SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision Compliance Information: FCC Compliance Statement: This device complies with Part 15 of the FCC Rules . Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. This device must accept any interference received, including interference that may cause undesired operation.
Smart Machine Smart Decision Document Title SIM7600A-H_User Manual Version V1.00 Date 2017-11-24 Status Released Document Control ID SIM7600A-H_User Manual_V1.00 General Notes SIMCom offers this information as a service to its customers to support the application and engineering efforts that use the products designed by SIMCom. The information provided is based on the requirements specifically from the customers.
Smart Machine Smart Decision Contents Contents .............................................................................................................................................4 Table Index ........................................................................................................................................6 Figure Index ......................................................................................................................................7 Revision History .....
Smart Machine Smart Decision 3.11 Other interface .................................................................................................................35 3.11.1 Sink Current Source ..................................................................................................35 3.11.2 ADC ..........................................................................................................................36 4 RF Specifications ............................................................
Smart Machine Smart Decision Table Index Table 1: SIM7600A-H frequency bands .............................................................................................................. 9 Table 2: General features ................................................................................................................................... 10 Table 3: Pin Definitions .....................................................................................................................................
Smart Machine Smart Decision Figure Index Figure 1: SIM7600A-H Block Diagram............................................................................................................. 10 Figure 2: Pin assignment overview .................................................................................................................... 12 Figure 3: Dimensions (Unit: mm) ......................................................................................................................
Smart Machine Smart Decision Revision History Data Version Description of change Author 2017-11-24 V1.00 new Shengwu.sun SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision 1 Introduction This document describes the electronic specifications, RF specifications, interfaces, mechanical characteristics and testing results of the SIMCom SIM7600A-H. With the help of this document and other software application notes/user guides, users can understand and use modules to design and develop applications quickly. 1.1 Product Outline The SIM7600A-H support many air-interface standards, refer to the following table.
Smart Machine Smart Decision GNSS Antenna Main Antenna DDR AUX Antenna NAND Flash GNSS RF GSM/WCDMA /LTE RF FEM WCDMA /LTE RF FEM SMT Interface Qualcomm Chip Baseband RF Transceiver GSM/ WCDMA/LTE PA USIM UART I2C PCM USB GPIOs Interrupt ADC Status LED LDO Sink Current Source SYSTEM POWER XO 19.2MHz Power Management VBAT Power On Reset VBAT Figure 1: SIM7600A-H Block Diagram 1.4 Functional Overview Table 2: General features Feature Implementation Power supply Single supply voltage 3.4～4.
Smart Machine Smart Decision Audio feature Support PCM interface Only support PCM master mode and short frame sync, 16-bit linear data formats UART interface A full modem serial port by default Baud rate: 300bps to 4Mbps(default:115200bps) Auto-bauding baud rate: 9600,19200,38400,57600,115200bps Can be used as the AT commands or data stream channel. Support RTS/CTS hardware handshake Multiplex ability according to GSM 07.10 Multiplexer Protocol. USB USB 2.
Smart Machine Smart Decision 2 Package Information 2.1 Pin Assignment Overview All functions of the SIM7600A-H will be provided through 87 pads that will be connected to the customers’ platform. The following Figure is a high-level view of the pin assignment of the SIM7600A-H. SIM7600A (Top View) Figure 2: Pin assignment overview SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision Table 3: Pin Definitions Pin No. Pin name Pin No.
Smart Machine Smart Decision 69 RI 70 DCD 71 TXD 72 DTR 73 PCM_OUT 74 PCM_IN 75 PCM_SYNC 76 PCM_CLK 77 GND 78 GND 79 GNSS_ANT 80 GND 81 GND 82 MAIN_ANT 83 COEX1* 84 COEX2 85 BOOT_CFG0* 86 COEX3* 87 GPIO77 *Note: Before the normal power up, pin48 cannot be pulled up. 2.
Smart Machine Smart Decision VDD_1V8 15 GND 1,2,5, 10,14,37 ,40,41,4 3,57,58, 60,61,64 ,65,77,7 8,80,81 PO （The voltage can be configured to 2.8V by AT command）. 1.8V SMPS output with Max 50mA current output for external circuit, such as level shift circuit. If unused, keep it open. Ground System Control DI,PU System power on/off control input, active low. The high voltage is 0.8V; 4 DI, PU System reset control input, active low. RESET has been pulled up to 1.
