FS020U USB MODEM User Manual
Table of Contents User Manual ................................................................................. 1 1 Introduction .............................................................................. 3 2 Description for Client Interface ............................................... 4 Activate Client ...................................................................... 4 Introduction to Interface........................................................ 5 3 Connection ...............................
1 Introduction The product is designed to enable PC users access to the Internet via GPRS/EDGE/UMTS/HSPA/LTE networks. It uses a standard USB interface for a fast simple connection to your PC.
2 Description for Client Interface Activate Client To activate client, please double-click the shortcut icon of client on the desktop.
Introduction to Interface 1. Function Icon The definition of function icon provided by client is as follows: Shortcut icon Description Connection Setting Network recording 2.
found. Display “No (U)SIM ” when the (U)SIM can’t be found. Device and Display “Invalid” when the (U)SIM is invalid. Network Display “Searching” when searching the information network. Display “No service” when the network can’t be found. Display the name of network operator after successful network registration. Network Indicates network has been hasn’t been connected. connection status Indicates network connected. 3.
3 Connection Auto-connection and customized-connection modes are provided to access to the network. Automatically connect to the network If using the default connection configuration, you should connect by dialing according to the default connection profiles. 1. Connect Select connection mode: click on for auto connection. After the completion of connection, bar will turn into under the window status . 2. Disconnect Click on to disconnect the connection.
Note: Please contact the network operator for profile information. 2. Predefined List Select a profile in the predefined list and then add it into the connection profile list. 3. Edit Select one profile in the available list and then to edit. 4. Delete Select one profile in the available list and then to delete it. 5. Set default Select one item from the list of available connection profile(s).
4 Setting Connection Click on to display available connection profile. 1. Sound Enabled/Disable sound prompts when Internet connection or disconnecting. 2. Connection Setting Please refer to “Connection”. For customized-connection network information PIN Management 1. Enabled PIN Click on to select Enable/Disable and activate PIN launching or close dialog box; Input the correct PIN; Click on to prompt the launching or closing PIN. 2.
Input new PIN and re-input for confirmation, and click on . Note: It can be allowed only the PIN enabled. Language Setting Click on to select language, and the window will display the selected language when restart the client. Network Connection Network Mode Click on to select, network mode defaulted is auto; Click on /< 1x only >/< 3G only > to relevant network mode. Diagnostics Click on < Diagnostics > to launch the window of diagnosis information.
5 Network recording Network recording The user can view the network recording. 6 FAQ 1. 2. Q: Which operation systems does the software support? A: It supports Windows XP, Windows Vista, Windows 7. Q: I cannot install applications？ A: The reasons are shown below: 1. If automatic installation unfinished, please check whether the antivirus and security software is working. If it is, close it and reinstall.
3. Q: The (U)SIM does not register any networks A: The reasons are shown below: 1. Unstable local signal; 2. The software is an old version; 3. Hardware problem. You may: 1. Try to logon from another location; 2. Update the software; 3. Check the hardware or use another data card and retry. 4. Q: Why does the prompt “Unavailable connection profile” appear? 5. A: Please add a connection profile manually.
(U)SIM 8. Q: Does it support roaming? A: This depends on the local operator. Please check with your local operator or service provider. Please make sure the temperature for device will not be higher than 55 ˚C The device could be used with a separation distance of 0.5cm to the human body. Assessment of compliance of the product with the requirements relating to the Radio and Telecommunication Terminal (EC Directive 1999/5/EC) Equipment Directive was performed by PHOENIX TESTLAB (Notified Body No.
FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. RF Exposure Information (SAR) This device meets the government’s requirements for exposure to radio waves.
output. SAR compliance has been established in the host product(s) (laptop computers), tested at 5mm separation distance to the human body, and tested with USB slot configurations including Horizontal-UP, Horizontal-Down, Vertical-Front, Vertical-Back. This device can be used in host product(s) with substantially similar physical dimensions, construction, and electrical and RF characteristics. The highest SAR value, tested per FCC RF exposure guidelines for USB dongle, as described in this user guide, is 1.
