Network Video Server User’s Manual User’s Manual FlexWATCHTM 1160 series (Version. 3.0_Rev1) Seyeon Technology Co., Ltd www.flexwatch.com www.intplus.es 1 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual NOTE This User Manual has been released as beta version, so any information in this manual can be subject to be updated without prior written notice. 2 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual Table of Contents Overview of FlexWATCHTM Server ................................................ 10 1 Packing List ............................................................................................... 10 2 What is FlexWATCHTM? ................................................................................ 11 2.1 Key Function of FlexWATCHTM ................................................................ 11 2.2 Product Specification ...........................
Network Video Server User’s Manual 3.2 Camera configuration .......................................................................... 51 3.3 Video Motion Detection ........................................................................ 52 System Configuration .................................................................. 55 1 System Information.................................................................................... 55 2 Date & Time .......................................................
Network Video Server User’s Manual 6.2 AOIP configuration .............................................................................. 73 7 Network Status .......................................................................................... 74 External Device connection & configuration................................. 75 1 Serial Ports Configuration Guide ................................................................... 75 1.1 Hardware Description ................................................
Network Video Server User’s Manual 5.2 Playback of Pre/post alarm Image ........................................................101 6 Sensor Notification service..........................................................................102 Utilities ...................................................................................... 104 1 Save Configuration ....................................................................................104 2 Reboot....................................................
Network Video Server User’s Manual Notice • This User Manual is only for following FlexWATCHTM Network PTZ camera server models; - FW-1160/FW-1160E/FW-1160S/FW-1160SE ) FW1160 and 1160S are provided with an indoor housing, while FW1160E and 1160SE are provided with an outdoor housing. • The material in this document is for information only and is subject to change without notice.
Network Video Server User’s Manual 8 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual Warning To prevent risk of electric shock, Do not remove system-case. No user serviceable parts inside. Any repair or modification for the product will be allowed to qualified service personal only. Do not expose this appliance to water or moisture. Do not install this product in Hazardous areas where highly combustible or explosive products are stored or used.
Network Video Server User’s Manual Overview of FlexWATCHTM Server 1 Packing List Please check and make sure following items are included in your package without any missing items. If there are any missing items, please refer to your local distributor. A. FlexWATCHTM 1160 / 1160S with a Bracket…………………………………………………….1unit or A. FlexWATCH TM 116E / 1160SE with a Bracket…………………………………………………….1unit B. RS-232 Serial cable…………………………………………………………………..…1unit (Cross cable DB9 Female) C.
Network Video Server User’s Manual 2 What is FlexWATCHTM? The FlexWATCHTM server is the Network camera Server, which transmits digital images captured by Analog CCD camera over the Internet. So users can view real-time live images over the Internet at anytime and anywhere using the standard web browser such as MS Internet Explorer or Netscape Communicator. There is no need other specific software to view real-time live images over the Internet.
Network Video Server User’s Manual 2.2 Product Specification Hardware · · · · Others 32bit Embedded CPU Flash 4Mbytes /SDRAM: 64Mbytes Hardware Motion JPEG engine Linux version 2.4.
Network Video Server User’s Manual 2.3 Mounting Bracket Specification 2.3.1 In-door Mounting Bracket for FW-1160 & 1160S FSD-230CB (weight: 400g) 13 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual FSD-230WB (weight: 500g) 14 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual FSD-230ICB (weight: 250g) 15 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual 2.3.2 Out-door mounting bracket for FW-1160E & 1160SE Wall mount bracket (weight: 4.3Kg) 16 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual Ceiling mount bracket (weight: 3.8Kg) 17 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual 18 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual 2.4 Basic Network Connection Diagram FlexWATCHTM server provides flexible connectivity with any type of networks available around you such as Leased line, Cable modem, xDSL line and PSTN (POT) line. Thus, it can be installed either in LAN or WAN environment as long as there is network available. But its configuration is subject to change depending on its environment. Following is basic network diagram for using FlexWATCHTM server.
Network Video Server User’s Manual FW-1160 2.4.3 Dynamic IP address from Cable or xDSL line FlexWATCHTM server can be installed on even Dynamic IP network. But it needs to be registered in AOIP server which is an IP gateway running by Flexwatch.com or your local Distributor. For more details, please refer to Technical guidebook in the CD manual. FW-1160 20 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual 2.4.4 Dial-up to AOIP server Using Dial-up function of FlexWATCHTM server and AOIP service, you can set the FlexWATCHTM server to make a call to ISP and get it connected AOIP server. Once FlexWATCHTM server is registered in AOIP server, you can connect FlexWATCHTM server through AOIP server.
