Ve So ftw w fo r Nege 1 Se e e s a r ature w Ne i rs o n ang e d an s Ch Fe Pa Installation Manual MLR2-DG Version 2.
Important Information Relating to the Connection of this Equipment to the Telephone Network 1 This equipment is approved for connection to the Public Switched Telephone Network (PSTN) via direct exchange lines offering LD (pulse) or MF (tone) dialling facilities. 2 This equipment has a ringer equivalence number (REN) of 3.0. The REN indicates how many telephone or other types of equipment may be connected to your telephone line simultaneously.
TABLE OF CONTENTS INTRODUCTION 1 CPM2 ..................................................................................... 1 DRL2A ................................................................................... 1 Power and Supervision .......................................................... 1 Compatibility .......................................................................... 1 CPM2 Outputs ....................................................................... 1 NEW FEATURES ....................
3.0 Shutdown Line Card Communication with CPM2: LC-FB ............................................................... 4.0: Reactivate Line Card Command: LC-FC ...................... 5.0: Line Card Buffer Command: LC-FE-XX-XX .................. 5.1 Erase Alarm Printer/Computer Messages: LC-FE-00-00 ................................................................... 5.2 Software Reset: LC-FE-02-02 .................................. 5.3 Backup Current Line Card Configuration: LC-FE-03-03 ......................
INTRODUCTION The MLR2-DG is a Multi-Line, Multi-Format Digital Receiver, Listed U.L. and U.L.C. for commercial fire and burglary. The basic unit consists of a CPM2 Central Processor Module and a two DRL2A Digital Receiver Line Card Module. Additional DRL2A Line Cards may be added to enable the CPM2 to monitor up to 14 telephone lines. The MLR2-DG includes many features, all designed to make the receiver more powerful and easier to use.
SYSTEM OVERVIEW • Caller Identification (Call Display) capability • Non-Volatile RAM on each DRL2A line card module for programming and event buffer • 3/1, 4/2 formats with or without parity, 4/1 without parity at 10, 14, 20, or 40 baud • 4/1, 4/2, 4/3, and 4/3 DTMF formats. • Optional* Formats: 3-2, 4/1/4/2 extended.
QUICK START Receiver Setup and Operation Without Programming Unpacking Carefully unpack the receiver and inspect for shipping damage. If there is any apparent damage, notify the carrier immediately.
INSTALLATION Mounting the Receiver • Install the MLR2-DG in a closed 19" rack or cabinet with a locking rear access door. Cover all unused spaces with blank metal plates. The LCD screens on the receiver are designed to be viewed below eye level. If the unit must be mounted where the screens are above eye level, angle the unit downwards to improve visibility.
System power supply rated 12VDC. Connect the positive lead from the DC supply to the BLGT terminal; connect the negative lead from the DC supply to the GND terminal. CAUTION: Connecting a positive (+) terminal to a negative (-) terminal may cause a fire and possibly serious personal harm. • For 24 hour stand-by, 12V 17.5Ah rechargeable battery should be used for 6 lines configuration, and 12V 38Ah rechargeable battery should be used for 14 lines configuration.
AC IN AC OUT 16VAC power input 16VAC filtered power output HNDSET A Not used Fused 12V output AUX BATT 12V battery RCA Not Used B.
MLR2-DG BACKPLANE CONNECTION DIAGRAM 7
MLR2-DG INSTALLATION Connections for DML2A Line Card Expansion 8
DRL2A DIGITAL RECEIVER LINE CARD The DRL2A acts as an interface between the digital alarm transmitter and the CPM2. Different communication formats can be used to transmit the information. The main functions of the line cards are to continuously monitor the telephone line, receive calls from digital dialers or control panels, and to report alarms to the CPM2.
Installation It is recommended that a DRL2A Cold Start-up be performed when the unit is updated with a new program version. Refer to Operating Mode Section 3.0 (DRL2A Cold Start-up and Changing The Line Card Number) for information. After the cold start-up, check the configuration information listed in the Quick Reference Guide to make any required changes for your particular application. DRL2A Controls Each DRL2A Module features 2 line cards.
