AUTO GENUINE PRODUCTS Application Models: Buses & Trucks & Trailers & OTR ● Your purchase of genuine products from Baolong is greatly appreciated. ● Please read this user’s manual carefully to ensure proper operation. User’s Manual for TPMS203 The Fifth Edition Part No. Ma Sensing Pressure Standard Cold Inflation Pressure Low Pressure Warning Limit High Pressure Warning Limit TPMS203 12.8Bar 185PSI 5.0~9.8Bar 72.
ATTENTION Default values have been assigned to each axle for the following: Standard Cold Inflation Pressure (SCIP) – you can find on the tyre sidewall Baseline Pressure – 6Bar / 87PSI (default), can be reset by user according to SCIP Low Pressure Warning – -20% deviation from baseline pressure High Pressure Warning – +30% deviation from baseline pressure High Temperature Warning – Over 80℃ / 176℉ Leakage Warning – Air lose is more than 0.33 Bar / 4.
TABLE OF CONTENTS Part ⅠINTRODUCTION..........................................................................................................................1 1.1 DISPLAY ...........................................................................................................................................1 1.2 TRAILER BOX ....................................................................................................................................2 1.3 VEHICLE ID BOX ..............................
Part ⅠINTRODUCTION 1.1 Display The display monitors pressure and temperature information of each tyre in a visual form continuously. This system can monitor up to 6 axles as well as enable baseline pressure adjustment to suit different tyre specifications.
1.2 Trailer Box The Trailer Box is mounted onto the trailer to read trailer tyres’ information and relay data to the display wirelessly. Controls and Indicators Receiving Antenna Transmitting Antenna Switch Set Key Functions Collect trailer tyres’ information Send trailer tyres’ information to display wirelessly Turn on or off the trailer box 1) Press it for 8 seconds (red light) to set baseline pressures of trailer. 2) Press it for 4 seconds (green light) to register the trailer. 1.
from all transmitters has been received, the display will show the data on the screen until a warning condition is detected. NOTE: Before doing the following operations, please ensure that ID modules are plugged. 2.2 Setting the Baseline Pressure The baseline pressure has been set in the factory at 6 Bar (87PSI) for all wheel positions. We recommend that you set the baseline pressure at the standard cold inflation pressure recommended by the tyre manufacturer.
pressure automatically. The Trailer Box will exit setting baseline pressure mode automatically when signal from all trailer transmitters are received. NOTE: After the display has received all transmitters’ pressure value, you can press the SET Key on the display to look up all tyres’ baseline pressures, axle by axle. 2.3 Checking Tyre Conditions 1.
2.4 Setting Time We have set the GMT +8 as default, please reset if needed. 1. Press Axle Switch for 8 seconds to get into Time Setting Mode and you will hear a “DI” sound. 2. Press Axle Switch swiftly to look up the time “year-month-date-day-hour-minute” value circularly. The following time is 22:57, Tuesday, May 25, 2010. 3. Press Pressure & Temp. Switch to change the time value. 4. You must press Axle Switch for 8 seconds to exit time setting mode, if not, the time setting will take effect.
Part Ⅲ WARNINGS NOTE: Warning indicates that you are operating your vehicle in a dangerous condition. When the abnormality icon illuminates, STOP AND CHECK your tyre(s) as soon as possible and inflate them to the proper pressure. The system has five types of warning modes: ● 20% below the baseline pressure for the Low Pressure Warning; ● 30% above the baseline pressure for the High Pressure Warning; ● Over 0.33 Bar / 4.
① Display shows the pressure of axle with abnormal tyre; ② Warning sound “Di-Di”; ③ Leakage icon “ ” appears; ④ The value of abnormal tyre position flashes. The figure 6.85 is flashing, that means “2A” tyre is leaking. 3.4 High Temperature Warning When temperature inside tyre is higher than 80℃ (176℉): ① Display shows the temperature of axle with abnormal tyre; ② Warning sound “Di-Di-Di”; ③ Abnormality icon “ ” appears; ④ The value of abnormal tyre position flashes.
