Installation manual

ManualsBrandsSG Security Communications ManualsMusical equipmentMLR2-E

DRL2A PROGRAMMING COMMANDS

• Enter the Option number. In this example, Option [36] will

be changed. When “36” is keyed in, the Option will appear

on the display as shown below:

LCard:01 Comd:F7LCard:01 Comd:F7

LCard:01 Comd:F7

Op:36 Cd:__ Sc:__Op:36 Cd:__ Sc:__

Op:36 Cd:__ Sc:__

• Enter the value to be programmed at Option 36. In this

example, 01 will be programmed at Option [36] to enable

it. When “01” is keyed in, the value will appear on the

display as shown below:

LCard:01 Comd:F7LCard:01 Comd:F7

LCard:01 Comd:F7

Op:36 Cd:01 Sc:__Op:36 Cd:01 Sc:__

Op:36 Cd:01 Sc:__

Note that “Sc” is not used and stays blank. After the

value is entered at “Cd:”, press [ACK] or [Escape] to

save the changes.

NOTE: NOTE:

NOTE: If the [Escape] button is

pressed before the value at “Cd:” is entered, the

changes will not be saved.

Verifying Data

• To verify the changes just entered, press and hold the

[ACK] button on the DRL2A until this message is displayed:

Dsp CONFIG syst.Dsp CONFIG syst.

Dsp CONFIG syst.

ACK:menu SEL:selACK:menu SEL:sel

ACK:menu SEL:sel

• Press the [SELECT] button to view the system configuration.

This message will be displayed:

L01 #00L01 #00

L01 #00

0000

4/1 DIGIT#0 -A-4/1 DIGIT#0 -A-

4/1 DIGIT#0 -A-

Press the [ACK] button to scroll forward through the

configuration displays until you reach option 36, or press

the [SELECT] button to scroll backwards through the

configuration displays. Press [ACK] and [SELECT] together

to return to the Stand-By Mode.

1.0 Line Card Options Programming:

LC-F7-OP-CD

The F7 Options Programming command is used to change

various operating parameters for the Line Card. (Reporting

Codes, the Line Card number, buzzer operation and other

features). Also functions may be changed using the F7

command.

Refer to the example illustrated in “Entering Commands” in

the “DRL2A Programming Commands” section of this manual.

Refer to the DRL2A Reference Sheets in the back of this

manual. Be sure to record any programming changes on

these sheets.

NOTES:NOTES:

NOTES:

Options are programmed with 2 hexadecimal or

decimal digits (depending on the option), but are shown

on the DRL2A screen with 3 digits. This allows 3-digit decimal

display for some options.

Options [00] through [30], and [4D] are programmed

with ASCII codes (refer to Appendix F for ASCII code

information).

Options [00] - [0F]: 3/1, 4/1 Format Event Codes

and printer library selection

The DRL2A uses a unique Sur-Gard communication format

to transmit data through the CPM2 to the central station

computer. Event codes corresponding to alarm codes in

10 to 40 BD formats and DTMF 4/1 to 4/3 formats are used

in this unique format to enable the computer software to

determine alarm types.

There are 5 main Programming Commands available on the

DRL2A Line Card Module:

• F7 Options Programming

• FA Buffer Output

• FB Shutdown Line Card Communications with CPM2

• FC Reactivate Line Card Communication with CPM2

• FE Line Card Buffer Maintenance

Some Programming Commands have options, each with a

variety of functions. Each command is fully explained in

the following sections of this manual.

Entering Commands

Commands are entered on the CPM2 keypad using the

following format:

LCard; Comd; OP; CD; SC

• LCard: “Line Card” is the Line Card number. Enter a

hexadecimal number from 01 to 0E for Line Cards 1

through 14

• Comd: “Command” is the Command. Enter a command

from the list above

• OP: “Option” indicates a function that is part of a command.

The following sections of this manual will explain which

commands have options. Enter a 2-digit hexadecimal

number

• CD: “Code” is the code or value to be programmed for

the Option. Enter a 2-digit hexadecimal number

• SC: “Second Code” is a code or value that is only used with

SCADA commands. If required, enter a 2-digit hex number

Example:

The following is how to enter the Programming Password

and program an Option in the F7 Options Programming

section:

Entering Data

• Press and hold the [C] button on the CPM2 until the

CPM2 displays the following message:

Enter PASS-WORDEnter PASS-WORD

Enter PASS-WORD

****

The default password is “CAFE”. Enter the password

using the CPM2 keypad.

• When the password is entered, the CPM2 will display

this message:

LCard:__ Comd:__LCard:__ Comd:__

LCard:__ Comd:__

Op:__ Cd:__ Sc:__Op:__ Cd:__ Sc:__

Op:__ Cd:__ Sc:__

• Enter the Line Card number. In this example, Line Card

01 will be used. When “01” is keyed in, the number will

appear on the display as shown below:

LCard:01 Comd:__LCard:01 Comd:__

LCard:01 Comd:__

Op:__Op:__

Op:__

Cd:__Cd:__

Cd:__

Sc:__Sc:__

Sc:__

• Enter the Command number. In this example, the F7

Options Programming command will be used. When “F7”

is keyed in, the command will appear on the display as

shown below:

LCard:01 Comd:F7LCard:01 Comd:F7

LCard:01 Comd:F7

Op:__Op:__

Op:__

Cd:__Cd:__

Cd:__

Sc:__Sc:__

Sc:__