DRL2A OPERATING MODE 1.0 DRL2A Stand-By Mode With the Line Card installed, apply power to the unit. This message will be displayed on the LCD screen for 1 second: JUNE 04,97 V 2.1i The following messages are sent to the printer and computer: Printer: L0x???????Dx LCardReset Computer: 0000 A Dx A hexadecimal digit from 1 to E representing the number of the Line Card will be sent for each “x” shown above.
2.1 Display Printer and Caller ID Alarm Buffer Dsp PRINTER alm ACK:menu SEL:sel With this message displayed, press the [SELECT] button. The most recent alarm message will be displayed. Press the [SELECT] button to scroll backwards through alarm messages; press the [ACK] button to scroll forward through alarm messages. L01-3576-312 Alarm 001 • “L01” represents Line Card 01 • “3576” is the Account Code • In this example, a 4/3 communication format is used.
4.0 Communications in Progress 4.1 Data Reception During data reception, a message similar to this will be displayed: In Communication 1234 56 The DRL2A decodes all information received and stores the information in its Event Buffer. When a valid signal is received, the DRL2A sends a kissoff signal and transmits the decoded alarm signal to the computer and then to the printer through the CPM2. voice communication over the same telephone line after digital data has been received.
Audio Mode Operation Alarm Zone Method When in Audio Mode, the “Audio” light will be ON and this message will be displayed: After the digital alarm data has been received and the receiver has transmitted the last kiss off, the receiver compares the alarm zone codes received in 3/1, 4/1, 4/2, 4/3, 10-40 BD or DTMF touch-tone formats to the value programmed in option [50]. The alarm zone code is the last digit for all formats. This is done to determine if the 2Way Audio Mode should be activated.
DRL2A PROGRAMMING COMMANDS There are 5 main Programming Commands available on the DRL2A Line Card Module: • F7 Options Programming • FA Buffer Output • FB Shutdown Line Card Communications with CPM2 • FC Reactivate Line Card Communication with CPM2 • FE Line Card Buffer Maintenance Some Programming Commands have options, each with a variety of functions. Each command is fully explained in the following sections of this manual.
The DRL2A will use the last digit of data received in 3/1 and 4/1 formats to determine the printer message and computer event code. The event code will then be transmitted to the central station computer. Refer to the DRL2A Decoding Library for the complete set of messages and event codes used by the DRL2A. In Sections [00] through [0F], program ASCII codes according to the Decoding Library. Values other than 20-7F (ASCII ) will not be accepted.
Value 00 01 Ex: 02 Ex: 03 Ex: Function Option [37]: Send Caller ID to Computer No communication to computer Alarms communicated to computer. If the alarm is reported in 3/1, 3/1 extended, 3/2 or 3/8 ACRON formats,a leading space will be communicated in front of the 3-digit Account Codes when sent to the computer s AAAsXsssY[DC4] 1011sssssss The DRL2A can send the caller identification numbers to the computer.
Option [3F]: Last Message On of this time, the Line Card will hang up the line. When Option [3F] is enabled, the last alarm message will be retained on the Line Card display screen until a new signal is received. Program Option [3F] as “01” to enable this feature, or as “00” to disable it. If Option [3F] is disabled, the stand-by message described in Section 1.4 will be displayed when communication of an event is completed. Program a value from “01” to “99” for 1 to 99 minutes.
Option [4D]: Audio Event Code Option [4D] is used to send a message to the computer and the printer to indicate that the Line Card has enabled the 2-Way Audio function. Program an ASCII code using 0 through 9 and A through Z to be used as the event code for activation of the 2-Way Audio feature.
Printer: 1234-B01 CloseGrp 1234-416 Close 1234-C02 OpenGrp 1234-532 Open Computer: 1234 C1 16 (instead of 1234 C 01 and 1234 C 16) 1234 O2 32 (instead of 1234 O 02 and 1234 O 32) Option [58] = 01; equivalent line number is 1 If receiver number is 02 and the line number is 3: the printer message will be “L21-1234...” and the computer message 021 will be: 1021 021ssssss1234 If a user code is not received after the group opening/ closing, the message “1234 C1 FF” will be sent.