Network Video Server User’s Manual 2.5 Application Unlimited application for remote monitoring and surveillance solution can be built up using FlexWATCHTM server and its supporting peripheral Hardware and software such as FW-5000 or FW-5440 Network video recorder server and FW-Manager DVR software. Following could be simple application area where FlexWATCHTM server can be applied. A. Building live home pager for advertising. B. ITS (Intelligent Traffic System) for real time monitoring C.
Network Video Server User’s Manual 3 Hardware Description • This chapter contains list of items to be prepared for the installation of FlexWATCHTM server. • Please carefully read this chapter before the installation. • Please prepare all the necessary items before start installation to prevent any possible malfunction or any other hazard can be happened during the installation. 3.1 Caution and observance • Keep the device in the clean and dried area where air ventilation is guaranteed.
Network Video Server User’s Manual 3.2 Hardware Description 3.2.1 FW-1160 Hardware Description External ports View and Pin-out FW1160 models have 2 external cables, LAN/PWR & COM/DI,DO, which are divided into 2 ports at the end of each cable. Below is the pin-out information of it. LAN,PWR port LAN,PWR 87654321 87654321 PWR - - Available Devices LA + LAN, PWR port COM, DI/O port Pin No. LAN cable O 1,2,3,6 Power (AC24V, 1.
Network Video Server User’s Manual Marcador no definido. IP assignment 1 Key Words for Network LAN (Local Area Network) : Under the LAN network, any network device in the same LAN network can be accessed by any other network device. But LAN network can not be accessed from the Internet (WAN). Most of case, LAN is built after Router which is connected to WAN network so that Network device in the local area network can access to the Internet through Router.
Network Video Server User’s Manual Depending the network Public Static IP(WAN) or Private Static IP can be assigned to network device. Dynamic IP address : A dynamic IP address is an IP address that is automatically assigned to a client station (computer, network equipment, etc.) in a TCP/IP network. Dynamic IP address is typically assigned by a DHCP server, which can be a computer on the network or another piece of hardware, such as router.
Network Video Server User’s Manual multiple IP addressed on the private LAN to one public address that is sent out to the Internet. This adds a level of security since the address of a PC connected to the private LAN is never transmitted on the Internet.
Network Video Server User’s Manual 2.1.1 Static IP address enabled PC (DHCP Disabled PC) You can easily check whether Static IP address is assigned to your PC. If you are in the Static IP network, it is simpler to assign IP address to FlexWATCHTM server than DHCP network. C:\> ipconfig Windows 2000/XP IP Configuration Ethernet adapter Local area connection : Connection-specific DNS Suffix . : IP Address. . . . . . . . . . . . : 192.168.0.158 Subnet Mask . . . . . . . . . . . : 255.255.255.
Network Video Server User’s Manual Reply from 192.168.0.155: bytes=32 time=10ms TTL=128 Reply from 192.168.0.155: bytes=32 time<10ms TTL=128 Reply from 192.168.0.155: bytes=32 time<10ms TTL=128 Reply from 192.168.0.155: bytes=32 time<10ms TTL=128 2.1.2 DHCP Enabled PC If your PC is set to use DHCP, you need to check out IP address of your PC using ‘ ipconfig’ command at DOS Prompt window. You need to get IP address from your network administrator to assign it to FlexWATCHTM server.
Network Video Server User’s Manual Check out whether FlexWATCHTM server can be connected through LAN cable or Cross-over cable. 2.2.1 LAN Cable Environment If your PC is connected to network through LAN cable, you need to connect FlexWATCHTM server to LAN port of Hub or Router. 2.2.2 Cross-over cable If LAN network is not available, you can directly connect FlexWATCHTM server to your PC through Cross-over cable.
Network Video Server User’s Manual 2.3 PC Environment Check out whether your PC is connected to LAN or WAN network or stand-alone. If stand alone, you need to use Cross-over cable or build up LAN environment to use LAN cable. 3 Factory Default Please refer to the following factory defaults to change setting up. Factory Default Admin ID Admin password IP address Network mask root root 10.20.30.40 255.255.255.
Network Video Server User’s Manual done you can do other configuration through web browser. You can use IP Installation Wizard Program through following step. (IPInstallationWizard.exe is provide in the product CD) Preset a PC with Microsoft Windows O/S. 1) Connect FlexWATCHTM server into the network (Hub) that your PC belongs to. 2) Run the IP installation Wizard program in your PC. Then following IP Installation Wizard window will show up.
