Test Report No.
15" TFT LCD TV/MONITOR Owner’s Manual Model: LT-15KMF
Warnings WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN. WARNING : To reduce the risk of electric shock do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons..
IMPORTANT SAFETY INSTRUCTIONS IMPORTANT SAFETY INSTRUCTIONS Important safeguards for you and your new product Your product has been manufactured and tested with your safety in mind. However, improper use can result in potential electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.
IMPORTANT SAFETY INSTRUCTIONS 14. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.
Contents Before operating the set, please read this manual carefully.
Supplied Accessories L Make Sure the following accessories are provided with Product. 1. AC/DC adaptor 2. AC Cord 3. Remote controller 4. Batteries (type AAA) MENU TV/AV SLEEP Q.VIEW ST/SAP LIST CH CH PSM SSM ARC/ * PC/ * CC 15" TFT LCD TV/MONITOR 5. Owner’s manual Owner’s Manual Model: LT-15KMF 7. PC Audio IN cable 6 6.
Co ntro ls 1. M E NU Dis plays a menu. 2. + C H - (P rogram Up/Down) S elects a program or a menu item. 3. P ower Indic ator Illuminates in red when the TV is in s tandby mode./ Illuminates in green when the TV is s witched on. Illuminates in blinked when the power s ave mode(only P C mode). 4. ON/OF F S witches TV s et on or off. 5. R emote c ontrol s ens or Accepts the IR s ignal of remote controller. 6. + VOL - (Volume Up/Down) Adjusts the volume./ Adjusts menu settings. 7.
Controls All the functions can be controlled with the remote controller. Some functions can also be adjusted with the buttons on the front panel of the set. Remote controller Before you use the remote controller, please install the batteries. 1. POWER Turns the TV on from standby ro off to standby mode. 2. MUTE 1 2 Turns the sound on and off. 3. NUMBER buttons Selects program numbers. 4. MENU Displays a main menu. 3 4 5 TV/AV 5.
Controls 12. VOLÏq (Volume Up/Down) Adjusts the sound level. Adjusts menu settings. 13. PSM (Picture Status Memory) Recalls your preferred picture setting 14. SSM (Sound Status Memory) Recalls your preferred sound setting 15. PC/* Selects the PC mode. TV/AV MENU 16. CC Sets the caption function section. SLEEP Q.VIEW ST/SAP LIST CH CH Battery installation PSM 13 uInserting batteries 1. Remove the battery cover by pulling it upward in the direction shown by the arrow. 2.
Basic Operation Turning the TV On and Off Standby Setup: The AC-DC adapter and the AC power cord must be set up and connected to have the TV in standby mode ready to be turned on. Press the ON/OFF button on the front panel of the TV to go into standby mode. 1. If the TV is in standby mode, press the Power button on the remote controller or the TV itself to turn the TV on. 2. Press the Power button again on the remote controller or the ON/OFF button the TV itself to turn the TV off.
On Screen Menus and Displays 1. Press the MENU button to display main menu. 2. Press the CH xy button to select menus-Picture, Sound, Special, Setup. 3. Adjust each menu with the VOLÏq button. 4. Press the MENU button to return to preceding menu. 5. Press the TV/AV button to finish adjusting menu. Picture MENU Ș Ș Ș Ș Picture Sound Special Setup Position ƇƉ Next ȖȘ Exit TV/AV Contrast Brightness Colour Sharpness Position ƇƉ Back MENU Equalizer Flat Music Movie Speech User 0.1 0.5 1.5 5.
Setting up TV Program Once you have preset the programs, you will be able to use the CHxy or NUMBER buttons to scan the programs you programd. Programs can be tuned using automatic or manual modes. Auto program All programs that can be received are stored by this method. It is recommended that you use Auto program during installation of this set. 1. Press the MENU button. 2. Select the Setup menu. 3. Select the Auto program menu. 4. Press the CHxy button to select System. 5.
