Sur-Gard MLR2E Multi-Line Digital Receiver Installation and Operation Manual WARNING: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer. The entire manual should be carefully read. version 1.
Table of Contents Section 1 - Introduction .................................................. 1 1.1 CPM2 ................................................................. 1 1.2 DRL2E ................................................................ 1 1.3 Supervision ......................................................... 1 1.4 CPM2 Outputs/Inputs ......................................... 1 1.5 System Overview ................................................ 1 1.6 Virtual Receiver Architecture .............
FCC Compliance Statement CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use this equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Section 1 - Introduction 1.4 The MLR2E is a multi-line, multi-format digital receiver for commercial fire and burglary. The basic unit consists of up to 15 individual line card modules (DRL2E) and 30 telco lines connected to a CPM2. The MLR2E can decode a variety of popular and widely used communication formats. Refer to Appendix A, DRL2E Communication Formats for a list of the available communication protocols.
1.7 • Switched-negative outputs on CPM2 (special applications) • AC-lost detection and standby battery supervision • Low battery detection and automatic low battery disconnect to prevent deep-discharge damage to battery • Operator Acknowledge option • Telephone line supervision and reporting 1.6 Number of Line Cards Supported The system will support a maximum of 15 line card modules concurrently connected. 1.8 Approvals 1.8.
Figure 1, MLR2E Backplane Connection P5 R13 R11 R4 R7 R12 R6 P6 MV3 MV2 P4 For 120VAC Mains Battery 12V Rechargeable lead-acid 35Ah For Model SG-MLR2E CE* Transformer 16 VAC, 175 VA 120VAC 60Hz * Model MLR2E CE is not UL approved.
Figure 3, MLR2E UL UPS Connection, 120 VAC Mains 120 VAC/16 VAC, 60 Hz, 175 VA TRANSFORMER 120 VAC 60Hz NOT USED P5 R13 R11 R4 R7 R12 R6 P6 MV3 MV2 AUX CONSOLE/DEBUG P4 Battery 12V Rechargeable lead-acid 35Ah Transformer 16 VAC, 175 VA 120 VAC 60Hz 4 P2
Figure 4, Model MLR2E CE UPS Connection, 240 VAC Mains* 240 VAC/16 VAC, 50 Hz, 175 VA TRANSFORMER 240 VAC 50 HZ 12 V Battery (Supervised) NOT USED P5 R13 R11 R4 R7 R12 R6 P6 MV3 MV2 AUX CONSOLE/DEBUG P4 Battery 12V Rechargeable lead-acid 35Ah GROUND CONNECTION Tighten nut to break paint and make a good connection to the cabinet Nut Lock washer Transformer 16 VAC, 175 VA 240 VAC 50 Hz Ground wire from building electrical installation Nut Lock washer Star washer Cabinet Bolt * Not to be used i
Section 2 - Quick Start 2.1 Receiver Setup and Operation without Programming 5 6 7 8 2.1.1 Unpacking Carefully unpack the receiver and inspect for shipping damage. If there is any apparent damage, notify the carrier immediately. 7 6 4 5 7 20 5 4 5 4 8 7 Ground - Ground DSR - DTR RTS - CTS CTS - RTS Figure 5, Seral Laplink Cable (on cable) 2.1.
Section 3 - Installation 3.1 Mounting the Receiver 3.2 Install the MLR2E in a closed 19" / 48cm rack or cabinet with a locking rear access door. Cover all unused spaces with blank metal plates. The LCD screens on the receiver are designed to be viewed below eye level. If the unit must be mounted where the screens are above eye level, angle the unit downwards to improve visibility.
Section 4 - DRL2E Digital Receiver Line Card The DRL2E acts as an interface between the digital alarm 4.3 transmitter and the CPM2. Different communication formats can be used to transmit the information. The main functions of the line cards are to continuously monitor the telephone line, receive calls from digital dialers or control panels, and to report alarms to the CPM2. In addition, each line is capable of functioning independently when communication is lost between the line card and the CPM2.
Section 5 - DRL2E Operating Mode 5.1 DRL2E Standby Mode Up to 128 alarm messages for the printer and computer will be retained in the CPM2 event buffer. When the event buffer is full, the oldest messages will be deleted as new events are recorded. When the CPM2 error condition is corrected, the alarm messages in the event buffer will be transmitted to the CPM2. When the line card is operating normally, this message will be displayed: DRL2E–Line #D Unit in Standby 5.1.
5.1.9 Adjust Backlight ADJUST BACKLIGHT ACK: up SEL: down If no Caller Identification data was received from the telephone company, the following message will be displayed when the [ACK] button is pressed to display the Caller Identification screen: The [ACK] button is used to brighten the backlighting and the [SELECT] button is used to darken it. 1234 — UnknownCall 5.