Network Video Server IP Address C IP, Subnet, Gateway D ‘Set IP Address’ Button E ‘Save IP Address’ Button F ‘Go to Home Page’ Button G ‘Telnet to System’ Button H Result window User’s Manual Input an IP address to be assigned to FlexWATCHTM server Note that the IP must be directly connectable with user’s PC. The above IP ’10.10.225.100’ is only an example. Whether to change IP, Subnet and Gate or IP and Subnet mask only. To activate a new IP assignment, click this button.
Network Video Server User’s Manual 8) Click “Save IP Address” button to save IP-Address in the Flash Memory. 9) Click “Go to Home Page” button to access to FlexWATCHTM Web browser. 10) For server configuration, click “Admin” Icon and Input User ID and Password (Factory default is root : root) to get into configuration mode and then press “OK” button. ) Note Once you changed the IP address of FlexWATCHTM server, you need to connect the server with the changed IP address.
Network Video Server User’s Manual 4) Select the connected COM port with serial cable and press OK button. 5) When ‘Port Settings’ window show up, input each values from the table below. Serial Port Settings Bits per Second Data bits Parity Value 115200 8 None 35 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual Stop bits Flow control 1 None 6) After setting Hyper Terminal, press Enter key several times and then you can see messages as below. Input Login ID and Password. (Factory defaults for Admin ID and Password are root/root.) Seyeon Tech Co., Ltd. 2001-2003 Linux Kernel 2.4.20-syl1 FlexWATCH login: 7) If you correctly input Login ID and Password, ‘bash#’ prompt will show up as below.
Network Video Server User’s Manual Enter IP Address : 10.10.213.22 Enter Network Mask : 255.255.0.0 Enter Gateway : 10.10.1.1 Entered network configuation IP Address : 10.10.213.22 Network Mask : 255.255.0.0 Gateway : 10.10.1.1. Do you wish to apply your new network configuration ? (y/n/q): y 10) If following messages come up on your screen with “bash# ” prompt, the new network configuration has successfully applied. Your network configuration was changed.
Network Video Server User’s Manual Bash# ifconfig eth0 Link encap:Ethernet HWaddr 00:30:6F:81:00:AE inet addr:10.10.213.22 Bcast:10.10.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6382 errors:0 dropped:0 overruns:0 frame:0 TX packets:294 errors:0 dropped:0 overruns:0 carrier:0 collisions:2 txqueuelen:100 Interrupt:9 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.
Network Video Server User’s Manual Live view & Camera Configuration Once IP assignment is finished, you can view live view through standard web browser such as MS Internet Explorer or Netscape Navigator. There are two different type of viewing option provided by FlexWATCHTM server. One is simple live view and the other is “FW-Voyager” which provides personal Network DVR(Digital Video Recording) and viewing solution. Depending on the OS and web browser, you can get different viewing option as well.
Network Video Server User’s Manual When the Client pc is not connected to Internet, you need to manually install ActiveX components in your viewing PC. - Insert the product CD in your PC - Select “FlexWATCHTM Simple Viewer control” program - Application idea ActiveX based SDK is provided for software developers so that application program developers can easily utilize digital video from FlexWATCHTM server for his own video application. 1.
Network Video Server User’s Manual screen, snapshot, PTZ control, Relay output control, Voice kit connection as well. Module Selection : Not user selectable option field. Frame rate : You can adjust display frame rate by control Frame rate option Display size : X1 for Real size, x2 for double size and Full screen mode is supported. Snap shot : You can make a snapshot of video while viewing the live video.
Network Video Server User’s Manual permission to control PTZ device. 1.4 PTZ Control. PTZ camera can easily be controlled through Control panel supported by camera web page. Not only PAN/TILT/ ZOOM function but only advanced feature such as Preset, Group, Tour and Swing, are upported. Following special features supported by the server. Easy Pan/Tilt/Zoom operation : To move camera to any direction. Camera will be moved till you release left button of mouse.
Network Video Server User’s Manual 1.4.1 PTZ configuration Preset, Group, Tour and Swing mode can be easily assigned and arranged on the liveview screen on Admin menu. Following is the step to get into configuration mode. 1) Get into Admin menu and select “Serial ports” configuration option in the Device configure section. 2) Click following sub tree to get into PTZ camera configuration mode. Serial port -> PTZ mode -> Module 0 - Camera1 3) Set up options provided by the system.
Network Video Server User’s Manual done before setting up Group and Tour mode. Also Group configuration must come earlier than Tour configuration Preset Position : Total 32 Preset Positions can be appointed on the live-view screen. Also you can give the Preset Name to each Preset Position. Group : Up to 6 Preset Positions can be formed into one Group and up to 6 different camera groups can be configured. Tour : Up to 6 Groups can be set up as a camera tour group.