Smart Machine Smart Decision SPI_MOSI 8 DO SPI master out/slave in data SPI_CS 9 DO SPI chip-select output USB_VBUS 11 DI,PD Valid USB detection input with 3.0~5.25V detection voltage USB_DN 12 I/O Negative line of the differential, bi-directional USB signal. USB_DP 13 I/O USB_ID 16 DI Positive line of the differential, bi-directional USB signal.
Smart Machine Smart Decision FLIGHTMODE 54 DI,PU STATUS 49 DO GPIO41 52 IO Flight Mode control input. High level(or open): Normal Mode Low level: Flight Mode Operating status output. High level: Power on and firmware ready Low level: Power off GPIO GPIO43 50 IO GPIO GPIO3 33 IO GPIO GPIO6 34 IO GPIO DO NOT PULL UP GPIO43 DURING NORMAL POWER UP! Default: GPIO Optional: SD card detecting input.
Smart Machine Smart Decision 2.3 Mechanical Information The following figure shows the package outline drawing of Module. Figure 3: Dimensions (Unit: mm) SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision 2.4 Footprint Recommendation Figure 4: Footprint recommendation (Unit: mm) SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision 3 Interface Application 3.1 Power Supply On VBAT pads, a ripple current up to 2A typically, may cause voltage drop. Therefore, the power supply for these pads must be able to provide sufficient current up to more than 2A in order to avoid the voltage drop of more than 300mV. Table 6: VBAT Pins electronic characteristic Symbol Description VBAT Module power voltage 3.4 3.8 IVBAT(peak) Module power peak current in normal mode. 1.
Smart Machine Smart Decision In addition, in order to guard over voltage protection, it is suggested to use a zener diode with 5.1V reverse zener voltage and more than 500mW power dissipation. Table 7: Recommended zener diode list No. Manufacturer Part Number power dissipation Package 1 On semi MMSZ5231BT1G 500mW SOD123 2 Prisemi PZ3D4V2H 500mW SOD323 3 Vishay MMSZ4689-V 500mW SOD123 4 Crownpo CDZ55C5V1SM 500mW 0805 3.1.
Smart Machine Smart Decision 3.1.3 Voltage Monitor To monitor the VBAT voltage, the AT command “AT+CBC” can be used. For monitoring the VBAT voltage outside or within a special range, the AT command “AT+CVALARM” can be used to enable the under-voltage warning function. If users need to power off Module, when the VBAT voltage is out of a range, the AT command “AT+CPMVT” can be used to enable under-voltage power-off function.
Smart Machine Smart Decision VBAT Ton PWRKEY (Input) Ton(status) STATUS (Output) Ton(uart) Active Undefined UART Port USB Port Ton(usb) Active Undefined Figure 9: Power on timing sequence Table 8: Power on timing and electronic characteristic Symbol Parameter Ton The time of active low level impulse of PWRKEY pin to power on module Ton(status) The time from power-on issue to STATUS pin output high level(indicating power up ready ) Ton(uart) The time from power-on issue to UART port ready
Smart Machine Smart Decision For details about “AT+CPOF” and “AT+CPMVT”, please refer to Document [1]. These procedures will make modules disconnect from the network and allow the software to enter a safe state and save data before modules are powered off completely. The power off scenario by pulling down the PWRKEY pin is illustrated in the following figure.
Smart Machine Smart Decision The RESET pin has been pulled up to 1.8V internally, so it does not need to be pulled up externally. It is strongly recommended to put a100nF capacitor and an ESD protection diode close to the RESET pin. Please refer to the following figure for the recommended reference circuit. Figure 11: Reference reset circuit Table 10: RESET pin electronic characteristic Symbol Description Min.
Smart Machine Smart Decision Figure 12: UART full modem Figure 13: UART null Modem The Module UART is 1.8V voltage interface. If user’s UART application circuit is a 3.3V voltage interface, the level shifter circuits should be used for voltage matching. The TXB0108RGYR provided by Texas Instruments is recommended. The following figure shows the voltage matching reference design.
Smart Machine Smart Decision 3.3.2 RI and DTR Behavior The RI pin can be used to interrupt output signal to inform the host controller such as application CPU. Normally RI will stay at high level until certain conditions such as receiving SMS, or a URC report come in. It will then change to low level. It will stay low until the host controller clears the interrupted event with “AT+CRIRS” AT command.
Smart Machine Smart Decision 3.4.1 USB Application Guide Module can be used as a USB device. Module supports the USB suspend and resume mechanism which can reduce power consumption. If there is no data transmission on the USB bus, Module will enter suspend mode automatically and will be resumed by some events such as voice call, receiving SMS, etc.
