Owner's Manual
Table Of Contents
- Installation & Operation Manual
- Product Info
- SCM-MFD-LC-KIT & SCM-PD-RELAY-4 with SCR Underwater Lights & 4 Zones of RGB Lights
- SCM-MFD-LC-KIT & SCM-SNLC with 6 Switch Inputs, Shadow-NET® Lights & 5 Zones of RGB Lights
- SCM-MFD-LC-KIT with 2 Switch Inputs, Shadow-NET® Lights & 4 Zones of RGB Lights
- SCM-MFD-LC-KIT with 3 Switch Inputs, Shadow-NET® Lights & 4 Zones of RGB Lights
- SCM-MFD-LC-KIT with 6 Switch Inputs, Shadow-NET® Lights & 4 Zones of RGB Lights
- SCM-MFD-LC-KIT with Shadow-NET® Lights & 4 Zones of RGB Lights
SCM-MFD-LC-KIT
OPERATION MANUAL
Shadow-Caster
®
LED Lighting | 2060 Calumet Street. | Clearwater, FL 33765
p: 1+ 727.474.2877 e: info@shadow-caster.com w: shadow-caster.com
10
RECOMMENDED WIRE GAUGES
Scan the QR Code or click here to
view our recommended wire gauge
chart.
INSTALLATION
SCM-MZ-LC INSTALLATION
Central mounting locations under the helm areas or in
the bilges are acceptable.
1. Orient the cable glands facing down or to the side so
that they do not collect water.
2. Cinch cable glands as tightly as possible and ll
unused glands so that the box is water tight.
3. Use the included four 8 x ¾” SS pan head screws for
mounting.
SELECTING RGB OR RGBW LIGHTING
Set the RGB(W) dip switch within the SCM-MZ-LC,
depending on whether a zone is using RGB or RGBW
lighting, from left to right, as follows:.
Switch 1 2 3 4
ZONE 1
RGB
ZONE 2
RGB
ZONE 3
RGB
ZONE 4
RGB
ZONE 1
RGBW
ZONE 3
RGBW
ZONE 3
RGBW
ZONE 4
RGBW
SCM-ZC-REMOTE
and MFD
Connection
Zones 1-4
RGB(W)
Connections
12C DV
Power
Input
Shadow-NET
®
& 3.5mm Jack
(Music Sync)
Inputs
SCM-MFD-BRIDGE INSTALLATION
Central mounting locations under the helm areas or in
the bilges are acceptable.
1. Orient the cable glands facing down or to the side so
that they do not collect water.
2. Cinch cable glands as tightly as possible and ll
unused glands so that the box is water tight.
3. Use the included four 8 x ¾” SS pan head screws for
mounting.
SCM-MFD-BRIDGE CONNECTIONS
Ethernet Connection
Provides data connection to
Mult-Function Display (MFD)
SD Card Slot
The SD Card slot can
be used to store XYZ
Power (12V-30V) &
Shadow-NET
®
Connection
SCM-MFD-BRIDGE CONNECTIONS
SCM-MZ-LC POWER REQUIREMENTS
See the Shadow-Caster
®
wire awg recommendations
for detailed calculations. It is very important to have
sucient gauge wire feeds for RGB lighting.
It is recommended to separate feeds for lighting and
for sensitive stereo power feeds with direct runs to the
battery or a heavy gauge distribution point.
The SCM-MZ-LC will support 15 amps per zone. For
a total of 60 amps in the entire box. The SCM-MZ-LC
comes with 10 amp fuses installed.
The SCM-MZ-LC will work in 12V or 24V systems.
Please note that 12V or 24 compatible RGB(W)
products should be used depending on the application.