00 01 1RRLsssssss234sCsC2[DC4] 1RRLsssssss234sCss2[DC4] a hexadecimal number from 01 to FE to indicate a number of events from 1 to 255. Where RR = Receiver Number L = Line Number s = Space [DC4] = Terminator Please note that option [30] must be left as individual event code when enabling this option. Option [60]: ScanCom 4332 When programmed as “01”, the receiver will transmit the Scancom 433 as received. Please refer to the computer protocols section on page 36 for more details.
5.3 Backup Current Line Card Configuration: LCFE-03-03 When the Line Card has been configured, the programming changes can be recorded as a “back up” program. The “back up” configuration may be later used to restore the Line Card’s configuration after temporary changes are made. To store the present Line Card configuration, enter the LCFE-03-03 command. 5.
• L01 indicates Line Card 01 • 1234 is the Account Code • E indicates an opening • 130 is the event code • 01 indicates Group 01, 025 indicates Zone 25 Refer to "Communication protocol with central station computer". the previous 8 channels Printer: 1234-B1 TrbleZn#01 Computer: 1234 T B1 6 Ademco Express Format This format consists of 4-digit Account Codes and 1- or 2digit alarm codes. The DRL2A will decode the signal as regular 4/1 or 4/2 format.
FBI Super Fast Format This DTMF format consists of 4-digit Account Codes, 2-digit zone codes, 1-digit zone type codes, and 1-digit event codes. The zone codes will be converted into 3-digit decimal codes by the DRL2A.
OUTEL Format Event code This is a 10 baud, single round, pulse format that consists of a 2-digit account code and a one digit reporting code. 1 2 3 4 5 6 7 8 9 The print-out will be as follows: L0X-ACC:AAssZnXssssssssssHH:MM:SS-DD/MM Where L0X represents the receiving line card number ACC:AA represents the 2-digit account number s represents spaces X represents the one digit reporting code Robofon Format The Robofon format is a 50 Baud pulse format sending ASCII codes.
The DRL2A supports a maximum of 16 digits account code, (including any displayable ASCII characters except the "|") with option 31 (SIA option for Level 2 & 3 decoding) enabled (01), up to 6 digits account code with option 31 disable(00). If option 31 (SIA level 2-3) is disabled, the "A"s received in the account code will be converted to "0"s. It also supports a maximum of 4 digits for the Alarm Code. Usually, the central station automation software will interpret the Alarm Codes.
MODULE The CPM2 is the central processing module that monitors the DRL2A Line Cards and forwards the information from the Line Cards to the computer and printer. The CPM2 is capable of monitoring a maximum of 14 telephone lines from 7 DRL2A modules. General Information The CPM2 16-bit micro-controller and real-time assembly language program running at 16MHz allow the system to quickly and efficiently execute several tasks at the same time.
CPM2 OPERATING MODE CPM2 Cold Start-up The “cold boot” should be performed to install the default system software. Follow the procedure described here to perform a “cold boot” of the CPM2. • Remove the CPM2 from the card cage • Turn the “PROG EN” (Program Enable) switch ON. The Program Enable switch is located on the left side of the CPM2 unit. Use a small screwdriver to turn the switch ON. • Re-install the CPM2 in the card cage, but do not fasten the mounting screws.
Sixteen 4-digit passwords are available for use on the CPM2. Password 0 is the Master Password, and Passwords 1 through F may be assigned to individual operators. Two letters, representing the initials of the operator, may be assigned to each Password to help in identifying the operator. When this option is entered, a cursor will appear beneath the first character in the 4-digit Password. Enter a new Password using the 0 through 9 and the A through F keys.
The “heartbeat” transmission is used to ensure that communications through COM1 are functioning normally. Press the [ACK] button when the “08: Heartbeat Sel” message is displayed. This message will be displayed: Heartbeat Select 30S Chg to:XXSec Enter a decimal number from 01 through 99 to determine the time interval between heartbeat transmissions. Program this option as “00” to disable the heartbeat transmission.
