User's Manual

PropertyofTCPInc
ProprietaryandConfidential

Group1LED 1,2
Group2LED 1,2
Group3LED 1,2
Group4LED 1,2
Group1‐4Button 1,2
SliderUp 1,2
SliderDown 1,2
RFSubsystem 1,2,3,4
Power(Battery)Subsystem 1,2,3,4

Figure11FunctionalTestRemoteControlComponentCoverage

Test1:
Testifyoucanaddonenew/resetlightbulbtothenetwork(kitdoesn’thaveGateway):
a. Turnpowertothelightfixtureon.Checkifthebulbbeginstobrightenanddim.
b. RemovethebatterycoverfromthebackoftheremotecontrolsothatyouhaveaccesstotheProgrambutton.
c. Ontheremotecontrol,pressandholdgroupbutton“1”forthree
seconds.Whenthelightbulbisfoundandisbeingconfiguredbytheremotecontrol,theremotecontrol’sprimaryindicatorlightflashesrapidly.
d.
Whenonelightbulbturnsonatfullbrightness,returntheremotecontrolbacktonormaloperationbypressingtheProgrambutton.
e. Pressbutton“1”totestifitcanturnon,turnoff,dimandbrightenthebulb.Pressthegroupallbutton“1‐4”totestifitcanworkaswell.
f. Repeatandtestifothernewlightbulbscanbeaddedtobutton“2”,“3”and
“4”separatelyfollowingthesameprocedure.

Test1: 测试是否可以成功添加一个新的/重置的灯泡到遥控灯网络（不含 Gateway 组合）
a. 供电到灯泡，检查该灯泡是否开始明暗闪烁。
b. 卸掉遥控器电池后盖，露出程序键。
c. 长按遥控器上“1”号键 3 秒钟。当灯泡被遥控器识别并配对时，遥控器上的主指示灯会快速闪烁。
d.
当被识别的灯泡变到稳定的最大亮度时，再按程序键，使遥控器回到正常操作状态。
e. 测试“1”号键是否可以开，关，调暗，调亮被配对的灯泡。按“1‐4”全组键，测试该键是否可以同样工作。
f. 重复测试实验，检查其他键“2 ”，“3”，和键“4”是否可以成功添加灯泡。



Test2: Testifyoucanaddmultiplelightbulbstothesamegroupnumber(kitdoesn’thaveGateway):
a. Turnpowertothelightfixtureon.Checkifthebulbbeginstobrightenanddim.
b. Removethe
batterycoverfromthebackoftheremotecontrolsothatyouhaveaccesstotheProgrambutton.
c. Ontheremotecontrol,pressandholdgroupbutton“1”forthreeseconds.Whenthelightbulbisfoundandisbeingconfiguredbytheremotecontrol,theremotecontrol’sprimary
indicatorlightflashesrapidly.
d. Whenonelightbulbturnsonatfullbrightness,repeatstepc
toaddanotherbulbtogroupbutton“1”.
e.
ReturntheremotecontrolbacktonormaloperationbypressingtheProgrambutton.
f. Pressbutton“1”totestifitcanturnon,turnoff,dimandbrightenallthebulbs.Pressthegroupallbutton“1‐4”totestifitcanworkaswell.
g. Repeatthistesttoaddmorelightbulbstothesamegroupnumber.