INSTALLATION MANUAL Single Station Thermal Printer Model: BTP-R880NP z This printer has been manufactured and branded for ORIENT Technologies B.V. by Shandong New Beiyang Information Technology Co., Ltd. z Design and specifications are subject to change without notice. Ask your supplier for technical specifications before purchase and/or use. z Whenever in doubt about safety issues that might arise from using this product, please contact the supplier immediately for assistance.
BTP-R880NP Installation manual Declaration Information in this document is subject to change without notice. Shandong New Beiyang Information Technology Co., Ltd. (hereinafter referred to as “New Beiyang”) reserves the right to improve products as new technology, components, software, and firmware become available. If users need the further data about these products, please feel free to contact New Beiyang or your local agents.
BTP-R880NP Installation manual CONTENT GENERAL SAFETY INFORMATION ...................................... 2 1 INTRODUCTION OF BTP-R880NP ..................................... 3 2 PARTS IDENTIFICATIONS .................................................. 3 3 SETTING UP THE PRINTER ............................................... 4 3.1 UNPACKING....................................................................................... 4 3.2CONNECTING THE CABLES .......................................................
BTP-R880NP Installation manual General Safety Information Before installing and using the printer, please read the following items carefully. Safety Labels Don’t touch the cutter and tear bar of printer. The print head is a thermal element and it is at high temperature during printing or just after operation, therefore please do not touch it and its peripherals for safety reasons. The thermal head is an ESD-sensitive device. To prevent damage, do not touch either its printing part or connecting parts.
BTP-R880NP Installation manual 1 Introduction of BTP-R880NP BTP-R880NP is a high performance thermal printer, which can be widely used for real-time printing application, such as POS system, restaurant system, ATM, etc. BTP-R880NP can be connected with other devices via parallel interface, serial interface, USB, Ethernet or WIFI and is available for WINDOWS 2000/XP/Server 2003/VISTA/WIN7/ Server2008, Linux and MAC.
BTP-R880NP Installation manual Caution: The paper guides are indispensable parts of the printer and should be kept safely with the printer. 15— Paper-near-end sensor For continuous paper, this sensor is used to detect whether the paper roll has run out or near the end of the roll. 16— Printer platen 17— Power connector 18— Cash drawer connector 19— USB connector 20— Interface connector 3 Setting up the Printer 3.
BTP-R880NP Installation manual 3.2.1 Interface Connector RS-232 serial interface Pin Signal name Signal direction 1 FG — Frame ground 2 TXD Output Transmit data 3 RXD Input Receive data 4 RTS Output 6 DSR Input Function Same as DTR signal This signal indicates whether the host computer can receive data. SPACE indicates that the host computer can receive data, and MARK indicates that the host computer cannot receive data.
BTP-R880NP Installation manual transmits data after confirming this signal (except when transmitting data by DLE EOT, and GS a). When XON/XOFF control is selected, the printer does not check this signal. 7 SG — 20 DTR Output Signal ground 1) When DTR/DSR control is selected, this signal indicates whether the printer is busy. SPACE indicates that the printer is ready to receive data, and MARK indicates that the printer is busy.
BTP-R880NP Installation manual Ethernet Pin Number Signal Name Function 1 TX+ Output Data+ 2 TX- Output Data - 3 RX+ Input Data+ 4 NC 5 NC 6 RX- 7 NC 8 NC Input Data - USB interface Pin Number Signal Name Function 1 VBUS +5V 2 DATA- Printer data transmit line minus 3 DATA+ Printer data transmit line plus 4 GND Ground 3.2.
BTP-R880NP Installation manual 3.3Loading the Paper Roll Note: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. 1) Turn off the printer. 2) Open the printer top cover, as in the following figure. 3) Put the paper roll into the paper holder. See figure below. Note: Recommend paper Paper type Manufactory TF50KS-E2C,TF50KS-E Nippon Paper Industries Co.
BTP-R880NP Installation manual sensitive side will turn black. The paper on the roll should be tightly wrapped when loading the roll in the printer. The paper roll should be loaded straight in the printer and not slanted. In this way the roll will not be obstructed from rolling during printing. 4) Pull the end of the paper roll out up to the end of the top cover, and close the printer cover completely See figure below.
BTP-R880NP Installation manual If the auto cutter works in full cut mode, turn the wheel-knob counter-clockwise as shown in figure below (turn it inversely when partial cut) while observing its movement through the paper exit, do not stop turning until the moving blade is completely separated from the stationary blade. Then open the top cover to clear paper jam or such the like.
