Data Sheet
Table Of Contents
- Abstract
- 1. Introduction
- 2. Characteristics
- 3. Pin Definition
- 4. System memory Space
- 5. ATE（RF Test Mode）
- 5.1. Wi-Fi ATE Command
- 5.1.1. Start MP mode
- 5.1.2. Stop MP mode
- 5.1.3. Set Tx rate
- 5.1.4. Set operational channel
- 5.1.5. Set operational bandwidth
- 5.1.6. Set Tx power
- 5.1.7. Set antenna for Tx
- 5.1.8. Set antenna for Rx
- 5.1.9. Start air Rx mode
- 5.1.10. Start continuous Tx mode
- 5.1.11. Query air Rx statistics
- 5.1.12. Reset air Tx/Rx statistics
- 5.2. Bluetooth ATE Command（TBD）
- 5.3. Example Command
- 5.1. Wi-Fi ATE Command
- 6. Flash Programming
- 7. Electrical Parameters
- 8. RF Parameter
- 9. Antenna Information
- 10. Dimensions and Production Guidance
- 11. Production Guidelines
- 12. FCC and IC Information
- 12.1. FCC Warning
- 12.2. IC warning
- 12.3. Trace antenna designs
- 12.4. RF exposure considerations
- 12.5. Antennas
- 12.6. Label and compliance information
- 12.7. Information on test modes and additional testing requirements5
- 12.8. Additional testing, Part 15 Subpart B disclaimer
- 12.9. The module is limited to OEM installation ONLY.
- 12.10. The OEM integrator is responsible for ensuring that the end-user has no manual instructions to remove or install module.
- 12.11. The module is limited to installation in mobile or fixed applications
- 13. Packaging and Label Information
- 14. Sales and Technical Support Information
EMC3380 Series Wireless Module Data Manual
Copyright of Shanghai MXCHIP Information Technology Co., Ltd.
26
iwpriv mp_txpower patha=44,pathb=44 //set path A and path B Tx power level
iwpriv mp_rate 108 //set OFDM data rate to 54Mbps,e x: CCK 1M = 2, CCK 5.5M = 11,
KK, OFDM54M = 108 N Mode: MCS0 = 128, MCS1 = 129…..etc.
iwpriv mp_ctx background //start continuous Tx
iwpriv mp_ctx stop //stop continuous Tx
iwpriv mp_stop //exit MP mode
continuous message sending test
iwpriv mp_start //enter MP mode
iwpriv mp_channel 1 //set channel to 1 . 2, 3, 4~11 etc.
iwpriv mp_bandwidth 40M=0,shortGI=0 //set 20M mode and long GI
iwpriv mp_ant_tx a //select antenna A for operation
iwpriv mp_txpower patha=44,pathb=44 //set path A and path B Tx power level
iwpriv mp_rate 108 //set OFDM data rate to 54Mbps, ex: CCK 1M = 2, CCK 5.5M = 11,
KK, OFDM54M = 108 N Mode: MCS0 = 128, MCS1= 129….. etc.
iwpriv mp_ctx background,pkt //start packet continuous Tx
iwpriv mp_ctx stop //stop continuous Tx
carrier suppression test
iwpriv mp_start //enter MP mode
iwpriv mp_channel 1 //set channel to 1 . 2, 3, 4~11 etc.
iwpriv mp_bandwidth 40M=0,shortGI=0 //set 20M mode and long GI
iwpriv mp_ant_tx a //select antenna A for operation
iwpriv mp_txpower patha=44,pathb=44 //set path A and path B Tx power level
iwpriv mp_rate 108 //set OFDM data rate to 54Mbps,ex: CCK 1M = 2, CCK 5.5M = 11,
KK, OFDM54M = 108 N Mode: MCS0 = 128, MCS1 = 129…..etc.
iwpriv mp_ctx background,cs //start sending carrier suppression signal
iwpriv mp_ctx stop //stop continuous Tx
iwpriv mp_stop
Single Tone Signal sending test
iwpriv mp_start //enter MP mode
iwpriv mp_channel 1 //set channel to 1 . 2, 3, 4~11 etc.
iwpriv mp_bandwidth 40M=0,shortGI=0 //set 20M mode and long GI
iwpriv mp_ant_tx a //select antenna A for operation