5.3 Communications in Progress 5.3.3 Communication Fail When this problem is encountered, the following information is transmitted to the printer and the computer: Printer: L01-0000-COMMUNICATION FAIL TIME: DATE Computer: 0RRL[#0000 | NYCRRL] NOTE: The first RRL is subject to the line card length option. The second RRLL is the receiver and line card number, both in HEX. This output indicates that a call was received, but no data was detected.
Section 6 - Profiles 6.1 Introduction By receiving the DNIS or Caller ID, the appropriate profile can be selected through a look-up table "stored" on the line card. The DRL2E 'virtual receiver' will load unique 'profiles' in order to effectively communicate with control panels. A profile is a set of pre-programmed line card options unique for a particular DNIS number. The 'DNIS' will point to a particular profile, which will then be loaded into the line card before the first handshake is sent.
Entering Data • Press and hold the [C] button on the CPM2 until the CPM2 displays the following message: Table type 2: Entry Number 0001 0002 0003 Caller ID Received 14166654492 1938271623 8005764646 Represent 1-416-665-4492 Profile# to be used 01 03 24 Enter PASS-WORD **** The default password is 'CAFE'. Enter the password using the CPM2 keypad. • When the password is entered, the CPM2 will display this message: The receiver will check through the Caller ID section if a Caller ID number is received.
6.2.1 F7 Line Card options Programming Option [04]: 2-Way Audio Activation Time - Default [00]* Line Card-F7-Option-Code The F7 Options Programming command is used to change various operating parameters for the line card: reporting codes, the line card number, buzzer operation and other features. Functions can also be changed using the F7 command. Refer to the example illustrated in 'Entering Commands' in the 'DRL2E Programming Commands' section of this manual.
Computer: 1234 C1 16 (instead of 1234 C 01 and 1234 C 16) 1234 O2 32 (instead of 1234 O 02 and 1234 O 32) If a user code is not received after the group opening/ closing, the message “1234 C1 FF” will be sent; “FF” indicates that a user code was not received. The second nibble of this option controls the user/zone number conversion. The Sur-Gard 4/3 DTMF format is made up of a 4-digit account code, a 1-digit event code, and a 2-digit hexadecimal zone code or user number.
6.4 Option [1C]: Busy Out - Default [00] Dynamic Options: [30] - [FF] Options [30] - [3F]: 3/1 - 4/1 Digit 0-F This option allows the line card to seize the phone line in case of checksum error after download or when its internal buffer is full after loss of communication with the CPM. Program Option [1C] with one of the following: 00 The line is seized if any of the conditions mentioned above occurs. 01 The line is NOT seized if any of the conditions mentioned above occurs.
Option [70]: Automation Common Event Code Default [00] Options [50] - [5F]: 4/3 Digit 0-F The DRL2E will use the fifth digit of data received in 4/3 formats to determine the message and event code. The event code will then be transmitted to the central station computer. Refer to the DRL2E Decoding Library for the complete set of messages and event codes used by the DRL2E. In Sections [50] through [5F], program ASCII codes according to the Decoding Library. Do NOT use values other than 207F (ASCII).
The receiver will do the following. First it will replace the first digit (Option A2=01) of the account code (in this example "1") and replace it with the ASCII value of 41, which is an "A". New Output: Option [74]: Equivalent Line Number - Default [00] The equivalent line number is used with the receiver number for sending signals to the central station software.
To disable the 2-way audio function, program Option [7A] as '00'. NOTE: Option [7A] may be used with any formats supported by the MLR2E. *Option [7E] Audio RS-232 - Default [00] This is the code sent to the automation software that indicates that two-way audio has been initiated. If this option is set to '00' there will be no audio-initiated message sent to the automation output. If set to 01, the automation message for audio will be generated with protocol ID 'S'.
Example: 23 2300 Hz 18 1800 Hz 14 1400 Hz 10 1000 Hz IF Option 94 is set to 01 the ‘F’ will be replaced by a space and the value of “A” will be decoded as “A” but not “O”. This setting will also enable the receiver to decode special pulse extended-extended formats. 1011sssssss245sXssYZ If Option 94 is set to 02 than the leading zero of a four-digit panel account code will be stripped.
00 01 02 03 6500 protocol: 1RRLssssssAAAAXXYYYY[DC4] SG protocol: 6RRLssssssAAAAXXYYYY[DC4] ModemII to SIA protocol ModemII to SIA protocol, and text is decoded and sent to printer and computer. NOTE: Ensure that the automation software supports settings 02 and 03 if the SIA protocol is desired. 1234 03 1234 03 3333 01 3333 01 The DRL2E will interpret this information as 1234 301. Note that a longer on-line time is required for this format than for a standard 4/2 format.
