPM 1 4 9.802-219.0 Wand w/Side Grip 1 5 8.712-398.
PRESSURE WASHER EXPLODED VIEW 10 Enlarged Reverse View 64 63 7 71 63 20 38 13 62 78 76 9 OPERATOR’S MANUAL 74 58 Time Delay Option 75 Auto Start Option 61 64 22 12 4 5 25 80 23 58 62 13 70 64 62 9 3 71 61 66 51 19 58 1 64 2 76 75 82 54 6 77 7 21 64 63 Auto Start Option 11 77 74 22 12 For Detail See Pump Assy. 25 24 98012620-24 15 8 14 23 14 9.801-262.0 • Shark CB • Rev.
PRESSURE WASHER EXPLODED VIEW OPERATOR’S MANUAL PRESSURE WASHER 27 79 OPERATOR’S MANUAL 43 46 68 44 17 50 40 41 16 42 73 26 28 45 50 49 39 69 29 53 46 32 37 72 57 56 31 59 65 33 30 67 60 47 55 59 78 35 36 98012020-25 34 52 80 18 81 19 48 50 15 9.801-262.0 • Shark CB • Rev.
PRESSURE WASHER OPERATOR’S MANUAL EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 1 Unloader, See Specifications Pages 23 8.932-969.0 Label, Warn Service Cord 1 2 Pump, See Specifications Pages 24 9.802-039.0 Elbow, 1/2" JIC x 3/8", 90° 1 3 Motor, See Specifications Pages 4 9.802-551.0 9.804-556.0 Transformer (552.0, 553.0 554.0, 556.0, 557.0, 558.0) Transformer (555.0, 559.0, 560.0) 1 1 5 8.933-007.0 Fuse, ATMR, 1 Amp, 600V (552.
PRESSURE WASHER QTY 39 9.800-064.0 Label 1 40 Bushing, See Specifications Pages 41 Bushing, See Specifications Pages 42 Pump Pulley, See Specifications Pages 43 Motor Pulley, See Specifications Pages 44 Belt, See Specifications Pages 45 9.802-522.0 Strain Relief, 1" 1 46 9.802-765.0 Screw, 1/4" x 1/2", BH SOC CS 47 12 9.802-817.0 Washer, 3/8" x 1" Steel 48 9.802-710.0 Bolt, 5/16" x 1 NC (551.0) 9.802-720.0 Bolt, 3/8" x 1" NC, HH (552.0-560.0) 49 9.800-034.
9.802-362.0 2 30 27 28 29 16 25 37 15 32 11 31 27 26 OPERATOR’S MANUAL PRESSURE WASHER VB8 UNLOADER VALVE EXPLODED VIEW 12 10 24 9 23 39 13 6 22 14 8 13 21 5 7 20 38 40 36 18 4 35 19 17 34 33 3 2 1 VB8 UNLOADER VALVE EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION 1 60.0058.31 3/8 Bsp F Outlet Fitting 1 22 60.1210.31 Upper Frame QTY 1 2 10.3070.02* O-ring 1.78 x 18.77 mm 2 23 14.7421.00 1/4" Ball 1 3 60.0053.
PRESSURE WASHER OPERATOR’S MANUAL 2 1 3 14 10 4 2 9 PRESSURE WASHER Specifications PUMP EXPLODED VIEW Time Delay Shutdown Option 4 6 16 12 5 13 8 Auto Start/Stop Option 15 11 3 17 98012620-27 PUMP EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY 1 8.750-299.0 Unloader, VRT3, 8 GPM @ 4500 PSI 2 9.802-039.0 Elbow, 1/2" JIC, 3/8", 90° 3 9.802-048.0 Swivel, 1/2" JIC x 3/8" Male 1 1 16 9.802-362.
PRESSURE WASHER Specifications SPECIFICATIONS Pump Pump Part No. Pump Pulley Pump Pulley Part No. Pump Bushing Bushing Part No. 1.106-551.0 KD3030R 1.106-552.0 KM4035R 9.804-006.0 AK74H 9.802-369.0 24MM 8.751-189.0 2AK74H 9.802-369.0 24MM 1.106-553.0 1.106-554.0 KM4035R 8.751-189.0 2AK74H 9.802-369.0 KM4035R 8.751-189.0 2AK74H 9.802-369.0 1.106-555.0 KM4035R 8.751-189.0 2AK74H 1.106-556.0 KM4035R 8.751-189.0 2BK80H 1.106-557.0 KM4035R 8.751-189.0 1.106-558.