Setting up TV Program Manual program Manual Program lets you manually tune and arrange the programs in whatever order you desire. Also you can assign a program name with 3 characters to each program number. 1. Press the MENU button. 2. Select the Setup menu. 3. Select Manual program menu. 4. Select a program with the VOLÏq button. 5. Press the CHxy button to select Channel menu. 6. Press the VOLÏq button or directly number button to select a Channel. 7. Press the CHxy button to select the Table menu. 8.
Parental Control If used, this optional feature can "block" undesirable programs from appearing on the TV. Parental Control offers the user a wide variety of options and settings that restrict or "block" the programming that can appear on the TV. Parental control allows the user the capability of defining which program rating is acceptable, to the younger or more sensitive viewer. It can be preset and turned either on or off by the user who specifies the secret 4-digit code, the password.
Parental Control 1. Press the MENU button. 2. Select the Setup menu 3. Select the Parental Control menu. 4. Press the CHxy button to select. 5. Adjust each item with VOLÏq button Parental Control Movie rating MPAA Ect. Sources Block Hour Password Parental Lock Position ƇƉ Back MENU Parental Control Ș Unblock Unblock 00 Hours To SetȖȘ Off Adjust ȖȘ Exit TV/AV Parental Control Selected Item MPAA Ect.
Parental Control INFORMATION MOTION PICTURE ASSOCIATION OF USA (MPAA) RATING SYSTEM Grade Meaning G General Audiences Content not offensive to most viewers Parental Guidance Content is such that parents may not want their PG children to view the program. Suggested Parental Guidance Program is inappropriate for preteens, with a greater degree of offensive material Suggested than a PG PG-13 Suggested rated program R Restricted viewing NC-17 Restricted Viewing Not for children under age 17.
Captions The captions is a process which converts the audio portion of a television program into written words which then appear on the television screen in a form similar to subtitles. Closed captions allow viewers to read the dialogue and narration of television programs. Using Closed Captions Captions are the subtitles of the dialogue and narration of Shooting... Goal in..... television programs. For prerecorded programs, program dialogue can be arranged into captions in advance.
Picture Control You can adjust picture Contrast, Brightness, Colour, Sharpness and Tint(only in NTSC mode) to the levels you prefer. Picture Manual Picture Control 1. Press the MENU button. 2. Select the Picture menu. 3. Press the CHxy button select a picture item. 4. Press the VOLÏq button to adjust the picture condition as you want. 5. Press the TV/AV button to store for the picture User.
Sound Control You can select your preferred sound setting; Flat, Music, Movie or Speech and you can also adjust the sound frequency of equalizer, balance. If you switch AVL to on, the set automatically keeps on an equal volume level even if you change programs. 1. Press the MENU button. 2. Select the Sound menu. 3. Press the CHxy button to select the desired sound item; Equalizer, Balance, AVL, Surround or Sound Mode. 4. Press the VOLÏq button to make desired adjustment. 5.
Sound Control Auto Sound Control * The sound Flat, Music, Movie and Speech are programd for good sound reproduction at the factory and cannot be changed. SSM (Sound Status Memory) 1. Press the SSM button. 2. Press the SSM button repeatedly to select. Each press of the button changes the screen display as below.
Other functions You can control other functions; Clock, Blue Back, Auto Sleep, Childlock, Radio menu. Special Clock Clock Blue Back Auto Sleep Childlock Radio Setting the clock is necessary in order to use the various timer features of the TV. You can set automatic TV On or Off time. 1. Press the MENU button. 2. Press the CHxy button to select the Special menu. Then press the VOLÏq button. 3. Press the VOLÏq button to select Clock menu.
Other functions Blue back If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must select the Blue back On.(Pressing the VOL button will alternate between “On” and “Off”. Auto sleep If you select Auto sleep On the set will automatically switch itself to standby mode approximately ten minutes after a TV Channel stops broadcasting. 1. Press the MENU button. 2.
