User's Manual

POS Machine User Manual
Please read this user manual carefully before using the POS and keep
it in a safe place for future reference.
Basic Parameters of POS machine
Operating system
Processor
Display
Memory
Touchscreen
WIFI
Bluetooth
Printer
Speaker
External ports
External memory card
Overall dimensions (H×W×D) CM
Power adapter
Android 6.0
Qualcomm 8-core Snapdragon 615
14-inch IPS FHD1920×1080 resolution
16GB ROM+ 2GB RAM
Multi-touch capacitive screen
Dual-band WiFi, 802.11a/b/g/n(2.4GHz/5GHz) supported
Wireless
GSM900/1800/850/1900, WCDMA850/1900/2100
Bluetooth 3.0/4.0 and iBeacon supported
80mm printer head, paper roll diameter of 80mm, with an auto-cutter
1.2W each, maximal 90dB
5x USB type-A ports, 1x RJ11 serial port, 1x RJ12 24v cashbox port,
1x RJ45 LAN port, 1x headset jack, 1x power port, 1x Micro-USB
debugging port
MicroSD (TF) supported, maximum 64G memory
37.4X33.8X22.4 CM
Model No.:EA10681P-240 Input: AC 100~240V/2.0A Output: DC 24V/2.5A
Manufacture: EDAC Power Electronics Co., Ltd.
Precautions
· Please insert the AC plug into the AC outlet according to
the identifying input on the power adapter;
· It is prohibited to use the device in any places with
potential explosive gases;
· Nonprofessionals shall not open the power adapter
anyhow so as to avoid dangers;
· The device is a Grade A product. In living environment,
the product may cause radio interference. Therefore,
users may be required to take practical measures against
the interference.
· Adapter shall be installed near the equipment and shall
be easily accessible. The plug considered as disconnect
device of adapter.
· Avoid installing or using during thunder and lightning,
otherwise lightning stroke may occur;
· Cut off the power immediately if there is abnormal
smell, overheating or smog;
· Do not touch the sharp paper cutting tool!
Statement
The company is not responsible for the following
behaviors:
· Damages caused by using and maintaining the
device without following the User Guide;
· Damages or problems caused by selection of
objects or Consumables (products which are not
the initial ones provided or recognized by the
company).
In this case, the company will not undertake any
responsibility. No one is entitled to modify or
change the product unless permitted by the
company.
Disclaimer
Discrepancies between the product and the file
concerning details may raise due to product
updates. Please be subject to the material object.
The company reserves the right to interpret the
file and the right to revise this manual without
prior notices.
Please make sure the temperature for adapter will
be from -10 ℃ to 40 ℃.
Please make sure the temperature for device will be
from -10 ℃ to 40 ℃.
· Do not use the device near water or in humid environment.
Keep liquid from falling onto the terminal;
·
Do not use the device in extremely cold and hot
environment, e.g. around fire or lighted cigarettes;
·
Do not smash, throw or bend the device;
·Use the device in clean and dustfree environment as much
as possible and keep small items from falling into the
terminal;
· Do not use it near medical devices unless permitted.
Recommendation
Safety Warning
Important Safety Instructions
1 EU Regulatory Conformance
Hereby, Shanghai Sunmi Technology Co., Ltd. declares that this Radio LAN device is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC. For the declaration of conformity,
Notice: Observe the national local regulations in the location where the device is to beused. This device
may be restricted for use in some or all member states of the European Union (EU).
The device complies with RF specifications when the device used at least 20cm from human body.
The users has to turn off the 5GHz WiFi in outdoor environment.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiated radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
0700
Symptom
Printer Out of Service
Device Crash
Common Troubleshooting
· Make sure the paper case is closed proerly；
· Make sure the printing is proeperly and
installed；
Check whether the paper case is installed
with 80mm thermal parinting paper roll；
· Check whether the paper is placed reversely
when printing blank con-tent;
Press the power button for 11 seconds
to restart
Confirmation
·
RF Exposure Warning Statements:
The antenna(s) used for this transmitter must be installed
to provide a separation distance of at least 20 cm from all
persons during the normal operations.