BTP-R880NP Installation manual 3.4.2 Remaining paper amount adjustment of Paper near end sensor Remaining paper amount can be adjusted by adjusting the position of paper near end sensor. The paper near end sensor has six levels and the red mark (actual color on printer is white) shows the current level and it can be adjusted to different position by moving the click wheel. 4 Switch, Button and LED 4.1 Power Switch The power button turns the power on or off.
BTP-R880NP Installation manual as long as the button is pressed. Print self-test page function When the FEED button is pressed while the printer is turned on, the printer will print out a self-test page. The page gives information about the printer and the settings. Before starting the self-test, make sure that a paper roll has been loaded and that the top cover is closed.
BTP-R880NP Installation manual Ending hexadecimal dumping function Hexadecimal dump mode can be ended by turning off the power, or by pressing the FEED button three times. 4.3 LED and Buzzers 4.3.1 LED LED Status Description Power Indicator (Green) On Printer is powered on (POWER) Off Printer is powered off Off Printer is in normal status Error Indicator (Red) (ERROR) Flash Printer is in error status or Paper near end 4.3.
BTP-R880NP Installation manual Font B: 0.25 mm {0.01"} (2 dots) Kanji: 0.125 mm {0.005"} (1 dot) Programmable by command 230 mm/s (Max) {9.05"/s} 54.3 LPS maximum (4.23 mm/feed) 7) Printing speed: 5.2 Auto Cutter Specifications Item Parameter Remarks Cutter type Slide cutter (Guillotine type) Cutting time 500ms The time that one cut takes. Cutting interval 3s 20 times/min. (Max.) Paper type Thickness: 0.06 – 0.1mm Operation voltage 24VDC Thermal paper or paper with the same thickness Max.
BTP-R880NP Installation manual 2) Storage temperature and humidity:-40~55℃,≤93%RH (40℃) 5.6 Reliability 1) Life times: Thermal head: Auto cutter: 2) MTBF: 3) MCBF: 100,000,000 pulses, 150 km 1,800,000 cuts 360,000 hours 60,000,000 lines 5.7 Black Mark Specifications The printer can print on thermal paper that has black marks on the reverse side of the heat sensitive side of the paper. The black marks are used for determining the top-of-form.
BTP-R880NP Installation manual 5.8 Overall Dimension 6 Wall Mounting The printer can be mounted vertically on the wall according to below instructions: 1) Drill two holes (OD: 6mm, depth: 50mm, space of two hole: 75mm) on the wall as in below figure: 2) Insert the plastic plugs in the holes and make sure that the plugs are fully inside the holes and do not stick out. 3) Screw the two screws in the plastic plugs and keep10mm space between the screw head and the wall surface.
BTP-R880NP Installation manual 4) Regulate the paper near end sensor (Please refer to 3.4.1), Mount the printer as figure. 7 Configuration setting function Parameter setting (configuring) by Feed button 1) Hold the FEED button pressed while switching the printer on. 2) After the printer has printed the configuration sheet, press and hold the FEED button to configure the printer. The main menu for the key-stroke setting procedure is printed.
BTP-R880NP Installation manual PARAMETER SETTING BY FEED BUTTON MAIN MENU Exit ->1 Print Self Test ->2 Configuration ->3 CONFIGURATION Exit Without Save ->1 Exit With Save ->2 Communication ->3 Back To Last ->1 Menu USB Interface ->2 USB MODE:API MODE Back To Last ->1 Menu Serial Interface ->3 WinDriver Mode ->2 API Mode ->3 SERIAL INTERFACE Back To Last ->1 Menu Baud Rates ->2 BAUD RATES:19200bps Back To Last Menu - 18 - ->1
BTP-R880NP Installation manual Parity 9600bps ->2 19200bps ->3 38400bps ->4 57600bps ->5 4800bps ->6 2400bps ->7 1200bps ->8 115200bps ->9 ->3 PARITY:NONE Back To Last Menu None Data Bits ->2 Odd ->3 Even ->4 ->4 DATA BITS : 8 Bits Back To Last Menu 7 Bits ->5 ->3 STOP BITS: 1 Bit Back To Last Menu 1 Bit - 19 - ->1 ->2 8 Bits Stop Bit(s) ->1 ->1 ->2
BTP-R880NP Installation manual 2 Bits Handshaking Data Receive ->6 ->7 ->3 HANDSHAKING:DTR/DSR Back To Last Menu ->1 DTR/DSR ->2 XON/XOFF ->3 DATA ERROR SETTING:Ignored Error Rx Buff Size ->4 RX BUFFER SIZE:4K Bytes Back To Last ->1 Menu 4k Bytes Mechanism & ->4 HARDWARE SETTINGS Hardware Back To Last Menu - 20 - ->1 ->2 45 Bytes ->3 64K Bytes ->4 Back To Last Menu ->1 Ignored ->2 Print '?' ->3
BTP-R880NP Installation manual Mark Sensor ->2 MARK SENSOR: Disable Back To Last ->1 Menu Cutter ->3 Enable ->2 Disable ->3 CUTTER: Enable Back To Last ->1 Menu Buzzer ->4 Enable ->2 Disable ->3 BUZZER: Normal Volume Back To Last ->1 Menu Low Volume Power Supply ->5 Normal Volume ->3 High Volume ->4 Higher Volume ->5 Highest Volume ->6 Disabled ->7 POWER SUPPLY: Normal - 21 - ->2
BTP-R880NP Installation manual Back To Last ->1 Menu Normal ->2 Low Power Mode Print Settings ->5 ->3 PRINT SETTINGS Back To Last ->1 Menu Darkness ->2 Settings DARKNESS SETTING: Normal Back To Last ->1 Menu Low Paper Roll Width ->3 ->2 Normal ->3 High ->4 Extra High ->5 PAPER ROLL WIDTH:80.0mm Back To Last ->1 Menu - 22 - 57.5mm ->2 69.5mm ->3 76.5mm ->4 80.
