Network Video Recorder User’s Manual User’s Guide FlexWATCHTM 5000 (Version. 3.0_Rev0) Seyeon Technology Co., Ltd www.flexwatch.com Seyeon Tech Co.
Network Video Recorder User’s Manual Table of Contents Overview of FlexWATCHTM Server ............................................................ 8 1 Packing List................................................................................................ 8 2 What is FlexWATCHTM NDVR server ?.............................................................. 9 2.1 Key Function of FlexWATCHTM 5000 ....................................................... 9 2.2 Product Specification ..........................
Network Video Recorder User’s Manual System Configuration ............................................................................ 33 1 System Information................................................................................... 33 2 Date & Time ............................................................................................. 33 2.1 Date & Time in the server clock........................................................... 33 2.2 Date & Time using NTP server ......................
Network Video Recorder User’s Manual 4.2 NIPP Port ......................................................................................... 52 4.3 NVCP –Rx Port .................................................................................. 52 5 WAN Configuration and Application .............................................................. 52 5.1 External Modem connection ................................................................ 52 5.2 Application with Dial-in/out feature ....................
Network Video Recorder User’s Manual Utilities.................................................................................................. 75 1 Save Configuration .................................................................................... 75 2 Reboot .................................................................................................... 75 3 Factory Default ......................................................................................... 75 4 System Update ............
Network Video Recorder User’s Manual Notice • The material in this document is for information only and is subject to change without notice. While reasonable efforts have been made in the preparation of this document to assure its accuracy, Seyeon Tech assumes no liability resulting from errors or omissions in this document, or from the use of the information contained herein. • Seyeon Tech reserves the right to make changes in the product design without reservation and without notification to its users.
Network Video Recorder User’s Manual Warning To prevent risk of electric shock, Do not remove system-case. No user serviceable parts inside. Any repair or modification for the product will be allowed to qualified service personal only. Do not expose this appliance to water or moisture. Do not install this product in Hazardous areas where highly combustible or explosive products are stored or used.
Network Video Recorder User’s Manual Overview of FlexWATCHTM Server 1 Packing List Please check and make sure following items are included in your package without any missing items. If there are any missing items, please refer to your local distributor. A. FlexWATCHTM 5000..…………………………………………………………………….1unit B. RS-232 Serial cable…………………………………………………………………..…1unit (Cross cable DB9 Female) C. Power Adapter…………………………………………………………………………..….1unit (Power Cable, SMPS DC 12V Adapter) D.
Network Video Recorder User’s Manual 2 What is FlexWATCHTM NDVR server ? FlexWATCHTM 5000 is a stand alone network video recorder server which is designed to record real time JPEG video streams transmitted from any FlexWATCH™ network camera and video server series over the TCP/IP network. It supports rate up to 60fps for recording over the existing network such as LAN, leased line, DSL, Cable modem.
Network Video Recorder User’s Manual 2.2 Product Specification Hardware 32bit Embedded Processor Flash Memory: 4Mbytes SDRAM: up to 64Mbytes Disk Format Support both FAT32 for window and Linux file format (Default) Network Protocols HTTP, TCP/IP, FTP, Telnet, ARP, RARP Supported Hard Disk Following HDD has been tested and recommended to use. - Seagate : 60G & 80G - Maxtor : 40G, 80G, 120G, 250G - Samsung : 40G, 80G, 120G, 250G Recording & Performance Recording from up to 16channel.
Network Video Recorder User’s Manual 2.3 Application FW-5000 is born to secure on-site video recording over the TCP/IP network satisfying the need for reliable, flexible and distributed on-site video recording in the TCP/IP based remote video surveillance industry. By combining with FlexWATCHTM network Camera or video server series, following can be suggested application area.
Network Video Recorder User’s Manual Hardware Description • This chapter contains list of items to be prepared for the installation of FlexWATCHTM NVR server. • Please carefully read this chapter before the installation. • Please prepare all the necessary items before start installation to prevent any possible malfunction or any other hazard can be happened during the installation. 1.1 Caution and observance • Keep the device in the clean and dried area where air ventilation is guaranteed.
