SEWOO TECH CO.,LTD. Doosung BD, 689-20, Geumjeong-dong, Gunpo-si, Gyeonggi-do, 435-862, Korea TEL : +82-31-459-8200 FAX : +82-31-459-8880 www.miniprinter.com MODEL : LK-T210 Receipt Printer User’s Manual Rev. 1.
1
Table of Contents 1. Parts Identifications 1. Parts Identifications 3 2. Setting up the printer 4 2.1 Unpacking 4 2.2 Connecting the cables 5 2.3 Loading the roll paper 9 2.4 Dip switch setting 11 3. Control panel and other functions 14 3.1 Control panel 14 3.2 Error Indicating 14 4. Self Test 15 5. Hexadecimal Dump 16 6. Specifications 17 6.1. General Specifications 17 6.2. Auto Cutter Specifications 19 6.3. Interface 19 6.4. Electrical Characteristics 19 6.5.
2. Setting Up the Printer 2-1. Unpacking 2-2. Connecting the Cables Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. You can connect up the cables required for printing to the printer. They all connect to the connector panel on the back of the printer, which is shown below : The Printer User's Manual Roll Paper PERIPHERAL DRIVE CONNECTOR POWER CONNECTOR INTERFACE CONNECTOR For connection to a host computer.
2-2-1. Interface Connector Centronics Parallel Interface Serial Interface PIN 2 3 4, 20 6 1, 7 SIGNAL TXD RXD DTR DSR GND PIN 6 SIGNAL +3.
2-3. Loading the Roll Paper 2-2-2. Cash Drawer Connector The printer can operate two cash drawers with a 6 pin RJ-11 modular connector. The driver is capable of supplying a maximum current of 1.0A/24VDC for 510ms or less when not printing. Notes: Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly. (Turn off power switch) 1.
5. Be sure to note the correct direction that the paper comes off the roll. 2-4. Di p Switch Setting The printer is set up at the factory to be appropriate for almost all users. On the other hand, offers some more settings for users with special requirements. It has DIP switches that allow you to change communication setting, such as handshaking and parity check, as well as print density. Your printer has two sets of DIP switches. The functions of the switches are shown in the following tables.
♣CAUTION: ♣CAUTION: Turn off the printer while removing the DIP switch cover to prevent an electric short, which can damage the printer. When the paper is jammed with cutter, the top cover might be stuck. In this case, repeat power on and off several times. If the top cover is still stuck, please follow the steps to release the papers from jamming. 1. Make sure the printer is turned off. 2. Remove the screw from the DIP switch cover.
3. Control panel and other functions 3-1. Control panel You can control the basic paper feeding operations of the printer with the button on the control panel. The indicator lights help you to monitor the printer’s status. Control Panel 4. Self Test The self-test lets you know if your printer is operating properly. It checks the control circuits, printer mechanisms, print quality, ROM version and DIP switch settings. This test is independent of any other equipment or software. Running the self test 1.
5. Hexadecimal Dump This feature allows experienced users to see exactly what data is coming to the printer. This can be useful in finding software problems. When you turn on the hex dump function, the printer prints all commands and other data in hexadecimal format along with a guide section to help you find specific commands. To use the hex dump feature, follow these steps 1. After you make sure that the printer is off and Dip s/w 1-2 is ON, turn on the printer. 2.
(8) Overall dimension 6-2. Auto Cutter Specifications (1) Cutting Frequency Max. 30 cuts per minute (2) Thickness of paper 0.06 ~ 0.09 mm (3) Cutter Life 1.5 million cuttings 6-3. Interface RS232C Serial Interface, Centronics Parallel Interface(IEEE1284), USB Interface USB COMBO Interface, Ethernet Interface(10Mbps), Wi-fi(802.11b) 6-4. Electrical Characteristics 18 (1) Input Voltage DC 24V ± 10% (2) Current Consumption (3) Power Connector Operating: Approx. 1.
7. Command List ♣Important! When connecting or disconnecting the power supply from the printer, be sure that the following cautions are observed. (1) Use a power supply (Limited Power Supply) of DC 24V±10% and more than 2.5A. (2) Be careful about installing the printer in an area where there is noise. (3) Take the appropriate measure to protect against electrostatic AC line noise, etc. 6-5.
No.
