NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD NAKe series Non-contact Level switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD Address: Room 1611, Lijing Yangguang Building, NO.19 Wuning Road, Shanghai,China Web Site:www.china-huibo.cn Email: huiboshanghai@163.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD I. Preparation 1．#50 Angle Iron is most commonly used as Support of NAKe series Non-contact Level Switch. #50 Bar Iron and Channel Iron are also used by many users. 2. The length and opening size of the iron are shown below: 150 mm The length left outside the ash bucket insulation layer is no less than that of 350mm Bar iron Angle iron 25m m Channel iron II. Welding position on the containers 1.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD ①、Alarm level of Ash level in the container ②、Installation and maintenance convenience ③、Those with heating panels should avoid them. ④、Those with vibrators should avoid them 2.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD The angle iron is horizontally welded on the outer wall of the container. Angle iron should passes through the insulating layer, if there is. Or, put on the insulation after angle iron is welded.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD ③、Open the terminal Cover(with glass window). Screw up the Antenna and connect the Antenna from inside the terminal Cover. ③、Put the Level Switch into the clamp rings, with the terminals end facing out, the front end (stainless steel) pointing at the container, the distance 30-50mm from the insulation layer to the front end, and the waterproof cable lock downward.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD 3. Application of ash hopper Angle iron Clamp Rings Level Switch Insulating layer Angle iron Coal Ash Clamp Rings Ash Hopper Wall Level Switch 4. The Application of Coal Bunker Address: Room 1611, Lijing Yangguang Building, NO.19 Wuning Road, Shanghai,China Web Site:www.china-huibo.cn Email: huiboshanghai@163.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD Coal bunker wall 5. Application of coal ash pump Connect to Ash hopper Clamp rings Angle iron Ash Level Switch Ash pump Address: Room 1611, Lijing Yangguang Building, NO.19 Wuning Road, Shanghai,China Web Site:www.china-huibo.cn Email: huiboshanghai@163.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD 6. Application of alarm cinder level under the water Water Level Switch Angle iron Dewatering bin wall Dregs IV. Level Switch Wiring 1. Preparation of wiring: ①、Rotate the Terminal Cover of the Level Switch counterclockwise, while holding the cable lock. ②、 Unplug the power cable’s sheath about 50mm, Strip each core wire and exposes the copper core about the 10mm.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD ③、Tighten the cable lock to ensure that the seal is tight. If the seal is not strong enough, apply waterproof self-adhesive tape to wrap tightly 2. Wiring Terminals are screw free. Single core copper wire can be inserted directly. Multi-core soft copper wire should be welded together before inserted.
NAKe Series Non-contact Level Switch Installation Instruction SHANGHAI HUIBO AUTOMATIC GAUGE CO., LTD prevent dust and moisture affected the life of the level switch. FCC Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