Network Video Server User’s Manual 2) Control the camera toward any position where you want to pre-set. Also click the drop-down menu for choosing the Position Name. Then click ‘Set’ button. 1.5 Group set-up Once you appointed a number of Preset Positions, then they can be formed into a Group. 1) Click ’Group set’ button, below window will pop up. 45 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual Speed (1~20) : To set the camera speed while it’s running from one position to another. Recommended speed is about 10 for appropriate operation. Time (1~20) : To set the camera dwelling time between the preset position when the group mode is enabled. The time unit takes about 3 seconds. Thus, if we select 2 in the time setting PTZ will stay about 6 seconds. 2) Choose ‘Group No.’ and click ‘Start Set’. 3) Set ‘Speed & Time’ and select the first position No.
Network Video Server User’s Manual 2) Click ‘Start set’ and select group No. from among you arranged at Group set-up. 3) After setting in order up to 6 Groups, then click ‘Save Set’ and ‘Close’ button. 1.7 Swing set-up You can appoint a number of Preset Positions on the live-view screen before setting the Preset name, or vice versa. Also they can be re-assigned if you need. 1) If you click ’Swing set’ button, then below live-view screen will pop up.
Network Video Server User’s Manual You can play Swing mode by clicking buttons on PTZ Control Panel at Live View. 2 FW-Voyager based view and recording FW-Voyager is web based DVR software for personal video recording. Using this free software, user can easily install the software and do video recording at any time. Note that FW-Voyager is works on MS Internet explorer of Window OS. - Click “Voyager” tab in the web page of the server - Wait till the Voyager program is automatically downloaded.
Network Video Server User’s Manual quality setting. 3.1 Camera value string configuration Some of video related value string can be transmitted along with live video stream so that client program can receive and utilize video related value string for his own application. Default Video Format : To manually change video format.
Network Video Server User’s Manual To send video along with server name Video with IP address: To send video along with IP Address Image encryption: Image encryption is security feature. Once it is enabled, user must enter encryption code to view live video. ) Note All of video related values are encrypted in the JPEG image and can not be read by any program as it is. It is intended to help application program developer to utilize video related value string for his own specific application.
Network Video Server User’s Manual Mode. Once Image encryption is enabled, FW-Manager can not display live video. Thus, you must disable Encryption mode when the image is to be viewed from FWManager program. 3.2 Camera configuration Through camera configuration mode, you can adjust the video quality to meet your requirement.
Network Video Server User’s Manual ( Notice : If you are using 2-Byte Unicode Character, number of character is limited to 10 ) Image Size : 4 different size of video can be set up. NTSC PAL Full 704 x 480 704 x 576 Large 704 x 240 704 x 288 Normal 352 x 240 352 x 288 Small 176 x 112 176 x 144 Application Idea Full size of video can show interlaced video when the camera is displaying fast moving picture. To avoid interlaced video, use large size of video which use Field image only.
Network Video Server User’s Manual flexibly filter out motion area. 3.3.1 Setting procedure 1) Go to “Camera & Motion” option in the Admin Menu 2) Select the camera for video configuration 3) Click “Select Area” button from the Camera configuration menu 4) Click the square block to set up motion detection area 5) Adjust Motion sensitivity (the lower the number, the higher the motion sensitivity) 6) Check “Motion Enable” check box and Click “Apply” button to save your configuration 3.3.
Network Video Server User’s Manual Recording in the FW-Manager To record motion triggered image in the FW-Manager (NDVR Software) client program, you should not use Software motion detection function in the FW-Manager. - Simply configure motion detection for the selected camera in the FlexWATCHTM server - Set up Motion based recording condition in the FW-Manager (Do not set up motion detection area in the FW-Manager software). 54 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual System Configuration System configuration is to set up basic functions which help you properly run and manage the system. It is highly recommended to set up the configuration before any other configurations. Following functions are provided in the System configuration mode.
Network Video Server User’s Manual 1) Go to Date & Time setup menu in the System configuration section of Admin mode 2) Set the correct time and click “Apply” button 2.2 Date & Time using NTP server If multiple servers are installed over the network and controlled by client program and synchronized time info is required, use NTP(Network Time Protocol) option. 1) Go to [NTP setup] menu in the Network configuration section of Admin Mode 2) Type in NTP server name or use default NTP timeserver, ntp.ewha.
Network Video Server User’s Manual A. Option to allow system access without system Login ID & PW B. Channel based different user account creation C. Different control authority for Video, PTZ, Audio, and relay output device control 4.1 Full Access To allow system access by anyone who know the IP address. PTZ, Audio and Relay output device can be controlled by anyone. Thus, if security for video is important, it is highly recommended to user limited access mode below 4.