Part Ⅳ TRAILER CHANGE AND REGISTERATION 1. Turn off the trailer box on trailer ①, disconnect the tractor and trailer ①. 2. Connect the trailer ② with tractor. 3. Register trailer ② Registration between Trailer Box and Vehicle ID Box can be automatically established. NOTE: During the automatic registration, if the Trailer Box light remains green and does not turn off, please also try manual registration as below. 1) Turn on the Trailer Box, and the indicator light becomes green.
Rotate the wheels between position “2A” and “2D” * Back of Display * Back of Trailer Box Change their corresponding ID modules’ position, restart display and trailer box Part Ⅵ REPLACEMENT OF A DAMAGED TRANSMITTER After replacing the damaged transmitter, you should also replace its ID module. 1. Replace the malfunctioned transmitter 2. Replace the corresponding ID module 3.
Part Ⅷ PARAMETERS OF THE PRODUCT Display Power Consumption: 360 mW (Regular); 1200mW (Max) Power Supply: DC 12/24 Volt Weight: 231g (8.15 oz.) Dimensions: 15.5 x 6.2 x 2.3 cm (6.1 x 2.4 x 0.9 inch) Operating Temperature Range: -40℃ to 85℃ (-40℉ to 185℉) Pressure Resolution: 0.01Bar (0.1PSI) Temperature Resolution: 1℃ (1℉) Transmitter Weight: 78g (2.47oz.) Dimensions: 8.3 x 3.1 x 2.5 cm (3.27x1.22x0.
Part Ⅸ TROUBLE SHOOTING Problems Both pressure value and temperature value of all tyres are "000" shown on the display Possible Reasons Problems of antenna connection The antenna is damaged (if all transmitters are well) Display malfunction Problem of transmitter The pressure and temperature values are ”000” at some transmitter positions (After start the display) The pressure value is “000”, but temperature value is normal.
Part Ⅹ CERTIFICATES 10.1 FCC and IC's Authentication Announcement This device has been tested and found compliance with applicable the technical standards of FCC Rules: 1) FCC PART 15C; 2) ANSI C63.4:2003; and also those of IC rules: 1) RSS210 Issue 8; 2) RSSGEN Issue 3; 3) ANSI C63.4:2003.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. Déclaration d'exposition aux radiations Cetéquipementestconforme Canada limitesd'exposition aux radiations dans un environnement non contrôlé. 10.2 European Regulations Announcement This device complies with all European Electromagnetic compatibility regulations (2009/19/EC).
devices. This limited warranty covers only repair, replacement or refund for defective BAOLONG products. All other express or implied warranties, liability for incidental, special, consequential or any other damages including but not limited to, economic loss, lost revenue, lost profits, or loss of use or damage to other property, hereby are expressly disclaimed regardless of whether they were reasonably foreseeable, or whether seller had knowledge that they could occur.
Products replaced under warranty are covered hereunder by the remaining portion of the original warranty period or 12 months, whichever is greater. BAOLONG obligation to satisfy a warranty claim is subject to the following conditions: (1) Dated proof of purchase is provided (2) All such claims must be submitted to BAOLONG no later than sixty (60) days from the date of the failure (the date BAOLONG receives the complaint), and must be accompanied by a Warranty Claim Form (Appendix 1).
(2) Claims is submitted to BAOLONG over sixty (60) days from the date of the failure (the date BAOLONG receives the complaint); (3) No or incomplete Warranty Claim Form (Appendix 1) (4) Product was not returned for inspection as requested (5) Product inspection does not indicate a failure (6) Failure occurred beyond warranty period (7) Product damage in transit.
Did you accelerate the speed from 0 to 25km/h fastly Yes No Did you ever change the original transmitter? Yes No Did you do tyre repair recently? Yes No Detailed Description of Defective Part What problems happen when driving or stopping? What shows on display? (pressure, temperature backlight, icon, buzzer) Frequency of Problem Rare Very often Other Description: Distributor Signature: Parts Needed to be Replaced (Must be returned to Baolong) Part Name and S/N Number Quantity 17
Important Claim must be submitted within 60 days after failure Fill out one claim form for each claim Dated proof of purchase is provided Some pictures of defective product/part are helpful for remedy. Shanghai Baolong Automotive Corporation 5500, Shenzhuan Rd., Songjiang, Shanghai 201619, China Tel.: +86-21-31273333 Fax: +86-21-31190319 E-mail: sbic@chinabaolong.net sbic@baolong.biz Web: www.baolong.