Motor Pulley Motor Pulley Part No. 551.0 9.802-339.0 AK32x5/8 9.804-004.0 552.0 9.802-336.0 2AK56H 9.802.373.0 553.0 8.751-004.0 2AK56H 9.802-373.0 554.0 8.751-004.0 2AK56H 9.802-373.0 555.0 9.802-330.0 2AK56H 9.802-373.0 556.0 8.715-097.0 2BK52H 9.802-386.0 557.0 8.751-014.0 2BK50H 558.0 8.751-014.0 2BK50H 559.0 9.802-332.0 560.0 9.802-333.0 Motor Bushing Motor Part No. Belt Size Belt Part No. Contractor Part No. Overload Part No. N/A N/A AX40 (1) HX1-1/8" 9.
PRESSURE WASHER OPERATOR’S MANUAL MULTI-ROOM INSTALLATION 98012020-26 22 9.801-262.0 • Shark CB • Rev.
PRESSURE WASHER KD.1 PUMP EXPLODED VIEW OPERATOR’S MANUAL TORQUE SPECS Item # Ft.-lbs 14 65 17 18 25 7.6 34 7 44 13 OPERATOR’S MANUAL PRESSURE WASHER 9.803-417.0 KD 3025.1 9.804-006.0 KD 3030.1 9.804-019.0 KD 4020.1 KD.1 PUMP EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 1 9.803-938.0 Crankcase 1 11* See Kits O-Ring Ø1.78 x 15.54 6 2* See Kits Plunger Oil Seal 3 12* See Kits Valve Assembly 6 3* See Kits O-Ring Ø1.78 x 28.
PRESSURE WASHER OPERATOR’S MANUAL KD.1 PUMP EXPLODED VIEW PARTS LIST (CONT) ITEM PART NO. DESCRIPTION QTY 33 8.933-010.0 Crankshaft Seal 1 34* See Kits Plunger Nut 3 35* See Kits Copper Spacer 3 36* See Kits Plunger, 15mm (3030) 3 See Kits Plunger, 18mm (4020, 3025) 3 37* See Kits Copper Spacer 3 38* See Kits O-Ring Ø1.78 x 5.28 3 39* See Kits Teflon Ring 3 40* See Kits Plunger Rod 3 41 9.803-965.0 Connecting Rod Pin 3 42 9.803-966.0 Connecting Rod 3 43 9.
KM3540R.3 KM4030R.3 KM4030L.3 KM4035R.3 KM4035L.3 KM5030R.3 KM5030L.3 TORQUE SPECS Ft.-lbs 14 75 15 30 23 8 33 9 43 13 48 7.6 OPERATOR’S MANUAL Item # OPERATOR’S MANUAL PRESSURE WASHER 8.751-186.0 8.751-187.0 8.751-188.0 8.751-189.0 8.751-190.0 8.751-191.0 8.751-192.0 PRESSURE WASHER KM.3 SERIES PUMP EXPLODED VIEW KM.3 SERIES PUMP EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY ITEM PART NO. DESCRIPTION QTY 1 8.751-216.0 Crankcase 1 23 9.802-944.
PRESSURE WASHER OPERATOR’S MANUAL KM.3 SERIES PUMP EXPLODED VIEW PARTS LIST ITEM PART NO. DESCRIPTION QTY 36* See Kits Below Copper Spacer 3 37* See Kits Below O-Ring Ø1.78 x 7.66 3 38* See Kits Below Teflon Ring 3 39 8.751-224.0 Plunger Rod 3 40 9.803-158.0 Connecting Rod 3 41 8.751-228.0 Connecting Rod Pin 3 42 9.803-218.0 Spring Washer 6 43 9.803-238.0 Connecting Rod Screw 6 44 8.933-016.0 O-Ring, Ø2.62 x 126.67 1 45 8.751-229.0 Crankcase Cover 1 46 9.803-197.
8.750-297.0, 8 GPM, 2320 PSI 8.750-298.0, 8 GPM, 3630 PSI 8.750-299.0, 8 GPM, 4500 PSI ITEM PART NO. 14 19 1 1 25 18 8.750-712.0 8.750-713.0 Outlet Fitting Knob, Unloader 8.750-709.0 Repair Kit, VRT3, 2320/3630 PSI 8.750-710.
www.sharkpw.com Shark CB 9.801-262.0 • Revised 01/12 • Printed in U.S.A.