Option [A5]: Sescoa Super Speed - Default [01] Option [A2]: Digit Replace - Default [00] If set to 00 Sescoa Super Speed will be disabled and 4/2 with checksum will be enabled. If set to 01, Sescoa Super Speed will be enabled and 4/2 with checksum will be disabled. Option 77 works in conjunction with Option A2. Option 77 is programmed with an ASCII value that will replace an account code digit or insert a value into an account code. Option A2 is used to replace a digit or insert a digit.
Section 7 - DRL2E Communication Formats 7.1 Common Formats The following formats are commonly used: • 3/1, 4/1, 4/2 formats; 10, 14, 20 Baud • 3/1 extended format; 10, 14, 20, 40 Baud. • 3/1, 4/2 formats with or without checksum; 40 Baud • 3-2 format; 10, 14, 20 Baud • 4/1 Extended format; 10, 14, 20 Baud • 4/2 Extended format; 10, 14, 20, 40 Baud Example: • 3/1 FORMAT • • 7.2 • 7.
7.9 7.7.1 Expected Output PRRLssAAAAAsXT1...Tns[DC4] Data: P = DMP protocol identifier ddddd=RRL replaced by the 5-digit DNIS, therefore increasing the length by two. s = Spaces AAAA = Account code X = DMP serial format identifier T1-Tn = Alarm information Examples: The ITI format covers ITI panel models RF Commander, Caretaker Plus, SX-V, SX-IVB, UltraGard 5000 (Pro 5000), Commander III and Commander 2000 Simon. In order to receive the ITI format, the handshake 0E must be programmed.
7.10 Modem II, Modem IIE, Modem IIIa² and BFSK Formats 7.9.4 Commander 2000 01-18 80 81 82 83 84 85 86 87 89 90 91 92 93 94 95 96 98 ALARM ALARM ALARM ALARM ALARM OPEN USER# CLOSE USER# SILENT DURESS FORCE ARMED RF TOUCHPAD AC FAILURE LOW CPU BAT ALM TAMPR LOOP AUTO PHONE TEST CPU RX FAIL CPU BACK IN FAIL TO COMMUNICATE EVENT DUMP REPORT BFSK, Modem II, Modem IIIa2 or Modem IIE formats can be decoded by the DRL2E. 7.10.1Modem II Example: • Modem II RS-232 Option ON • 7.10.
7.
E6zz EEzz E100 E2zz F000 F400 F1zz F5zz F2zz F6zz F3zz F7zz FD0a FF0a F8zz F9zz FAzz FBzz FC00 FE00 7.15.
Section 8 - CPM2 Central Processing Module Figure 9, CPM2 Front View 8.1 General Information The CPM2 16-bit microcontroller and real-time assembly language program running at 16 MHz allow the system to quickly and efficiently execute several tasks at the same time. The use of a unique menu display system enhances the system’s ease of use for the operator and makes the system configuration and programming simple and efficient.
8.4 CPM2 Operating Mode 8.4.
Option 05: COM1 Configuration Option [05] determines the Baud rate, data bits and parity to be used on COM1. Press the [ACK] button when the “05: Com#1 Config.” message is displayed; this message will be displayed: Sixteen 4-digit passwords are available for use on the CPM2. Password 0 is the Master password, and passwords 1 through F may be assigned to individual operators. Two letters, representing the initials of the operator, may be assigned to each password to help in identifying the operator.
Option 10: COM2 Communication Format Option [10] determines the application to be used on COM2. Press the [ACK] button when the “10: Com#2 Format” message is displayed; this message will be displayed: Enter a decimal number from 4.0 to 9.9. Use the [Enter] and [Backspace] buttons to move the cursor forward or backward when editing the acknowledge time. When programming is complete, press the [Escape] button; when the [Escape] button is pressed, the next Configuration option will be displayed on the screen.
Option 16: ComPort Diagnostics The CPM2 features a Diagnostics mode that allows the operator to view all data being communicated through COM1 (or COM2) on the display screen. To use this feature, press the [ACK] button when the “16: Debug ComPort” message is displayed; this message will be displayed: Option 13: Erase Alarm Message Buffer NOTE: Under normal operating conditions, the buffer should not be erased. Option [13] is used to erase the CPM2 alarm message buffer.
NOTE: When Diagnostics mode are enabled, messages will be displayed according to the following priority: • UL message - Acknowledge required • COM1 Diagnostic messages • Line Card Diagnostic messages • “Retain last message” displays • Internal Troubles messages • Standby mode message Refer to “Message Priorities” for more information.
2 3 4 Option 28: Tamper Input To view the Tamper Input / UPS Low Battery supervisory, press the [ACK] button until “28: Tamper Input” is displayed. Press [ACK], the following message will then be displayed: Send computer alarm messages only to Master central through COM2 for transmission to the SCADA DVL2A of the master receiver only. Send computer alarm messages to COM1 (local computer) and next to COM2 for DVL2A SCADA.