Smart Machine Smart Decision Table 12: USIM Electronic characteristic 3.0V mode (USIM_VDD=2.95V) Symbol Parameter Min. Typ. Max. Unit USIM_ VDD LDO power output voltage 2.75 2.95 3.05 V VIH High-level input voltage 0.65*USIM_VDD - USIM_VDD +0.3 V VIL Low-level input voltage -0.3 0 0.25*USIM_VDD V VOH High-level output voltage USIM_VDD -0.45 - USIM_VDD V VOL Low-level output voltage 0 0 0.45 V 3.5.
Smart Machine Smart Decision 3.5.
Smart Machine Smart Decision 3.6 PCM Interface Module provides a PCM interface for external codec, which can be used inmaster mode with short sync and 16 bits linear format. Table 14: PCM Format Characteristics Specification LineInterfaceFormat Linear(Fixed) Datalength 16bits(Fixed) PCM Clock/Sync Source Master Mode(Fixed) PCMClockRate 2048 KHz (Fixed) PCMSyncFormat Shortsync(Fixed) Data Ordering MSB Note: For more details about PCM AT commands, please refer to document [1]. 3.6.
Smart Machine Smart Decision Figure 22: Module to EXT codec timing Table 15: PCM Timing Parameters Parameter Description Min. Typ. Max. Unit T(sync) PCM_SYNC cycle time – 125 – μs T(synch) PCM_SYNC high level time – 488 – ns T(syncl) PCM_SYNC low level time – 124.
Smart Machine Smart Decision Figure 23: Audio codec reference circuit Note: Module can transmit PCM data by theUSB portbesidesthe PCM interface. For more details please refer to documents [1] and [23]. 3.7 I2C Interface Module provides a I2C interface compatible with I2C specification, version 2.1, with clock rate up to 400 kbps. Its operation voltage is 1.8V. 3.7.1 I2C Design Guide The following figure shows the I2C bus reference design.
Smart Machine Smart Decision 3.8 Network Status The NETLIGHT pin is used to control Network Status LED, its reference circuit is shown in the following figure. Figure 25: NETLIGHT reference circuit Note: The value of the resistor named “R” depends on the LED characteristic.
Smart Machine Smart Decision Table 18: Pin multiplex function list Pin Number Pin Name Default Function Alternate Function 4 SCL SCL GPIO11 5 SDA SDA GPIO10 12 USIM_DET GPIO34 18 PCM_CLK PCM_CLK 19 PCM_SYNC PCM_SYNC USIM_DET GPIO23,SPI_CLK I2C_SCL GPIO20,SPI_MOSI 20 PCM_IN PCM_IN, 21 PCM_OUT PCM_OUT GPIO21,SPI_MISO GPIO22,SPI_CS_N I2C_SDA Note ： For more details of AT commands about GPIO multiplex function,please refer to document [1]. 3.11 Other interface 3.11.
Smart Machine Smart Decision Note: The sinking current can be adjusted to meet the design requirement through the AT command “AT+ CLEDITST =<0>, ”.The “value” ranges from 0 to 8, on behalf of the current from 0mA to 40mA by 5mA step. 3.11.2 ADC Module has 1 dedicated ADC pins named ADC. They are available fordigitizing analog signals such as battery voltage and so on. These electronic specifications are shown in the following table. Table 20: ADC Electronic Characteristics Min.
Smart Machine Smart Decision 4 RF Specifications 4.1 WCDMA/LTE RF Specifications Table 21: Conducted transmission power Frequency WCDMA B2 WCDMA B5 LTE-FDD B2 LTE-FDD B4 LTE-FDD B12 Power 24dBm +1/-3dB 24dBm +1/-3dB 23dBm +/-2.7dB 23dBm +/-2.7dB 23dBm +/-2.7dB Min.
Smart Machine Smart Decision 4.2 WCDMA/LTE Antenna Design Guide Users should connect antennas to Module’s antenna pads through the micro-strip line or other types of RF trace. The trace impedance must be controlled in 50Ω. SIMCom recommends that the total insertion loss between Module and antenna should meet the following requirements: Table 25: Trace Loss Frequency Loss 700MHz-960MHz <0.5dB 1710MHz-2170MHz <0.9dB 2300MHz-2650MHz <1.
Smart Machine Smart Decision Figure 28: Antenna matching circuit (DIV_ANT) In above figure, R3, C3, C4 and R4 are used for auxiliary antenna matching. By default, the R3, R4 are 0Ωresistors, and the C3, C4 are reserved for tuning. D2 is a TVS for ESD protection, and it is optional for users according to application environment. Two TVS are recommended in the table below.