Network Video Server User’s Manual ) Note default VS Module ID is 0 and only Default VS Module ID is workable. Full Access : If full access is selected, any body can access the server and control the video. No Access : This is to temporally restrict camera access by specific user without delete user account to temporally block access to the camera. Selective Access: This is to set up control authority for the respective or all cameras.
Network Video Server User’s Manual Camera number 0 means Camera number 1. 5 Frame rate control Maximum Video frame rate which sever can transmit over the IP network can be set up through Frame rate control option. Through this maximum frame rate control option, user can limit network bandwidth consumption by video transmission. 1) Go to [Access Control] option in the system configuration menu in the Admin page. 2) Set up Maximum frame rate. Following table could be an example.
Network Video Server User’s Manual 3) Click [Apply] button 6 Tx Module Registration(NVCP) ) - Notice If you do not connect FlexWATCHTM server to NDVR server, do not set TX module configuration - Once Tx Module configuration is done, set up RX module configuration in the NDVR server as well Video proxy function is supported by NDVR server such as FW-5440 and FW-5000 server.
Network Video Server User’s Manual be set in the NDVR server. 1) Click TX Module registration menu in the System configuration mode of Admin window. 2) Type in NVCP Password in the NVCP Password configuration filed. ) Notice NVCP Password is security feature which authenticate server access by RX module (FW-5440 or 5000 NDVR server) to FlexWATCHTM server. Once NVCP Password is configured, that password must be set up in the NDVR server to get video from FlexWATCHTM server.
Network Video Server User’s Manual simultaneously work with FlexWATCHTM server. 4) Select Passive or Active Mode depends on the network situation with NDVR server. 5) Once Active mode is selected, type in IP address of NDVR server.
Network Video Server User’s Manual Network Configuration Network configuration mode provides interface for the server to be connected to broadband network or PSTN line. In addition to basic network, application port such as HTTP, NVCP, Voice port configuration and IP filtering options are provided. 1 Network configuration You can change IP address of server through LAN configuration mode. 1.1 Static IP Select this to assign static IP in the server.
Network Video Server User’s Manual Once DHCP is enabled, there is not other setting to be changed in the network works configuration except DNS info, if required. 2.1.1.1 IP notification by E-mail service You can receive IP address of the server through e-mail from the server, when the server is connected to DHCP server. Please do not enable DHCP client feature till you open a way to receive or get IP address of server. 1) Check whether you are in the DHCP environment before starting set-up.
Network Video Server User’s Manual configuration in Advanced Service 2.1.1.1 Server access through AOIP server Once Server is registered in the AOIP server and DHCP is enabled, you can access the server through AOIP server. IP address of server can be found from AOIP server as well. In this case you do not need to configure e-mail address setting to get IP address from the server.
Network Video Server User’s Manual connection. ) Note Once PPPoE is enabled, LAN network setting will be disabled. 3 Network port configuration HTTP port, NVCP and VDCP ports are application port through which video and audio data can be transmitted over the TCP/IP network. 3.1 HTTP port configuration When you need to change Default HTTP Port (#80) to other port, you can change HTTP port. This is very useful when more than one server should be installed behind a router.
Network Video Server User’s Manual 3.3 VDCP Port configuration VDCP port is UDP port for Voice Communication. By changing VDCP port (Default number is 32001), you can install more than one Voice kit and Video server under the router. Note that when Voice Kit is connected to Internet, respective UDP port of the router must be opened.
Network Video Server User’s Manual Dial-in is to allow server connection from remote client. This option is useful for the user to connect the server at any time. Especially when the server sends e-mail notification for the alarm and user want to check the situation. 4.2.2 Application with Dial-out Server can establish the Internet connection through PSTN line and send FTP or e-mail when the alarm condition is triggered by any event.
Network Video Server User’s Manual PPP Client : This means that FlexWATCHTM server act as client and call out to ISP.\ PPP Server : This means that FlexWATCHTM server acts as a Server and receives a call from remote user. Tel#, User ID and User password : ISP phone number and user account for Internet connection to ISP. Default Route : Enable this option. When Dial-out option is selected. ) Note If you use external modem, we recommend ‘3COM U.S.
Network Video Server User’s Manual modem, GSM or GPRS Modem or any type of wireless modem. This mode is not for general users. Thus, if you need to connect special modem device, please contact your vendor or manufacturer for more information, sales@flexwatch.com 4.4 Dial-in Configuration Dial-in is to allow client PC to call into the server and get live video through PSTN line. Overall configuration is very similar to that of Dial-out configuration. But much more simple than Dial-out.