8.5.6 COM1 Absent 8.6.2 [B] Operator Log-On If Option 06 is enabled and COM1 is absent (for example, disconnects, off-line, or fails to send acknowledge signal), a message similar to this will be displayed: Different operators may “log on” to the system by entering this mode. When an operator logs on, a message similar to this one will be printed: “Operator on duty S.G. 11:03-21/12/92”; the operator’s initials (if programmed) and the time and date will be printed.
Enter a hexadecimal number to view the following: Enter... to view 00 CPM2 internal trouble messages (if any) 01to1E Computer messages for specified line card FF Computer messages for all line cards If an error is made in entering the number, simply reenter the desired number on the keypad. Press the [Backspace] or [Escape] button to cancel this function and return to the Standby mode, or, press the [Enter] button to view the indicated messages.
8.7 8.6.9 COM1 STATUS REPORT MESSAGES The CPM2 will send the following messages to COM1 to report internal status conditions. CPM2 will use an account code of “0000” to indicate that it is reporting an internal condition. The line number is fixed to be “0.” Sent to COM1Event 0000 A 00 Reserved to indicate Operator activity for C or ESC mode (not implemented in this program version).
Section 9 - Automation Protocols 9.2 The Sur-Gard MLR2E receiver sends the various protocols to report signals to the central station computer via an RS-232 port. The complete description of protocols is available upon request. 9.1 Acknowledgment of the Signal The Sur-Gard receiver requires an acknowledgment signal [ACK] (Hex 06) from the computer software within 4 seconds for each message sent.
Appendix A - DRL2E Communication Formats NAME HANDSHAKE DATA BAUD FORMAT EXTENDED KISS OFF Ademco Slow Ademco Slow Silent Knight Fast Silent Knight Fast Franklin Franklin Radionics Radionics Radionics 1400Hz 1400Hz 1400Hz 1400Hz 2300Hz 2300Hz 2300Hz 2300Hz 2300Hz 1900Hz 1900Hz 1900Hz 1900Hz 1800Hz 1800Hz 1800Hz 1800Hz 1800Hz 10bps 10bps 14bps 14bps 20bps 20bps 40bps 40bps 40bps 3/1,4/1(or 3/2),4/2 4/2,4/1,3/1 3/1,4/1(or 3/2), 4/2 4/2,4/1,3/1 3/1,4/1(or 3/2), 4/2 4/2,4/1,3/1 3/1,4/2 4/2,3/1 3/1+pa
Appendix B - ASCII Character Chart ASCII with library on printer (option 30) B0 B1 B2 B3 B4 B5 B6 B7 B7 B8 B9 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DC HEX Corresponding ASCII Character 20 30 31 32 33 34 35 36 37 38 39 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B Space 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z \ 40
Appendix C - Decimal - HEX - Binary Conversion Chart DEC HEX Binary DEC HEX Binary DEC HEX Binary DEC HEX Binary 000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 00 010 2 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2
Appendix D - Printer Words: Options [60-6F] The English Printer Library is provided and can be selected by programming the event codes to the corresponding word.
Hex # 7C 7D 7E 7F 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD Printer Words Hex # LOSS SUPERVISORY RF RESERVED RESERVED RESERVED RESERVED RESERVED COMMUNICATION TELCO 1 FAULT TELCO 2 FAULT LONG RANGE RADIO FAIL TO COMMUNICATE LOSS OF RADIO SUPERVISION LOSS OF CENTRAL POLLING VSWR RESERVED RESERVED PROTECTION LOOP PROTECTION LOOP OPEN PROTECTION LOOP SHORT FIRE TRO
Appendix E - Default Static Options Option 01 02 03 04 05 0E 0F 10 11 12 13 Description Default Option LINE # LINE # LENGTH DSC AUDIO AUDIO TIME PRE H.S.
Appendix F - Default Dynamic Options [30] - [AF] Line Card Configuration Command: LCard - Line Card Comd - Command(F7) Option Description 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 4/1 DIGIT#0 -A4/1 DIGIT#1 -A4/1 DIGIT#2 -A4/1 DIGIT#3 -A4/1 DIGIT#4 -A4/1 DIGIT#5 -A4/1 DIGIT#6 -A4/1 DIGIT#7 -A4/1 DIGIT#8 -A4/1 DIGIT#9 -R4/1 DIGIT#A=0 -A4/1 DIGIT#B -O4/1 DIG
Appendix G - Event Code Classifications The Event codes have been grouped according to the type of event, as described below.
WARNING Please Read Carefully
©2003 Digital Security Controls Ltd. Toronto, Canada • www.dsc.com Sales: 1-888-888-7838 Tech. Support (Canada & USA): 1-888-503-5869 Direct all comments concerning this publication to pubs@dscltd.
