Installation manual

ManualsBrandsSG Security Communications ManualsMusical equipmentMLR2-E

Sixteen 4-digit passwords are available for use on the CPM2.

Password 0 is the Master Password, and Passwords 1 through

F may be assigned to individual operators. Two letters,

representing the initials of the operator, may be assigned to

each Password to help in identifying the operator.

When this option is entered, a cursor will appear beneath the

first character in the 4-digit Password. Enter a new Password

using the 0 through 9 and the A through F keys.

To enter the operator’s initials, used the [0] and [1] keys to

scroll forward or backward through the alphabet. When the

desired letter is displayed, press the [Enter] button - the

cursor will move to the next character. To move the cursor

to the previous character, press the [Backspace] button.

When the Password and initials have been entered, press

the [Escape] button - the next Password will be displayed.

When all Passwords have been programmed, the display

will advance to the next Configuration Option.

Option 03: Change the Number of Line Cards

Option [03] is used to set the number of Line Cards polled

by the CPM2. Press the [ACK] button when the “03: Numb

of Lcard” message is displayed. This message will be

displayed:

#LnCard Attached#LnCard Attached

#LnCard Attached

E Change to: xE Change to: x

E Change to: x

Enter a number from 1 to E to indicate how many Line

Cards, from 1 to 14, are to be polled by the CPM2. When

the new number is entered, press the [Enter], [Backspace],

or [Escape] button. The screen will then display the next

Configuration Option.

Option 04: Select Printer Function

Option [04] determines how the printer connected to the

CPM2 will operate. Press the [ACK] button when the “04:

PrinterSelect” message is displayed.This message will be

displayed:

Prter Config As:Prter Config As:

Prter Config As:

Bkup:0 Enable:1Bkup:0 Enable:1

Bkup:0 Enable:1

Enter a digit from 0 through 1 for both “Bkup” and “Enable”

according to the chart below:

BkupBkup

Bkup

Enable Enable

Enable

Printer OperationPrinter Operation

Printer Operation

0 0 Bypass printer

0 1 Enable printer (default setting)

1 0 Enable printer only if COM1 is in failure

1 1 Enable printer only if COM1 is in failure

(same as above)

If “Bkup” is programmed as “1”, messages will only be

sent to the printer if an acknowledge signal is not received

from COM1.

When using the Star 8340 printer, the CPM2 is able to print

in both red and black. If an IBM-compatible printer is selected,

the CPM2 will print in black only.

When programming is complete, press the [Escape] button.

When the [Escape] button is pressed, the next Configuration

Option will be displayed on the screen.

Option 05: COM1 Configuration

Option [05] determines the baud rate, data bits and parity

to be used on COM1. Press the [ACK] button when the

“05: Com#1 Config.” message is displayed. This message

will be displayed:

Com#1 Config As:Com#1 Config As:

Com#1 Config As:

Br:12 Da:7 Pa:2Br:12 Da:7 Pa:2

Br:12 Da:7 Pa:2

Br: Baud RateBr: Baud Rate

Br: Baud Rate

Enter...Enter...

Enter...

for baud ratefor baud rate

for baud rate

11 110

15 150

03 300

12 1200

24 2400

48 4800

96 9600

19 19200

38 38400

Da:Da:

Da:

Data Bits Data Bits

Data Bits

Enter a number from 7 through 9 to indicate

7, 8, or 9 data bits.

Pa: ParityPa: Parity

Pa: Parity

EnterEnter

Enter

for parityfor parity

for parity

0 no parity

1 odd parity

2 even parity

Note that the stop bit is fixed at 1.

When programming is complete, press the [Escape] button.

When the [Escape] button is pressed, the next Configuration

Option will be displayed on the screen.

Option 06: COM1 Communication Format

Option [06] determines the communication format to be

used on COM1. Press the [ACK] button when the “06: Com#1

Format” message is displayed. This message will be

displayed:

Com#1 Format is:Com#1 Format is:

Com#1 Format is:

1 Change to: x1 Change to: x

1 Change to: x

Enter a number from 0 to 5 to select one of the following:

0 COM1 disabled

1 Sur-Gard format (default setting)

2 Sur-Gard format with common event code "A"

3 Sur-Gard format with header 01 Hex.

4 Sur-Gard Clock Signal format

5 SIA CIS format

When option [06] is programmed as 5, the information to

the computer will be sent as follows:

When programming is complete, press the [Enter],

[Backspace], or [Escape] button. When a button is pressed,

the next Configuration Option will be displayed on the screen.

Option 07: Wait Time for Acknowledge on COM1

Option [07] determines the acknowledge wait time, in

seconds, to be used for COM1. Press the [ACK] button

when the “07: ACK Wait Time” message is displayed. This

message will be displayed:

<ACK> Wait Delay<ACK> Wait Delay

<ACK> Wait Delay

4.0S Chg to:x.xS4.0S Chg to:x.xS

4.0S Chg to:x.xS

Enter a decimal number from 4.0 to 9.9. Use the [Enter]

and [Backspace] buttons to move the cursor forward or

backward when editing the acknowledge time.

When programming is complete, press the [Escape] button.

When the [Escape] button is pressed, the next Configuration

Option will be displayed on the screen.

When the <ACK> wait time is programmed as “0.0”, the

CPM2 will not require a “06H” (ACK) from the computer.

Note: It is strongly recommended not to change the

default (4.0 sec.) unless recommended to by a Sur-Gard

representative technician.

Option 08: Heartbeat Time for COM1

Option [08] determines at what time interval, in seconds,

the supervisory “heartbeat” transmission will be sent to COM1.