LTE CPE Quick Start
1．Getting to know your router ①Power indicator On: the device is powered on. Steady blue: power on the device by the battery or the power adapter Blue flicker: charging the battery Steady blue: finish charging Red flicker：battery power is less than 10% Off: the device is powered off.
②network mode indicator Steady blue：connected to a 4G/3G network. Blue flicker：4G/3G data transfer. Steady red： ---The SIM card is not recognized, the PIN has not been entered, or the PIN verification failed. ---Failed to connect to a mobile network or an Ethernet network. Red flicker：Looking for network. ③Wi-Fi indicator Steady on：Wi-Fi turned on. Off: Wi-Fi turned off. ④LAN indicator Steady on：At least one of the LAN ports is connected to a device.
⑨power button ⑩Power port ⑪WPS/Reset button Press the button to power the device on or off; Connect to compatible power adapter. Press for 2 seconds to active WPS connection when Wi-Fi is turned on. !! Restoring the default settings of the device will erase all previous settings. When the device is powered on ,press the reset button and hold for about 8 seconds to restore the device to its factory settings. After the factory defaults are restored, the device will restart automatically.
1. Power off the device. 2.Slide off the battery back cover. 3.Insert the SIM card into the card slot. 4.Close the battery back cover.
！ ！Do not remove the SIM card when it is in use, Doing so will affect the performance of your device and data stored on the SIM card may be lost. Step 2：Installing the battery (optional) 1. Power off the device. 2. Slide off the battery back cover. 3.Insert the battery into the battery slot, connect the battery with the device by the connector. 4.Close the battery back cover.
Step 3: Charging the Battery (optional) 1.Power off the device. 2.Slide off the battery back cover. 3.Insert the battery into the battery slot, connect the battery with the device by the connector. 4.Connect the power adapter to the device.(you can power on the device to charge) If the device has not been used for a long time or if the battery is fully depleted, the device may not power on immediately after the charger is plugged in.
！ ！To prevent interference caused by radio signals ,place the device at least 1 meter away from telephone and other electrical devices. Do not change another unexpected power adapter unless manufacturer provide. For details about the details about the specific adapter model, contact an authorized dealer. Once connected to a power outlet, press the power button to power the device on . 3．Setting up a Wi-Fi connection ！ ！Make sure your client (computer, tablet, or smart phone)also supports Wi-Fi.
Step 2: Recording the SSID and Wi-Fi key The default SSID and Wi-Fi key are printed on the device's bottom label. ！！To prevent unauthorized parties from accessing your Wi-Fi network, it is recommended that you change the SSID and Wi-Fi key from time to time. For details, see the help information on the web management page. Step 3: Setting up a Wi-Fi connection on your client Method 1: Setting up a Wi-Fi connection manually 1. From your Wi-Fi enabled client, scan for wireless networks in your area. 2.
!! For instructions about how to enable a WPS connection on the client, see the client's user guide. 4．Configuring your device 1. After a client is connected to the device through Wi-Fi or LAN port, launch a browser on the client and visit http://192.168.1.1. 2. Enter the user name and password to log in to the web management page. The default user name and password are printed on the device's bottom label. 3. Follow the quick setup wizard to check or set network connection parameters step by step.
！ ！Figures in this guide are for your reference only. Specific models may vary slightly, contact your service provider for more detailed information. 6．Safety information This section contains important information about the operation of your device. It also contains information about how to use the device safely. Read this information carefully before using your device. Electronic device Do not use your device if using the device is prohibited.
stored (in a gas station, oil depot, or chemical plant, for example). Using your device in these environments increases the risk of explosion or fire. In addition, follow the instructions indicated in text or symbols. Do not store or transport the device in containers with flammable liquids, gases, or explosives. Operating environment Avoid dusty, damp, or dirty environments. Avoid magnetic fields. Using the device in these environments may result in circuit malfunctions.
dissipation, such as a box or bag. To protect your device or accessories from fire or electrical shock hazards, avoid rain and moisture. Keep the device away from sources of heat and fire, such as a heater, microwave oven, stove, water heater, radiator, or candle. Do not place any object, such as a candle or a water container, on the device. If any foreign object or liquid enters the device, immediately stop using it, power it off, and remove all cables connected to it.
the device should be greater than 30 cm. Child's safety Comply with all precautions with regard to child's safety. Letting children play with the device or its accessories may be dangerous. The device includes detachable parts that may present a choking hazard. Keep away from children. The device and its accessories are not intended for use by children. Children should only use the device with adult supervision.
once. Continued use may lead to electric shocks, short circuits, or fire. Do not touch the power cord with wet hands or pull the power cord to disconnect the power adapter. Do not touch the device or the power adapter with wet hands. Doing so may lead to short circuits, malfunctions, or electric shocks. If your power adapter has been exposed to water, other liquids, or excessive moisture, take it to an authorized service center for inspection.
emits smoke or any unusual sound or smell), immediately stop using it, power it off, remove all cables connected to it, and contact an authorized service center. Do not trample, pull, or excessively bend any cable. Doing so may damage the cable, causing the device to malfunction. Before you clean or maintain the device, stop using it, stop all applications, and disconnect all cables connected to it.
Warning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
