Installation manual

ManualsBrandsSG Security Communications ManualsMusical equipmentMLR2-E

OUTEL Format

This is a 10 baud, single round, pulse format that consists

of a 2-digit account code and a one digit reporting code.

The print-out will be as follows:

L0X-ACC:AAssZnXssssssssssHH:MM:SS-DD/MM

Where L0X represents the receiving line card number

ACC:AA represents the 2-digit account number

s represents spaces

X represents the one digit reporting code

Robofon Format

The Robofon format is a 50 Baud pulse format sending

ASCII codes.

There is no English text library for the Robofon format,

therefore the printer output will look like:

L0X-ACC:AAAAAA YZ HH:MM:SS-DD/MM

Where: L0X represents the Line Card 0X

ACC:AAAAA represents the account AAAAAA

YZ represents the reporting code YZ

Scancom 433

This double round DTMF format uses 4-digit account codes

and up to 16 zones. The Scancom format requires either:

• a 1400 Hz handshake

• a Scantronics dual tone handshake

• a dual tone

• a 1600 Hz handshake

Scancom 433 examples:

Zone alarm reportsZone alarm reports

Zone alarm reports

If zone 3 is violated: 1234 013 003 FF

Zone status messageZone status message

Zone status message will indicate that the previously

reported violation is still present:

Zone 7 status: 1234 0EF 007 FF

Zone restoreZone restore

Zone restore

Zone 12 restore: 1234 034 012 FF

Zone test cancel:Zone test cancel:

Zone test cancel:

Zone 9 cancel: 1234 0BC 009 FF

Zone Bypass:Zone Bypass:

Zone Bypass:

Zone 7 bypassed: 1234 056 007 FF

Zone TroubleZone Trouble

Zone Trouble

Zone 2 trouble: `1234 078 002 FF

OpeningOpening

Opening

User 10 is closing Station 1 from keypad 3:

1234 996 010 FF

1234 001 003 FF

DuressDuress

Duress

User code 3: 1234 00F 003 FF

EmergencyEmergency

Emergency

Emergency 1: 1234 000 002 FF

Test report:Test report:

Test report: 1234 090 000 FF

Low battery:Low battery:

Low battery: 1234 098 000 FF

Printer OutputPrinter Output

Printer Output

For example, a panel sends in a zone 2 alarm.

First round: 1234012002FF

Second round: 1234012002FF

The printer output would be:

1234-02 Alarm

Scantronics Format

This DTMF format uses 2, 3, 4 or 6-digit account codes, 8

or 16 zones, and a 1-digit supervisory zone. The format

requires a dual tone handshake to send alarms, and a

1400Hz kissoff to complete the transmission. The following

table shows the zone events for this format:

Event codeEvent code

Event code

1 New event

2 Opening

3 Restoral

4 Closure

5 No event

6 Previous reported event still in effect.

7 No event on supervisory zone

8 Low Battery on supervisory zone

9 Test on supervisory zone

In order to receive the Scantronic format, the DRL2A should

be programmed using the F7 Command to send the Dual

tone handshake. The following are samples of transmissions

using this format:

Sample 1

The panel sends the following in 4-16-1 format:

123455555515111555558

This transmission will be decoded as follows:

PrinterPrinter

Printer

ComputerComputer

Computer

1234-800 LowBattery 1234 T 80

1234-107 AlarmZn#07 1234 A 07

1234-109 AlarmZn#09 1234 A 09

1234-110 AlarmZn#10 1234 A 10

1234-111 AlarmZn#11 1234 A 11

Sample 2

The panel sends the following in 6-8-1 format: First round:

987654515255537

The DRL2A decodes:

Printer Computer

987654-02 AlarmZn#02 987654 A 02

987654-04 Open-Usr04 987654 O 04

987654-08 RestrZn#08 987654 R 08

SIA FSK Format

The SIA digital format is a modem format communicating

at 110 or 300 baud and the SIA protocol to transfer information

to the computer.

The standard DRL2A is equipped with the Bell 103 modem

chip. The CCITT V.21 modem chip may be installed upon

request when ordering the MLR2-DG or DRL2A modules.

The CCITT V.21 chip is for use with modem frequencies

specified by the CCIT V.21 recommendation.

NOTE:NOTE:

NOTE: The DRL2A can accept SIA formats with and without

separators. The DRL2A Version 2.1i Software implements

Level 1, Level 2 and Level 3 of the 1993 IIb SIA Digital

Communication Standard, except that it does not support

"Receiver Call out and Access Passcode Block", "Reverse

Channel Block", and "V-Channel Communications".

To distinguish from the other formats already decoded by

the DRL2A, the data will be displayed on the printer as

follows:

L01-xx1234NBA-3423 18:36:00-30/09

• L01 represents Line Card 01

• xx1234 represents Account Code 001234

• N represents New event

• BA represents a Burglary Alarm

• 3423 represents Zone 3423

• 18:36:00 is the time in the 24-hour clock format

(hours:minutes:seconds; in this example, the time is 6:36

pm)

• 30-09 represents the date; in this example, the date is

September 30