Network Video Recorder User’s Manual [Details of LED Part] Menu Description Name Description A Power ON/OFF Switch B PWR LED To turn on/off the power WARNING! You must turn off the Power using this Switch when you turn off the unit. Otherwise HDD can be damaged by sudden power shut down. To show Power status LED will turn RED when the power is on. C STATUS LED To show recording status and power shut down status. When [Recording Status] is on Running, LED turns ORANGE color.
Network Video Recorder User’s Manual Rear Panel View A A WAN B Aux C LAN D COM E DC12V B C D E LAN Port for 10/100M Base T Auto sensing. LAN, Cable or DSL modem should be connected to WAN port. RS-232 Port to connect Serial input device, Voice kit, PTZ device or Modem. Modem must be connected to Aux Port only. Console for Hyper Terminal is not supported by this port. LAN Port for 10/100M Base T Auto sensing.
Network Video Recorder User’s Manual IP assignment 1 Key Words for Network LAN (Local Area Network) : Under the LAN network, any network device in the same LAN network can be accessed by any other network device. But LAN network can not be accessed from the Internet (WAN). Most of case, LAN is built after Router which is connected to WAN network so that Network device in the local area network can access to the Internet through Router.
Network Video Recorder User’s Manual assigned to a client station (computer, network equipment, etc.) in a TCP/IP network. Dynamic IP address is typically assigned by a DHCP server, which can be a computer on the network or another piece of hardware, such as router. A dynamic IP address may change every time your computer connects to the network DHCP (Dynamic Host Configuration Protocol) : DHCP is software that automatically assigns IP addresses to client stations logging onto a TCP/IP network.
Network Video Recorder User’s Manual AOIP (Always On Internet Protocol) Server: AOIP™ server (Always On IP) is run by Seyeon Technology or its business partner and is a gateway for remote users to access FlexWATCH™ servers which is connected dynamic IP address over DSL,Cable modem and PSTN network over the Internet.
Network Video Recorder User’s Manual \ C:\> ipconfig Windows 2000/XP IP Configuration Ethernet adapter Local area connection : Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.0.158 Subnet Mask . . . . . . . . . . . : 255.255.255.0 Default Gateway . . . . . . . . . : 192.168.0.1 C:\> With above info, you can get information about your network from your PC and see which IP class of IP address should be assigned to FlexWATCHTM server.
Network Video Recorder User’s Manual 2.1.2 DHCP Enabled PC If your PC is set to use DHCP, you need to check out IP address of your PC using ‘ ipconfig’ command at DOS Prompt window. You need to get IP address from your network administrator to assign it to FlexWATCHTM server. IP address should be Surplus of IP address which will be not randomly assigned to any network device in your network.
Network Video Recorder User’s Manual 2.2.2 Cross-over cable If LAN network is not available, you can directly connect FlexWATCHTM server to your PC through Cross-over cable. In this case, you need to prepare Cross-over cable separately (Note that The LAN cable included in the product package is not Cross-over cable, but normal straight cable) and you need to set your PC IP address as 10.20.30.41 and connect the server with Factory default IP address, 10.20.30.40 through web browser.
Network Video Recorder User’s Manual 3 Factory Default Please refer to the following factory defaults to change setting up. Factory Default Admin ID Admin password IP address Network mask root root 10.20.30.40 255.255.255.0 4 IP Assignment FlexWATCHTM server can be configured by two different configuration method and following is brief explanation. Installation Wizard Program: IP installation program is provided in CD form.
Network Video Recorder User’s Manual Rear View of FlexWATCHTM NVR server WAN Port (eth1) LAN Port (eth0) Network Diagram A B A. Only WAN Port needs to be connected to the network when FlexWATCHTM NVR server is connected to Public IP network or HUB in your Local Network. B. Connect local HUB to LAN port of the server to set up Private LAN network under builtin router, while WAN Port is connected to Public Network.
Network Video Recorder User’s Manual 4.2 Through Installation Wizard Program IP setting with Installation Wizard program is easy and simple way and after IP setting is done you can do other configuration through web browser. You can use IP Installation Wizard Program through following step. (IPInstallationWizard.exe is provide in the product CD) 1) Connect FlexWATCHTM NVR server (WAN port) into the network (Hub) that your PC is belong to. 2) Run the IP installation Wizard program in your PC.