Network Video Server User’s Manual browser of the FlexWATCHTM server. Local IP address and Remote IP address is virtual IP address which is used at the time of Modem connection only Local IP address : System default IP address (192.168.2.1) resides in the FlexWATCHTM server for modem connection only. So when you connect the FlexWATCHTM server from remote PC using dial-up networking and physical connection is made, you need to run your web browser and enter this system default IP address(192.168.2.
Network Video Server User’s Manual LAN : This is default path the send any data to outside. Modem : when PSTN or other medium than LAN is used to send data to outside. This service port must be checked when any data is to be sent through PSTN or other medium than LAN which is connected to COM port. ) Note Service path must be set up and checked before starting WAN configuration to send any data through external PSTN modem connection or equivalent If LAN is to be used, select “None(LAN)” option.
Network Video Server - User’s Manual Once things are set up, you can login to AOIP server and connect your FlexWATCH™ server. ) Note AOIP is proprietary data service run by FlexWATCH™ or its business partners around the world. Thus, depending on the country AOIP service can run by your local vendor or master distributor or in some case, you need to user AOIP server run by manufacturer. More detailed information about how to use can be acquired by contact your local distributor or sales@flexwatch.com .
Network Video Server User’s Manual NVCP-Tx Port should be enabled only when video is transmitter to NDVR server such as FW-5440 and FW-5000, or Video proxy server supplied by FlexWATCHTM server. If not, do not enable this option. 7 Network Status You can see all the network status configured in the system through “Network status” option. Please Select “Network Status” menu in the Network configuration mode of Admin Window. 74 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual External Device connection & configuration External device such as Serial input device, Serial output (UART) device, Audio kit and Alarm input and output device can be connected to the system and controlled over the TCP/IP network. 1 Serial Ports Configuration Guide This chapter will guide you how to install and configure Serial-interface devices. 1.1 Hardware Description 1.1.
Network Video Server User’s Manual 2 Installation & Configuration of External Device 2.1 Console (Hyper Terminal cable connection) Console has to be connected to COM Port with RS-232 Serial cable. COM,DIO port 87654321 GND Tx 1) Connect COM1 or COM 2 Port at your PC and COM Port at FlexWATCHTM server with RS-232 Serial cable.
Network Video Server User’s Manual 7) Select the installed Serial Input Device Model on the dropdown menu as above. 8) Click ‘Apply’ button. ) Note Serial Input device protocol can separately be uploaded into the system per customer needs. User can upload serial input device protocol file which is provided by manufacturer only. This function is not for general use.
Network Video Server User’s Manual 2) Go to Admin Menu >> System Configuration >> Serial Ports Configuration. 3) Select ‘Serial Output’ at COM mode, and Click ‘Apply’ button. 4) System reboot will be recommended, then click ‘Reboot’ button. 5) After rebooting, Go to Admin Menu >> System Configuration >> Serial Ports Configuration. 6) Click “Serial Output Mode”, then following window will show up. G. After setting up the parameters in the each filed, click ‘Apply’ button.
Network Video Server User’s Manual sales@flexwatch.com. 2.3.3 UART(Universal Asynchronous Receiver Transmitter) device By-pass command mode is supported by the system so that user can send command string to target device through the server from the remote area. By-pass command string can be sent either by third party application program or control panel inside of the system. A.
Network Video Server User’s Manual 2) Connect RS-232 Serial Cable to FW-V10S. 3) Go to Admin Menu >> System Configuration >> Serial Ports Configuration. 4) Select ‘Voice’ at AUX mode, and click ‘Apply’ button. Please note that Voice kit has to be connected to COM Port (through RS-232) only. 5) System reboot will be recommended, then click ‘Reboot’ button.
Network Video Server User’s Manual 8) Click “Save” button to save your configuration. 3 Alarm input device connection FlexWATCHTM server has Alarm Sensor interface so that it can send alarm notification by activating e-mail or FTP function or activate alarm output device such as Siren or light. FlexWATCHTM server supports opto-coupled input circuit and any dry contact type of Alarm sensor can easily be interfaced to the server. Following is circuit diagram for Alarm input part.
Network Video Server User’s Manual 4.1 Alarm output device connection Any Relay contact type of output device can be interfaced with FlexWATCHTM server. Simple connect the Alarm output device to Relay output(DO) port of FlexWATCHTM server. Following is a circuit diagram for alarm output terminal. Relay Output Circuit Diagram COM,DIO port 87654321 DO DO 4.2 Manual control of Alarm output device Alarm output device can manually be controlled through simple viewer page or admin page. 4.2.