When programmed as “0”, the buzzer will sound when an alarm is received and cannot be forwarded to COM1. The default setting is “0”. NOTE: Option 14 will have no effect on the buzzer if the UL Receiver Option is enabled. Option 15: Display Last Message When an alarm is received, the alarm message will be displayed on the screen until the message is forwarded to the computer and printer. When the message is sent to the computer and printer, the Stand-By Mode message will be displayed.
Program Option [21] as “1” to include the year in the alarm message date. Alarm messages will be printed as follows: L01-1234-05 Alarm 21:24-24/11/94 Note that the time (21:24) is represented with just hours and minutes, and that the year is added to the date (24/11/ 94). Program Option [21] as “0” to include the seconds in the alarm message time. Alarm messages will be printed as follows: L01-1234-05 Alarm 21:24:30-24/11 Note that the time (21:24:30) now includes hours, minutes and seconds.
*Feb-23 07:30:45 Width" is displayed. The following message will then be displayed: 40/80 Column: 0 Change to: 0/1 Press "1" and then [Enter] to enable the 80-column width feature. Option 28: Tamper Input To view the Tamper Input / UPS Low Battery supervisory, press the [ACK] button until "28: Tamper Input" is displayed.
When the CPM2 is in the Stand-By Mode, the following functions may be accessed by pressing the [A] through [F] keys: • • • • • • [A] Send Computer Messages to Printer [B] Operator Log-On [C] System Command Mode [D] Send Printer Messages to the Printer [E] Examine Printer Messages on Display Screen [F] Examine Computer Messages on Display Screen [A] Send Computer Messages to Printer This mode is used to send the computer messages from the buffer to the printer.
displayed: L01-1234-05 Alarm xx • xx indicates the number (in hexadecimal) of printer messages in the Line Card buffer. Press the [Enter] button to scroll through the messages. The messages will be displayed in order from the most recent to the oldest. Press the [Backspace] button to scroll from the oldest message to the most recent. When finished viewing the messages, press the [Escape] button.
The Sur-Gard MLR2-DG receiver sends the following to report STATION signals to the central station computer via the RS-232 COMMUNICATION PROTOCOL WITHprotocol CENTRAL COMPUTER port. Data Byte Protocol: signal when necessary. The Sur-Gard receiver uses 1200 baud rate, 1 start bit, 7 data bits, 1 even parity bit, and 1 stop bit structure, to transmit and receive signals. The above protocol can be programmed on the receiver by the central station operator to enable different configurations.
2 as the following: (option [31] enable) SRRL[#AAAAAA|EMMZZZZ/MMZZZZ/MMZZZZ][DC4] Where, S : Beginning transmission of the new SIA protocol RR : Receiver number 00-FE L : Line number 0-E [ : Beginning data delimiter # : Account ID block code AAAAAA : Account ID, maximum sixteen digits.
RR L AAAAA X When: ZZ [DC4] s : receiver number : line number : account number (5 digits) : alarm type X=1 : Alarm X=2 : Restore X=3 : Status: Alarm X=4 : Status: Normal : zone number : represents the terminator : represents spaces RR L AAAA s CCCC s CCCC s C [DC4] 1RRLssssssss00AAsEss0Z[DC4] 5RRLs18AAAAQXYZGGCCC[DC4] 5 RR L s 18 AAAA Q XYZ GG CCC [DC4] : : : : : : : : : : : Protocol number. Receiver number. Line number. Space. Contact-ID format identifier. Four digit account codes.
10-35 36-61 62 and greater “A” - “Z” “a” - “z” “?” RR : receiver number L : Line number s : spaces AAAA : Account code. T : Zone type ZZ : Zone number, in hex. E : Event code if E=0 and T=0 : listen in. NOTE: The DRL2A will not respond to any interactive commands from the ITI panels. The audio feature is supported for ITI accounts.