Network Video Recorder IP Address C IP, Subnet, Gateway D ‘Set IP Address’ Button E ‘Save IP Address’ Button F ‘Go to Home Page’ Button G ‘Telnet to System’ Button H Result window User’s Manual Input an IP address to be assigned to FlexWATCHTM server Note that the IP must be directly connectable with user’s PC. The above IP ’10.10.225.100’ is only an example. Whether to change IP, Subnet and Gate or IP and Subnet mask only. To activate a new IP assignment, click this button.
Network Video Recorder User’s Manual 8) Click “Save IP Address” button to save IP-Address in the Flash Memory. 9) Click “Go to Home Page” button to access to FlexWATCHTM Web browser. 10) For server configuration, click “Admin” Icon and Input User ID and Password (Factory default is root : root) to get into configuration mode and then press “OK” button. Note Once you changed the IP address of FlexWATCHTM NVR server, you need to connect the server with the changed IP address.
Network Video Recorder User’s Manual 3) If Hyper Terminal window come up as below, input HyperTerminal name (ex. Flexwatch) and press ‘OK’ button. 4) Select the connected COM port with serial cable and press OK button. 5) When ‘Port Settings’ window show up, input each values from the table below. 26 Seyeon Tech Co.
Network Video Recorder User’s Manual Serial Port Settings Bits per Second Data bits Parity Stop bits Flow control Value 115200 8 None 1 None 6) After setting Hyper Terminal, press Enter key several times and then you can see messages as below. Input Login ID and Password. (Factory defaults for Admin ID and Password are root/root.) Seyeon Tech Co., Ltd. 2001-2003 Linux Kernel 2.4.20-syl1 FlexWATCH login: 7) If you correctly input ID and Password, ‘bash#’ prompt will show up as below.
Network Video Recorder User’s Manual bash# bash# netconfig eth1 10.10.222.30 255.255.0.0 10.10.1.1 Your network configuration was changed.
Network Video Recorder 10) User’s Manual Input ‘savecfg’ command to save the changed configuration to Flash Memory. And Input ‘reboot’ command to reboot the system. bash# bash# savecfg Saving a current config to flash memory [ OK ] Updated flash bash# bash# bash# reboot Broadcast message from root (ttyp0) Mon Sep 6 19:28:51 2004... The system is going down for reboot NOW !! bash# 29 Seyeon Tech Co.
Network Video Recorder User’s Manual Live view Once IP assignment is finished and external FlexWATCHTM network Camera or video server is registered in the FW-5000 server, you can view live video from network camera or video server through standard web browser such as MS Internet Explorer. Note that to view live from external FlexWATCHTM network Camera or video server, Rx Module registration must be done beforehand.
Network Video Recorder User’s Manual When the Client pc is not connected to internet, you need to manually install ActiveX components in your viewing PC. - Insert the product CD in your PC - Select “FlexWATCH Simple Viewer control” program - Application idea ActiveX based SDK is provided for software developers so that application program developers can easily utilize digital video from FlexWATCHTM server for his own video application.
Network Video Recorder User’s Manual through Rx Module registration process, list of server will be shown in the Selected module column as a Server module. Note that only cameras connected to the selected module can be displayed one at a time. Cam Control : By checking the camera you can get any number of camera displayed on the same screen. Camera 1, 2, 3, 4 and all cameras can be displayed together. Sequence : To view camera selected camera sequentially.
Network Video Recorder User’s Manual System Configuration System configuration is to set up basic functions which helps you properly run and manage the system. It is highly recommended to set up the configuration before any other configurations. Following functions are provided in the System configuration mode.
Network Video Recorder User’s Manual 2.2 Date & Time using NTP server If multiple servers are installed over the network and controlled by client program and synchronized time info is required, use NTP(Network Time Protocol) option. 1) Go to [NTP setup] menu in the Network configuration section of Admin Mode 2) Type in NTP server name or use default NTP time server, ntp.ewha.net, if you do not know any NTP time server available in your area. Note NTP time server provide exact time wherever it is located.
Network Video Recorder User’s Manual control 4.1 Full Access To allow system access by anyone who know the IP address. PTZ, Audio and Relay output device can be controlled by anyone. Thus, if security for video is important, it is higher recommended to user limited access mode below 4.2 Limited Access and User registration This is to limit server access to the authorized user only.