BTP-R880NP Installation manual 82.
BTP-R880NP Installation manual Code Page ->7 Enable ->2 Disable ->3 CODE PAGE SETTING Back To Last ->1 Menu Print all ->2 codepages Select a ->3 codepage Save Paper ->8 SAVE PAPER LEVEL Level Back To Last ->1 Menu Disable Two-color Mode ->9 ->2 25% ->3 50% ->4 75% ->5 100% ->6 TWO-COLOR SETTINGS Back To Last Menu - 24 - ->1
BTP-R880NP Installation manual Max Two-color ->2 Two-color Power:Normal Power Back To Last Menu High Power Proportion ->3 ->10 Gray Scale Mode:Mode3 Back To Last ->1 Menu Mode 0 - 25 - ->2 ->2 Normal ->3 Low ->4 Disable ->5 Power Proportion:50% Back To Last Menu Gray Scale Mode ->1 ->1 60% ->2 55% ->3 50% ->4 45% ->5 40% ->6 35% ->7 30% ->8
BTP-R880NP Installation manual Paper Sensor ->6 Mode 1 ->3 Mode 2 ->4 Mode 3 ->5 Mode 4 ->6 Mode 5 ->7 Mode 6 ->8 Mode 7 ->9 PAPER NEAR END Settings SETTINGS Back To Last ->1 Menu Paper Low Alarm ->2 PAPER LOW ALARM: Enable Back To Last ->1 Menu Stop Print When PAPER Low ->3 Enable ->2 Disable ->3 STOP PRINT WHEN PAPER LOW: Disable Back To Last ->1 Menu Enable - 26 - ->2
BTP-R880NP Installation manual Disable Paper Near End ->4 Sensor ->3 PAPER NEAR END SENSER: Enabled Back To Last ->1 Menu Set Default Config ->7 SET DEFAULT CONFIGURATION Back To Last ->1 Menu Set Printer To ->2 Default Configuration FONTA/FONTB ->8 Current Font:FONTA Settings Back To Last ->1 Menu Select FONTA ->2 Select FONTB ->3 Select UDFONTA ->4 Select ->5 - 27 - Enable ->2 Disable ->3
BTP-R880NP Installation manual UDFONTB Beep settings ->9 Beep settings:Disabled Back To Last ->1 Menu Enable External ->2 Herald Enable Internal ->3 BEEP MODE buzzer Back To Last ->1 Menu All Beep disabled Set Printer Mode ->10 ->4 Printer Mode:BTP-880NP Mode Back To Last ->1 Menu BTP-880NP - 28 - ->2 Mode 1 ->2 Mode 2 ->3 Mode 3 ->4 Mode 4 ->5 Mode 5 ->6
BTP-R880NP Installation manual Mode BTP-2002NP Mode Enter code,then hold Button Down at least 1 second to validate Cutter Test ->4 Sensor Test ->5 Sensor Test Mode: ERROR LED state will change according to sensor state To EXIT,hold button down at least 1 second Print Statistics ->6 Calibration ->7 E04 Configuration ->8 BTP-880NP STATISTICS TCUT :0 TLFS :0 ONTIME :0 E04CONFIGURATION Exit Without Save ->1 - 29 - ->3
BTP-R880NP Installation manual Exit With Save ->2 Saving config, please wait.