3 4 5 6 7 8 FF T 013 014 015 016 017 018 11 023 12 024 13 025 14 026 15 027 16 028 : format terminator : terminator character British Caller ID Protocol URRLAAAAAATTTTTTTTTTTTTTTTTT[DC4] Where: U is International caller ID protocol identifier RR is the receiver number L is the line number AAAAAA is the account number (leading spaces or leading zeros if account is less than 6 digits) TTT...
SPECIAL APPLICATIONS SUR-GARD NETWORK (SCADA) A complete package to allow one or more receivers in distant cities to communicate their alarm information to a master receiver and to be remotely controlled by the master receiver. The acronym "SCADA" stands for Supervisory Control And Data Acquisition. It is used to transport the alarm data from a local (satellite) central station to the master central station reliably by using linked Modem over leased phone lines.
MLR2-DG RECEIVER PROGRAMMING SOFTWARE Introduction: The MLR2-DG can be programmed through the serial port #2 on the CPM2 from a computer, with the DOS-based MLR2DG programming software. This method of programming is more user friendly, faster and each installation configuration can then be saved on disk. For more information or ordering, please contact your distributor.
UPS CONNECTION 220 Vac/16Vac, 50Hz, 175VA Transformer 220 Vac 50Hz 43
MLRV-A AUTOMATED VIDEO RECEIVER MODULE The Automated MLRV-A Video Receiver Module provides for the receiving of video images over the regular telephone lines following the Event information. One MLRV-A module connects to and works with one Digital Receiver line (DRL2A). The MLRV-A can only connect to and work with the Sur-Gard MLR2 Multi Line Receiver.
PSA V1.00 SOFTWARE Downlook PSA software allows for video images to be displayed, saved, retrieved, printed and managed on a standard PC. A 486 or Pentium with a least 8 Meg of ram must be used, it is advised other than DOS, Windows 3.11 or Windows 95 no other program should run with the Downlook PSA as a conflict of software could exist. All functions on the software can be accessed by the use of a mouse or by a touch screen monitor.
APPENDIX A DRL2A QUICK REFERENCE GUIDE Version 2.
APPENDIX B CPM2 QUICK REFERENCE GUIDE Version 2.1 CPM2 Utility Modes Press [ACK] when “Ack” light flashes to Acknowledge event • [A] Send Computer Messages to Printer • [B] Operator Log-On • [C]System Command Mode • [D]Send Printer Messages to the Printer • [E] Examine Printer Messages on Display Screen • [F] Examine Computer Messages on Display Screen CPM2 Configuration Mode Press the [Escape] button when the system is in Stand-By Mode and enter the Master Password.
APPENDIX C TROUBLE SHOOTING Problem: No communication with the central station computer on COM1 Solution: Ensure that the cable connected to COM1 is an RS232 cable; it should not be a null-modem type. Check the baud rate for COM1 (CPM2 Configuration Option 05) Check the COM1 communication format (CPM2 Configuration Option 06) Check the computer software set-up Enable COM1 Diagnostics with CPM2 Configuration Option 16 and examine the communications on the display screen.
APPENDIX D DRL2A COMMUNICATION FORMATS (2.
APPENDIX E DECIMAL - HEX - BINARY CONVERSION CHART DEC 000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 50 HEX 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F
APPENDIX F ASCII CHARACTER CHART ASCII with library on printer (Option 30) Hex Corresponding ASCII Character 20 Space B0 30 0 B1 31 1 B2 32 2 B3 33 3 B4 34 4 B5 35 5 B6 36 6 B7 37 7 B8 38 8 B9 39 9 C1 41 A C2 42 B C3 43 C C4 44 D C5 45 E C6 46 F C7 47 G C8 48 H C9 49 I CA 4A J CB 4B K CC 4C L CD 4D M CE 4E N CF 4F O D0 50 P D1 51 Q D2 52 R D3 53 S D4 54 T D5 55 U D6 56 V D7 57 W D8 58 X D9 59 Y DA
APPROVED for connection to telecommunication systems specified in the instructions for use subject to the conditions set out in them. BABT/503546 SG-MLR2-DG © 1997 Sur-Gard Security Systems Ltd. 401 Magnetic Drive, Unit #24, Downsview, Ontario, Canada M3J 3H9 REN = 3.