Network Video Recorder User’s Manual Full Access : If full access is selected, any body can access the server and control the video. No Access : This is to temporally restrict camera access by specific user without delete user account to temporally block access to the camera. Selective Access: This is to set up control authority for the respective or all camera. VS Module ID is FlexWATCHTM server ID which is recognized by the server. Default # is 0.
Network Video Recorder User’s Manual 5 Frame rate control Maximum Video frame rate which sever can transmit over the IP network can be set up through Frame rate control option. Through this maximum frame rate control option, user can limit network bandwidth consumption by video transmission. 1) Go to [Access Control] option in the system configuration menu in the Admin page. 2) Set up Maximum frame rate. Following table could be an example. File size is variable depending on the complexity of the scene.
Network Video Recorder User’s Manual 6 Rx Module Registration Video proxy function is supported by NDVR server such as FW-5440 and FW-5000 servers. By registering networked FlexWATCHTM network camera or video server into NDVR server, video recording can be done in the NDVR server and live view can be accessed through NDVR server web page which means user does not need to separately run web browser to view live view from respective cameras from FlexWATCHTM video servers.
Network Video Recorder User’s Manual and NDVR depending on the network environment Video server (TX module) Connection type Passive Passive Passive Active Active NDVR Server (RX module) Network environment WAN Network(Global Static) LAN Network (Private) LAN or WAN with AOIP server connection LAN Network (Private) WAN Network(Global Static) Connection type Active Active Using AOIP server Passive Passive Network environment LAN network (Private) LAN Network (Private) LAN or WAN network WAN network (Glo
Network Video Recorder User’s Manual no performance stability can be guaranteed. 3) Select “Enable” option and type in the right information in the each filed. Connection type : Select the right connection type. Name : Type in user defined name of Server module. Model : Select the right type of series of model. No specific model can be selected. Note that some series of model is not available right now such as 4200,4600,5800,. etc. Following is information about the series of FlexWATCH™ Models.
Network Video Recorder User’s Manual FW-5400 Series = FW-5440 VS Module ID: Select “0” for any selected Video Server module, number 1 ~ 15 is for video expansion in each video server in the future expansion. NVCP Port : Type in NVCP port number configured in the network camera or video server. NVCP Password : It is security feature reside in the FlexWATCHTM server which authenticate server access by RX module (FW-5440 or 5000 NDVR server) to FlexWATCHTM server.
Network Video Recorder User’s Manual port and Pass word must correctly be configured. Following is captured setting of TX module configuration in the FW-3440. Note NVCP port should be open to communicate with NDVR Server, when the FlexWATCHTM server is programmed to be Passive mode. 6.2.2 Passive Mode Following is captured setting when the server is configured as Passive mode. MAC address of Vs Module(Network camera or video server) should be type in to authenticate access by FlexWATCHTM server.
Network Video Recorder User’s Manual Following is captured setting of TX module configuration in the FW-3440, when it is set up as Active mode. Note NVCP port at NDVR server side should be opened to internet so that FlexWATCHTM server can connect the NDVR server. If NDVR and FlexWATCHTM server is in the LAN network, user does not need to configure NVCP port. But if either of them is in the WAN network, NVCP port must be opened to internet so that video can be transmitted to NDVR server. 6.2.
Network Video Recorder User’s Manual no connection can be established. NVCP Password for FlexWATCHTM server must correctly be configured. Following is captured setting of TX module configuration in the FW-3440. FlexWATCHTM server should be configured as Passive Mode. 44 Seyeon Tech Co.
Network Video Recorder User’s Manual Network Configuration NDVR Server, FW-5440 and FW-5000, has two different LAN card (WAN Port and LAN Port) and has built-in router so that external FlexWATCHTM network camera or video servers can be installed under the NDVR server network. This option is very useful when user want to install more than 1 network camera or video server on the single WAN network and selectively view all camera thorough NDVR server web page.
Network Video Recorder User’s Manual 1.2 DHCP Client This setting is recommended when the server is installed under DHCP environment in the LAN or Cable modem, xDSL Modem which provides PPPOA type service. We recommend you to use DHCP option when the server is directly connected to Cable modem only. 1.2.1 How to access the server under DHCP environment Once DHCP is enabled, there is no way for the user to know which IP is assigned to the server from the server web page.