Smart Machine Smart Decision SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision Figure 29: Antenna matching circuit (MAIN_ANT) In figure 29, the components L106, C118, C119 and R111 or R102 are used for antenna matching, the values of components can only be achieved after the antenna tuning and usually provided by antenna vendor. By default, the L106,R111or R102 are 0Ω resistors, and the C118, C119 are reserved for tuning are reserved for tuning.
Smart Machine Smart Decision GNSS data format: NMEA-0183 GNSS Current consumption : 100mA ((WCDMA/LTE Sleep ,in total on VBAT pins) GNSS antenna: Passive/Active antenna Note: If the antenna is active type, the power should be given by main board, because there is no power supply on GPS antenna pad. If the antenna is passive, it is suggested that the external LNA should be used. 4.3.2 GNSS Application Guide Users can adopt an active antenna or a passive antenna as GNSS signal transceiver.
Smart Machine Smart Decision LNA should apply the following requirements as table 28. LNA is also suggested to put near the passive antenna. Table 27: LNA requirements Parameter Min Max Unit Vdd Idd LNA_EN Gain VSWR 1.5 3.3 3 V mA V dB 1.3 14 17 2 GNSS can be used by NMEA port. User can select NMEA as output through UART or USB. NMEA sentences are automatic and no command is provided. NMEA sentences include GSV, GGA, RMC, GSA, and VTG.
Smart Machine Smart Decision 5 Electrical Specifications 5.1 Absolute Maximum Ratings Absolute maximumrating for digital and analog pins of Module are listed in the following table: Table 28: Absolute maximum ratings Parameter Voltage at VBAT Voltage at VBUS Voltage at digital pins (RESET,SPI,GPIO,I2C,UART,PCM) Voltage at digital pins :USIM Voltage at PWRKEY 5.2 Min. -0.5 -0.5 -0.3 -0.3 -0.3 Max. 6.0 6.3 2.1 3.05 1.8 Unit V V V V Typ. 3.8 5 Max. 4.2 5.
Smart Machine Smart Decision The operating temperature of Module is listed in the following table. Table 31: Operating temperature Parameter Normal operation temperature Min. -30 Typ. 25 Max. 80 Unit ℃ Extended operation temperature* -40 25 85 ℃ Storage temperature -45 25 +90 ℃ *Note: Module is able to make and receive voice calls, data calls, SMS and make WCDMA/HSPA+/LTE traffic in -40℃ ~ +85℃.
Smart Machine Smart Decision power supply. In this mode, the RF part of the module will not work but the serial port and USB port are still accessible. The power consumption in this mode is lower than normal mode. Power off 5.3.2 Module will go into power off mode by sending the AT command “AT+CPOF” or by pulling down the PWRKEY pin normally. In this mode the power management unit shuts down the power supply and software is not active. The serial port and USB are is not accessible.
Smart Machine Smart Decision Table 33: Current consumption on VBAT Pins (VBAT=3.8V) UMTS Sleep/Idle Mode WCDMA supply current (without USB connection) Sleep mode @DRX=9Typical: 1.11 Idle mode @DRX=9Typical: 17.5 LTE Sleep/Idle mode LTE supply current (without USB connection) Sleep mode Typical: 1.56 Idle mode Typical: 22 UMTS Talk WCDMA B2 @Power 22dBm WCDMA B5 @Power 23.
Smart Machine Smart Decision 6 SMT Production Guide 6.1 Top and Bottom View of Module Figure 32: Top and bottom view of Module 6.2 Typical SMT Reflow Profile SIMCom provides a typical soldering profile. Therefore the soldering profile shown below is only a generic recommendation and should be adjusted to the specific application and manufacturing constraints. Figure 33: The ramp-soak-spike Reflow Profile of Module Note: For more details about secondary SMT, please refer to the document [21].
Smart Machine Smart Decision 6.3 Moisture Sensitivity Level (MSL) Module is qualified to Moisture Sensitivity Level (MSL) 3 in accordance with JEDEC J-STD-033. If the prescribed time limit is exceeded, users should bake modules for 192 hours in drying equipment (<5% RH) at 40+5/-0°C, or 72 hours at 85+5/-5°C. Note that plastic tray is not heat-resistant, and only can be baked at 45° C.