Network Video Server User’s Manual 4.2.2 Alarm output device through Admin Page Alarm output device can manually be controlled through Admin page of the system. This option is recommended when web browser based alarm output control panel is hided and administrator want to manually control Alarm output device. 1) Run Admin configuration panel 2) Click Alarm output control option in the Service configuration mode 3) Check the alarm output port and click “Apply” button 4.
Network Video Server User’s Manual 2) Click None buffering service menu and select “Alarm output” menu. 3) Check the service “Enable” option and select output port 4) Select Alarm Duration time from the drop down menu. Note Alarm Duration time is to set up Alarm active time when alarm output device is activated by any condition. 5) Go to Condition mode and set up condition to activate Alarm output device. 84 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual Advanced Service configuration Advanced service configuration is intended to provide more sophisticated functions which are required by sophisticated users. Thus, if you are not familiar with or not good at advanced features, we recommend you to read this guide carefully and consult with your local vendor to get more close information about these features.
Network Video Server User’s Manual & ftp and Alarm buffering service B. Pre alarm buffer size : Once memory allocation is done, assign Pre alarm buffer size (Pre alarm image buffer pool) to be used for e-mail, FTP and Alarm buffering services. Any pre alarm buffer for respective e-mail, ftp and Alarm buffering services can be done within Pre alarm buffer size. C.
Network Video Server User’s Manual pre alarm buffer size for respective camera can be done within this assigned memory. Note that Pre Alarm buffer for even Alarm buffering service can be done within this memory size. Thus, you need to be careful to assign memory for this service.
Network Video Server User’s Manual This is to assign pre-alarm image buffer for each camera. Once this is configured, the maximum number of pre alarm for e-mail, ftp or Alarm buffering service (Pre alarm only) can be done with this buffer size, if there is enough memory space for respective services.
Network Video Server User’s Manual Total buffer size • 3700 kb Total Pre-alarm buffer size (40%) Alarm buffering service size (60%) Total Buffer size is variable depending on the memory used by the system * Above is only for example - Total number of Pre Alarm+ Post Alarm for FTP per channel < 256 frame. - Total number of Pre + Post alarm for e-mail per channel <10 frames for channel.
Network Video Server User’s Manual 1) Go to Advance service mode in the Service configuration section 2) Go to Buffering service mode 3) Click “Buffer Calculator” button to run the calculator 4) Pre configure pre/post alarm buffer for each service. This previous window can be open till you manually disclose the Window. Thus, you can refer to this table when you configure e-mail, ftp or Alarm buffering service configuration.
Network Video Server User’s Manual Condition Setup Criteria Set up 2.1 Condition Setup This is to define basic condition to activate any option selected. Select right condition from the option provided. Always : To active any selected option regardless condition. If you select this condition Schedule and Event condition window become inactive. Schedule Only : To active any selected option by scheduling.
Network Video Server User’s Manual Event Only : To activate any selected option by Event only. Sensor status change is recognized as Event. Schedule and Event : To active any selected action when Event is triggered for the specified time period only. If Event is incurred out of Scheduled period, no action will be done. 2.2 Criteria Setup Once condition is selected, you need to set up event criteria following which any selected service will be executed.
Network Video Server User’s Manual Event number can be mapped as a Sensor port and camera number. DI Open State : This means that sensor is triggered and become open status from Normal close status. Select this when you use NC(Normal Close) type sensor. DI Close State : This means that sensor is triggered and become close status from Normal open. Select this when you use NO (Normal Open) type sensor. Motion Detection : By selecting this option, motion detection based event can be configured.
Network Video Server User’s Manual 3 e-mail configuration Schedule, event or schedule and event driven e-mail sending is supported by the server so that when there is any pre-configured event is happened, e-mail notice will be sent to any e-mail account. 3.1 e-mail function configuration Up to 10 pre/post alarm image can be appended and sent through one e-mail when the event happens. By configuring pre/post alarm for e-mail, you can decide the number of image to be sent by an e-mail.
Network Video Server User’s Manual Authentication Login: Now these days most of ISP is try to authenticate sender e-mail address due to security and spam mail issue. If sender authentication is enabled by your ISP, you need to get your login ID and Password from your e-mail service provider. Sender (E-MAIL): put the sender e-mail. If you use system default sender e-mail address, it will not work. E-mail address 1~ 3: put recipient e-mail address. Up to 3 different e-mail account can be supported.
Network Video Server User’s Manual do with Pre alarm buffer size. Note that the sum of pre and post alarm can not exceed 10 frames. Value Format : Value strings can be sent together with e-mails. Please click “ ” mark in the admin page to get more information. 3.2 e-Mail condition set up Up to 3 different e-mail conditions can be set up for each camera. Schedule, event or schedule & event driven e-mail condition can be set up to send e-mail.