Network Video Recorder User’s Manual 1) Check whether you are in the DHCP environment before starting set-up. 2) Go to [Network Status Notify] menu in the network configuration mode 3) Set up e-mail account through which you would like to get IP address information when the server is set up DHCP Client. 4) Now go to LAN configuration mode and select DHCP option 2.1.1.
Network Video Recorder User’s Manual Please contact your local ISP to get User ID and Password for your internet connection. And input the User ID and Password in the option field above. Note Once PPPoE is enabled, LAN network setting will be disabled. 2 Local Network Local Network configuration in the NDVR server is to set up separate private network. In this case NDVR server act as a network gateway for local devices connected to the NDVR server.
Network Video Recorder User’s Manual IP Address : IP address of this NDVR server which is default gateway for local device. Netmask : Multiple class of private network can be set up through this Netmask (A class:255.0.0.0, B class:255.255.0.0, C class : 255,255,255,0) DHCP Server : NDVR sever act as a DHCP server when it is enabled and IP for local device will automatically assigned. It is highly recommended to disable DHCP option and give static IP address for the local device.
Network Video Recorder User’s Manual assign any port number with the range. But be sure that the port number is not duplicated by other device as well. Internal port : It is a port assigned to Local device. Internal IP address : IP address of local device such as FlexWATCHTM network camera or video server Note FTP (Port#21) and Telnet (Port#23) for FlexWATCHTM network camera or video server is not user definable. But HTTP, NVCP, NIPP, UDP port is user definable 3.
Network Video Recorder User’s Manual How to access to the FlexWATCHTM server If IP address of NDVR server is 211.177.68.47 and External Port number is 1080, you need to type in NDVR server IP address and External port number in the URL field of web browser so that you can access to the 1st FlexWATCHTM server (192.168.1.200). HTTP://211.177.68.
Network Video Recorder User’s Manual feature of Router, you can install more than one server behind the router. For more information about this, please contact your local vendor. 4.2 NIPP Port This is port through which archived video can be playback through internet net. If NIPP Port is not open to internet no recorded video can be playback. This port number is user definable. 4.
Network Video Recorder User’s Manual 1) Connect your MODEM and AUX Port at FlexWATCHTM server with RS-232 Serial cable. 2) Go to Admin Menu >> System Configuration >> Serial Ports Configuration 3) Select ‘Modem’ at AUX mode and click ‘Apply’ button. 4) System reboot will be recommended, then click ‘Reboot’ button. 5.2 Application with Dial-in/out feature 5.2.1 Application with Dial-in Dial-in is to allow server connection from remote client.
Network Video Recorder User’s Manual Dial-out through standard PSTN modem is quite common and general. 1) Connect the server to PSTN line through RS-232 cable. Connect the cable to COM Port or server. Use the standard D-Sub 9pin connector provided by PSTN modem. 2) Go to [WAN (PPP, Modem, etc)] menu in the Network configuration mode 3) Select “PPP client” option and fill out the option field. PPP Client : This means that FlexWATCHTM server act as client and call out to ISP.
Network Video Recorder User’s Manual distributor or contact sales@flexwatch.com to choose compatible modem. 5.3.2 Dial-Out through Media specific device Dial-out can be done through specific media which is not standard PSTN such as CDMA modem, GSM or GPRS Modem or any type of wireless modem. This mode is not for general users. Thus, if you need to connect special modem device, please contact your vendor or manufacturer for more information, sales@flexwatch.com 5.
Network Video Recorder User’s Manual When remote client is connected to the server through modem connection, physical line connection will be done. But no way to view live video unless client run the web browser of the FlexWATCHTM server. Local IP address and Remote IP address is virtual IP address which is used at the time of Modem connection only Local IP address : System default IP address (192.168.2.1) resides in the FlexWATCHTM server for modem connection only.
Network Video Recorder User’s Manual • When the DHCP option is selected • When the PPPoE option is selected 1) Go to [Network Status Notify] menu in the network configuration mode 2) Set up e-mail account through which you would like to get IP address information when the new IP address is assigned to the server and click “Apply” button 7 Service patch This is to specify service path through which server can send any information to target device.
