User's Manual

ManualsBrandsShanghai Huace Navigation Technology ManualsElectronicsHandheld GPS receiver

LT400HS | GETTING STARTED GUIDE

GNSS/GIS HANDHELD RECEIVER

Summary of content (19 pages)

PAGE 1
LT400HS | GETTING STARTED GUIDE GNSS/GIS HANDHELD RECEIVER
PAGE 2
Copyright Copyright 2009-2013 CHC Shanghai HuaCe Navigation Technology Ltd. All rights reserved. The CHC is trademark of Shanghai Huace Navigation Technology Limited. All other trademarks are the property of their respective owners. Trademarks All product and brand names mentioned in this publication are trademarks of their respective holders. Safety Warnings The Global Positioning System (GPS) is operated by the U.S.
PAGE 3
Changes or modifications made to this equipment not expressly approved by Shanghai Huace Navigation Technology Ltd. may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 4
Table of Contents 1. 2. Introduction.......................................................................................................................................1 1.1. Technical Assistance............................................................................................................ 1 1.2. Your Comments................................................................................................................... 1 Overview.....................................................
PAGE 5
1. INTRODUCTION Thank you for choosing LT400HS GNSS Handheld Receiver. This Getting Started Guide will provide useful information about your receiver. It will also guide you through your first steps of using LT400HS in the field. 1.1. TECHNICAL ASSISTANCE If you have a problem and cannot find the information you need in the product documentation, contact your local dealer from which you purchased the LT400HS. Alternatively, please request technical support using the CHC Website at (www.chcnav.
PAGE 6
2. OVERVIEW 2.1. FEATURES LT400HS is a handheld GNSS RTK receiver and a precision GIS data collector that incorporate a survey-grade professional L1/L2 GNSS core engine as well as Microsoft Windows Mobile® 6.1 operating system. LT400HS comes in a rugged design suitable for all your demanding survey and construction environment as well as numerous mapping applications. LT400HS is optimized to run with Carlson SurvCE® 3 field survey software and/or DigiTerra Explorer 7 GIS data collection software. 2.2.
PAGE 7
- GSM/GPRS (850/900/1800/1900 MHz) phone and data transmission - Bluetooth V2.1 Class 3 - 802.11 b/g wireless LAN - Built-in microphone and speaker - RTCM and NMEA 0183 protocol support Physical - Size (L x W x H): 158 mm x 85 mm x 25mm - Weight: 0.600 Kg with battery - Working Temperature: -20 °C to +60 °C - Storage Temperature: -30 °C to +70°C - Dust proof: IP65 - Shock : survive a 1.
PAGE 8
3.
PAGE 9
Rear view External Antenna Connector Camera Latch Battery Data cable Connector  Page 5
PAGE 10
4. FIRST -TIME USE 4.1. INSERTING THE BATTERY , STORAGE CARD AND SIM CARD  Lift the latch of the battery and turn it counter-clockwise to the unlock position (vertical). Then, detach the battery from the device. See Figure 1. Lift the latch Figure 1  Two slots are located at the battery compartment: the SIM card slot and TF card slot. Please insert the cards according to the icons engraved on the interior of the battery compartment.
PAGE 11
4.3. TURNING THE DEVICE ON /OFF OR STANDBY  Make sure that the receiver battery is charged OR that the LT400HS is connected to PC via data cable (internal battery shall always be installed).  Press the power button for 3-5 seconds to turn on/off the device. Note: If you need to perform soft reset, use the stylus to press the Reset key (located beside the power button). This will re-boot the Windows Mobile operating system. Before operation, please make sure your task performing has been stored. 4.4.
PAGE 12
4.5. INSTALLING SOFTWARE  First, make sure LT400HS is connected and synchronized with your computer.  Select and click on the installation file to install, or if the installation file runs only on LT400HS, please copy the file to LT400HS, double click it to install. You can also copy files to LT400HS’s relevant location to save it.  Choose a location to install the program, click the Install icon to start installation.
PAGE 13
 Open GNSSViewer software: o Run “My Device”-“Program Files”-“GNSSViewer”. o The symbol “GNSSViewer” will appearing at the bottom right corner of the main screen when the software is running. Double click the icon will take you come back to software interface. o Choose Com6 and 57600 for connecting GPS Port.
PAGE 14
4.8. USING THE CAMERA  Press the Camera key to enter in the picture taking mode.  Press the Camera Key again to take a picture.  Click the OK icon on the top right corner to exit. 4.9. ESTABLISHING WIRELESS CONNECTION (B LUETOOTH /W I-F I)  Using Bluetooth 1） Go to Start-->Settings-->Connections-->Wireless Manager. 2） Click on the icon on the right side of Bluetooth to open Bluetooth function. 3） Go to Start-->Settings-->Connections-->Bluetooth.
PAGE 15
5. GETTING STARTED WITH SURV CE 3 Configure the LT400HS 1. Go to Start menu --> Settings --> System 2. Select External GPS icon 3. On the Software port tab: select COM4 4. Then on the Hardware port tab: select COM3 and Baud: 57600 Start SurvCE 3: 1. Go to GPS Rover, in Current tab--> choose Manufacturer CHC, Model: LT400HS 2. In Comms tab, select Cable, Port COM3 and Baud 57600 automatically. 3.
PAGE 16
6. GETTING STARTED WITH DIGI TERRA EXPLORER 7 1. 2. Go to Start menu --> Settings --> System Select External GPS icon 3. On the Software port tab: select COM4 4. Then on the Hardware port tab: select COM3 and Baud: 57600 Start DigiTerra Explorer 7: 1. Go to Settings > GNSS tab Port: COM3 Baud: 57600 2. If you intend to use RTCM corrections go to the Settings > NTRIP tab and set Port: COM4 and Baud: 57600 3.
PAGE 17
7. OUTPUTTING NMEA 0183 DATA FROM THE 9- PIN PORT The LT400HS can output the default NMEA 0183 V2.2 messages at 1Hz: GPGGA, GPGSA, GPGSV, GPGST, GPRMC. 1. Go to Start menu --> Settings --> System 2. Select External GPS icon 3. On the Software port tab: select COM6 4. Then on the Hardware port tab: select COM3 and Baud: 57600 To set NTRIP Connection if required, run GNSSViewer: 1. Select BoardType-->NovAtel, GPS Port-->COM6, and BaudRate-->57600, press OK. 2.
PAGE 18
8. FREQUENT SETTINGS  Stylus Setting Go to Start-->Settings-->System-->Screen Click Align Screen to start the stylus setting.  Backlight Setting Go to Start-->Settings-->System -->Backlight, Adjust settings according to your requirements.  Power Setting Go to Start-->Settings-->System-->Power-->Advanced, Adjust settings according to your requirements.  Remove Programs Go to Start-->Settings-->System-->Remove Programs, Choose the relevant program then click Remove.
PAGE 19
CHC - Shanghai HuaCE Navigation Technology Ltd. Building 35, n° 680 Guiping Road 200233 Shanghai – China Tel : +86 21 542 60 273 Fax : +86 21 649 50 963 Email : sales@chcnav.com | www.chcnav.