Network Video Server User’s Manual is slightly different. 4.1.1 Directory option for Buffered FTP Buffered FTP means that only pre/post alarm buffered image will be sent to FTP server when the ftp is triggered by the event. FTP function of FlexWATCHTM server has two different level of directory and file name option and following are details. Base Directory Name : Base directory is a path where ftped image will be saved in the FTP server.
Network Video Server User’s Manual Base File name : User defined prefix of file name of each image. File name of FTP images will automatically be concatenated after prefix( Base File name ). Directory name : Multiple directories can be created in the Base directory so that ftp image can be stored in a classified directory. Once you select Directory name filed and click “Make Directory” button, multiple subdirectories will automatically be created in the Base directory according to selected option.
Network Video Server User’s Manual This is used when some number of ftp images should be stored and refreshed as new ftp images are stored in the ftp server. By setting up Modulo number for sequence, you can limit number of image to be stored and refreshed. If you set it as 8, 8images will be stored in the FTP directory and FIFO(first come, first out) based image will be saved in the FTP server. Overwrite: This is to refresh old image with new image in the ftp server.
Network Video Server User’s Manual event and only pre/post alarm buffered image can be sent to FTP server. 1) Go to Advance Service menu in the service configuration mode and select Buffering Service option 2) Set up Pre alarm buffering configuration for FTP service 3) Set up FTP directory and file name option 4) Select the camera and set up FTP condition for each camera. Up to 3 different ftp condition can be set up for each camera. 4.2.
Network Video Server User’s Manual 5) Select the camera and assign Pre/post alarm image frames. 6) Click “Save” button to memorize your new setting in the system. 7) Click the Condition menu and set up alarm buffering service condition. 8) Click “Advance Service” menu in the Admin window and click “Stop and Apply” button to start record alarm triggered image in the system memory.
Network Video Server User’s Manual Preview Single Images: This is to view image one by one. Preview Multi images: You can view panoramic images of all the saved images at a glance. 2) Click Preview Single Imager or Preview Multi images option to playback.
Network Video Server User’s Manual program through CGI Patch. This option is to invoke third party application program upon receipt of sensor information from FlexWATCHTM server.
Network Video Server User’s Manual Utilities Utilities is to manage and control system properly. Save Configuration, Flash Update, System Reboot and system upgrade options are provided. 1 Save Configuration This is to save all new configuration and settings in the system memory. Once new configuration is saved by “Save Configuration” menu, new configuration will permanently saved in the system memory only after system Reboot or system power off 2 Reboot Reboot means restart system.
Network Video Server User’s Manual logics for system configuration, since executing this option Except Network configuration will lose all of your setting. 4 System Update System update can remotely be done through web page of the system or ftp option with telnet and Hyper Terminal mode. In this user manual only web based system update method is described and ftp based system update method can separately provided. 4.
Network Video Server User’s Manual All (kernel, RAM disk, System, Web) Update: To completely update all the system for Kernel, RAM Disk, System and Web all together except PTZ Device Driver or Sensor Device Driver. This option is recommended if there is special notice by manufacturer. Generally complete system update comes only when there is big change for all of the system software. System and Web Update: To update system and web related software together. This update can be common to update the system.
Network Video Server User’s Manual PTZ Device Driver is already built-in the system. But if there is a new PTZ Device driver supported by the system, it can separately uploaded into the system without other software change. Sensor Device Driver : Serial input device driver can separately be uploaded into the system so that independent Serial input device can work with FlexWATCHTM Server. 4.
Network Video Server User’s Manual you want to skip specific update, click “Skip” button. 4) Once update is successfully done following result will come up. 5) If you want to update RAM Disk, System and web page, please click “Next” button follow the web guide to update more files. 6) If all of file update is finished “System Reboot” window will come and do system reboot to apply new update. 108 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual 109 - INTPLUS [2005] - Seyeon Tech Co.
Network Video Server User’s Manual Warranty Product Network Video Server Model S/N FlexWATCHTM 1160 A/S Seyeon Tech Ltd. +82-2-3017-0866 2 year Limited www.flexwatch.com Warranty Seyeon Tech Co., Ltd. TEL : +82-2-3017-0855 FAX : +82-2-3017-0843 http://www.seyeon.co.kr http://www.flexwatch.com A/S Center: Tel : +82-2-3017-0855 Fax: +82-2-3017-0843 110 - INTPLUS [2005] - Seyeon Tech Co.