Network Video Recorder User’s Manual LAN : This is default path the send any data to outside. Modem : when PSTN or other medium than LAN is used to send data to outside. This service port must be checked when any data is to be sent through PSTN or other medium than LAN which is connected to COM port. Note Service patch must be set up and checked before starting WAN configuration to send any data through external PSTN modem connection or equivalent If LAN is to be used, select “None(LAN)” option.
Network Video Recorder User’s Manual 8.2 AOIP configuration As described above, once you register product in the AOIP server and Network setting is correctly done to user AOIP function, you need to configure AOIP function in the FlexWATCHTM server. 1) Check the “Enable” option to use AOIP function 2) Type in AOIP server address. Either Domain name or IP address can be typed in. 3) Select whether to use HTTP or NVCP-TX port.
Network Video Recorder User’s Manual 60 Seyeon Tech Co.
Network Video Recorder User’s Manual Recording & Playback 1 General Setting for Recording 1.1 Hard Disk Configuration 1.1.1 Before Installing HDD Make sure that system is properly shut down before you install or detach HDD from the server, since there is high possibility that File system may be affected by improper handling of HDD. Make sure that Jumper of HDD is on Master position before you install HDD. Otherwise, HDD will not be recognized by the server.
Network Video Recorder User’s Manual HDD and manually install and format to start recording. Please make sure that Network configuration should be done before HDD installation 1) Shut down the system by turning off the power 2) Remove HDD Rack from the NSS and assemble HDD with HDD Rack 3) Insert the HDD Rack and lock the HDD Rack using key lock which come with HDD Rack. If it is unlocked, no recording can be done.
Network Video Recorder User’s Manual HDD SIZE Manufacturer Model Decription 30G 40G Samsung Samsung Seagate Maxtor Samsung Seagate Maxtor Samsung SpinPoint SV3063H/DOM SpinPoint SP4002H/DOM Barracuda ATA IV ST340016A Fireball 3 2F040J0310201 SpinPoint SV6003H/DOM Barracuda ATA IV ST360021A DiamondMax 16 4R60J0220201 SpinPoint SP8004H/DOM Seagate Maxtor Samsung Seagate Maxtor Maxtor Maxtor BarracudaATAIV Model ST380021A DiamondMax Plus 9 6Y080L0030413 SpinPoint SV1204H/DOM Barracuda ATA V ST3120023A
Network Video Recorder User’s Manual B. Complete HDD Format If the second-hand HDD is to be used for the NDVR server or HDD bad block check up is required for more secure video recording, this option is highly recommended. Simple Check “File system type” and check “ Check Bad Block” option and Press “Partition and Format” button. Note that “Check Bad Block” option take a few hours to complete the task. The bigger the HDD, the longer the HDD format time.
Network Video Recorder User’s Manual 1.3 HDD Status Report HDD status can be sent to user defined e-mail account so that user can get HDD status from the server. Disk Full and Periodic status information can be sent to user’s e-mail account. 1) Go to “HDD Status Report” menu in the Recording configuration window of Admin page. 2) Fill out the option field and click “Apply” button Disk Full Notification : To send e-mail when the HDD is full.
Network Video Recorder User’s Manual 2 Recording Configuration Networked external FlexWATCHTM network camera or video server registered in the NVR server can be recorded in the NDVR server over the TCP/IP network. 2.1 Recording Configuration Procedure If networked external FlexWATCHTM network camera or video server is to be recorded, please make sure that FlexWATCHTM network camera or video server is registered in the NVR server through Rx Module registration option beforehand.
Network Video Recorder User’s Manual 4) Once recording condition is set up, go back to initial page of Recording configuration menu. 5) And press “Record” button to start recording. If you skip this process, no recording can be done in the HDVR server. 6) If there was any recording condition change while the server is on Recording mode, then you need to simply press the “Apply” button. 2.
Network Video Recorder User’s Manual on the situation. By using this option user can record video at a slow speed on a continuous mode and do fast recording on event condition. Pre-Recording Speed: It is basic recording frame rate which can be recorded in the NDVR system before any alarm happens. Once Pre-Recording Speed is set up, NDVR server is to try to get as many video frame as Pre-Recording Speed. Pre-Alarm Count : This is Pre Alarm image before event happens.