Smart Machine Smart Decision 7 Packaging Module module support tray packaging. Figure 34: Packaging introduce Module tray drawing： Figure 35: Module tray drawing introduce Table 36: Tray size Length（±3mm） Width（±3mm） Module number 242.0 161.0 15 Small carton drawing： SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision Figure 36: Small carton drawing introduce Table 37: Small Carton size Length（±10mm） Width（±10mm） Height（±10mm） Module number 270 180 120 15*20=300 Big carton drawing： Figure 37: Big carton drawing introduce Table 38: Big carton size Length（±10mm） Width（±10mm） Height（±10mm） Module number 380 280 280 300*4=1200 SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision Appendix A. Reference Design Figure 38: Reference design Note: The UART port suggest to be used by isolated circuit . SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision B. Coding Schemes and Maximum Net Data Rates over Air Interface Table 39: Coding schemes and maximum net data rates over air interface Multislot definition(GPRS/EDGE) Slot class DL slot number UL slot number Active slot number 1 2 3 4 5 6 7 8 9 10 11 12 1 2 2 3 2 3 3 4 3 4 4 4 1 1 2 1 2 2 3 1 2 2 3 4 2 3 3 4 4 4 4 5 5 5 5 5 GPRS coding scheme Max data rata（4 slots） Modulation type CS 1 = 9.05 kb/s / time slot 36.2 kb/s GMSK CS 2 = 13.4 kb/s / time slot 53.
Smart Machine Smart Decision Category 9 10.2Mbps 16QAM,QPSK Category 10 14.4Mbps 16QAM,QPSK Category 11 0.9Mbps QPSK Category 12 1.8Mbps QPSK Category 13 17.6Mbps 64QAM Category 14 21.1Mbps 64QAM Category 15 23.4Mbps 16QAM Category 16 28Mbps 16QAM Category 17 23.4Mbps 64QAM Category 18 28Mbps 64QAM Category 19 35.5Mbps 64QAM Category 20 42Mbps 64QAM Category 21 23.4Mbps 16QAM Category 22 28Mbps 16QAM Category 23 35.5Mbps 64QAM Category 24 42.
Smart Machine Smart Decision C. Related Documents Table 40: Related documents SN [1] [2] Title SIM7X00 Series_AT Command Manual_V1.xx ITU-T Draft new recommendationV.25ter [3] GSM 07.07 [4] GSM 07.10 [5] GSM 07.05 [6] GSM 11.14 [7] GSM 11.11 [8] GSM 03.38 [9] GSM 11.10 [10] 3GPP TS 51.010-1 [11] 3GPP TS 34.124 [12] 3GPP TS 34.121 [13] 3GPP TS 34.123-1 [14] 3GPP TS 34.123-3 [15] EN 301 908-02 V2.2.1 [16] EN 301 489-24 V1.2.1 [17] IEC/EN60950-1(2001) [18] 3GPP TS 51.
Smart Machine Smart Decision [19] GCF-CC V3.23.1 [20] 2002/95/EC [21] Module secondary-SMT-UGD-V1.xx [22] SIM7X00 Series_UART_Application Note_V1.xx [23] [24] [25] SIM7X00 Series_USB AUDIO_Application Note_V1.xx Antenna design guidelines for diversity receiver system SIM7X00 Series_Sleep Mode_ Application Note_V1.xx SIM7600A-H_User Manual_V1.
Smart Machine Smart Decision D.
Smart Machine Smart Decision SMS SPI SMPS TDMA TE TX UART VSWR SM NC EDGE HSDPA HSUPA ZIF WCDMA VCTCXO USIM UMTS UART Short Message Service serial peripheral interface Switched-mode power supply Time Division Multiple Access Terminal Equipment, also referred to as DTE Transmit Direction Universal Asynchronous Receiver & Transmitter Voltage Standing Wave Ratio SIM phonebook Not connect Enhanced data rates for GSM evolution High Speed Downlink Packet Access High Speed Uplink Packet Access Zero intermediate
Smart Machine Smart Decision E. Safety Caution Table 42: Safety caution Marks Requirements When in a hospital or other health care facility, observe the restrictions about the use of mobiles. Switch the cellular terminal or mobile off, medical equipment may be sensitive and not operate normally due to RF energy interference. Switch off the cellular terminal or mobile before boarding an aircraft. Make sure it is switched off.
Smart Machine Smart Decision Contact us: Shanghai SIMCom Wireless Solutions Ltd. Add: SIM Technology Building, No.633, Jinzhong Road, Changning District, Shanghai P.R. China 200335 Tel：+86 21 3235 3300 Fax：+86 21 3235 3020 URL：www.simcomm2m.com SIM7600A-H_User Manual_V1.