Network Video Recorder User’s Manual Note that built-in camera server support motion detection function as well. 2.4 Recording condition The basic logic for Recording condition set up is same as those of Advanced service menu. Please refer to Advanced Service menu for more information about Recording condition. 2.5 Recording condition example Following is a few example about the setting for the recording condition. 2.5.
Network Video Recorder User’s Manual Video recording for Camera 1 from 8:00 AM to 10:00 PM for the weekday only from March to October. No recording on Saturday and Sunday. 2.5.3 Event based recording Event Based Recording means that video recording will be done only when pre-configured event condition is triggered by any event. Condition: - Video recording for Camera 1 when the Motion detection is triggered at any cameras.
Network Video Recorder User’s Manual Note If you do use Motion detection option, please make sure that Motion detection is supported and configured by the server. Application Idea Above condition is to record video for Camera 1 can be done when alarm input, Motion detection or Camera detection is happened at different cameras. With this application, you can record specific camera when the event is trigged at other cameras. 2.5.
Network Video Recorder - User’s Manual Video recording for Camera 1 when the Motion detection is triggered at any cameras. - Video recording for Camera 1 when Alarm input (Normal Close Type) number # 2 and 3 is triggered. - Video recording for Camera 1 when camera disconnection is detected at any cameras 72 Seyeon Tech Co.
Network Video Recorder User’s Manual 3 Playback of Archived Video Any archived video in the NDVR server can remotely playback through separate NDVR player program over the TCP/IP network. NDVR Player software is ActiveX based one. Thus, it can automatically downloaded in client’s viewing pc, once Client’s PC is connected to the internet. If it is not connected to internet, manual software installation is required. NDVR software is provided in the product CD or can be download from www.flexwatch.com.
Network Video Recorder User’s Manual 4) When security warning window come up, click “Yes” to install the program. Then program will automatically installed in your PC. Now the NDVR player software is successfully installed in your PC. For more information about the function and operation of NDVR software, please refer to separate User Manual for FlexWATCHTM NVR Player Software in the Product CD.
Network Video Recorder User’s Manual Utilities Utilities is to manage and control system properly. Save Configuration, Flash Update, System Reboot and system upgrade options are provided. 1 Save Configuration This is to temporally save all new configuration and settings in the system memory. Once new configuration is saved by “Save Configuration” menu, new configuration will permanently saved in the system memory only after system Reboot.
Network Video Recorder User’s Manual 4 System Update System update can remotely be done through web page of the system or ftp option with telnet and Hyper Terminal mode. In this user manual only web based system update method is described and ftp based system update method can separately provided. 4.1 Description of files system FlexWATCHTM Server has 4 different files to get the system work. In some case, you may need to upgrade whole files or other case you need to upgrade some specific file only.
Network Video Recorder User’s Manual All (kernel, RAM disk, System, Web) Update: To completely update all the system for Kernel, RAM Disk, System and Web all together except PTZ Device Driver or Sensor Device Driver. This option is recommended if there is special notice by manufacturer. Generally Complete system update comes only when there is big change for all of the system software. System and Web Update: To update system and web related software together.
Network Video Recorder User’s Manual 3) Browse your pc and select the right file to update following the update guide. If you want to skip specific update, click “Skip” button. 4) Once update is successfully done following result will come up. 5) If you want to update RAM Disk, System and web page, please click “Next” button follow the web guide to update more files. 78 Seyeon Tech Co.
Network Video Recorder User’s Manual 6) If all of file update is finished “System Reboot” window will come and do system reboot to apply new update. 79 Seyeon Tech Co.
Network Video Recorder User’s Manual Warranty Product Network Video Server Model S/N FlexWATCHTM 5000 A/S Seyeon Tech Ltd. Warranty 1 year Limited +82-2-3017-0866 Seyeon Tech Co., Ltd. TEL : +82-2-3017-0855 FAX : +82-2-3017-0843 http://www.seyeon.co.kr http://ww.flexwatch.com A/S Center: Tel : +82-2-3017-0855 Fax: +82-2-3017-0843 80 Seyeon Tech Co.