Radio Control This function is possible only when the set is in Radio mode.(Radio mode is displayed when the Setting for special menu is radio On.) 1. Use TV/AV button on remote controller to select Radio mode. 2. Press the MENU button to set Radio Setup menu. 3. Press the VOL button repeatedly to select Mode Auto or Manual. 4. Press the CH button select Frequency. Then press the VOL button repeatedly to tune in the desired station manually. 5. Press the CH button to select Program.
External Equipment Connection You can connect additional equipment, such as VCRs, camcorders etc. to your set. Examples are shown below. Antenna connection 1. Connect RF out on the VCR to the Antenna input on the rear of the TV. 2. Connect the antenna cable to the antenna in jackon the VCR. 3. Press the TV/AV button to select Antenna Input source. 4. Press the PLAY button on the VCR. ANT. DC12V IN VCR COMPONENT INPUT 1. Connect the Video outputs (Y Cb Cr) on a DVD to the COMPONENT on the TV. 2.
External Equipment Connection S-VIDEO INPUT If using an S-VIDEO source, the picture quality will be improved over a video source. 1. Connect the S-VIDEO output of a VCR to the S-VIDEO input on the TV. 2. Connect the audio cables from the S-VIDEO VCR to the L (MONO), R inputs on the TV. 3. Select S-VIDEO mode by pressing the TV/AV button repeatedly. 4. Press the PLAY button on the VCR. The VCR playback picture appears on the screen.
Connecting PC as monitor This function is possible only when the set is in PC mode. Use the TV/AV button on remote controller. Picture adjustment You can adjust picture Contrast, Brightness, Temperature, Clock, Phase, ARC as you prefer. 1. Press the TV/AV button to select the PC mode. 2. Press the MENU button. 3. Select the Picture. 4. Press the CHxy button to select the desired picture item. 5. Press the VOLÏq button to make appropriate adjustments. 6. Press the TV/AV button to exit menu.
Connecting PC as monitor Sound adjustment 1. Press the MENU button. 2. Select the Sound menu. 3. Press the CHxy button to select the desired sound item; Equalizer, Balance, AVL, Surround or Sound Mode. 4. Press the VOLIq button to make desired adjustment. 5. Press the VOLq button in Equalizer to set the Equalizer. 6. Press the CHxy button to select your preferred setting ; Flat, Music, Movie, Speech or User. To set the Equalizer User. a. Select User by pressing the CHxy button. b.
Connecting PC as monitor Position Adjustment This function is to adjust picture to left/right and up/down as you prefer. 1. Press the MENU button. 2. Select the Position menu. 3. Press the CHxy button to select the desired position item. 4. Press the VOLÏq button to adjust horizontal position and vertical position. 5. Press the TV/AV button to exit menu Position H-Position V-Position Position ƇƉ Back MENU -61 -12 Adjust ȖȘ Exit TV/AV Setup You can select the desired language in PC mode. 1.
Connecting PC as monitor PC/DTV INPUT 1. Connect the PC IN cable (D sub jack) from the monitor output socket of the PC to the PC/DTV input socket of the set. 2. Connect the PC Audio IN cable from the PC to the PC AUDIO IN of the set. 3. Press the TV/AV or PC button to select PC mode. 4. Switch on the PC, and the PC screen appears on the set. The set can be operated as the PC monitor.
Product Spec. Horizontal size 390 mm Thickness 60 mm Height 350 mm Weight 6.2 kg Main body Power requirements Television system Television channels Display panel DC 12V/3.0A NTSC VHF: 2~13 UHF :14~69 Cable : 01~125 15.1” TFT-LCD Power consumption 45W External antenna impedance 751 Audio output 30 1.5W + 1.5W External input ports •DC 12V IN • Headphone jack • AV-IN AC Power Adaptor AC 100-240V, 50/60Hz • S-VIDEO IN • COMPONENT IN • PC AUDIO IN • Antenna IN • PC/DTV IN Output:12Vdc, 3.
Troubleshooting Problem Check item No picture on screen and no sound from speakers • Insert the AC power cord plug securely in AC power outlet. • Make sure the remote control is not in the standby mode (The POWER/Standby indicator is red.) No picture/No picture from AV terminal • Check the brightness setting of the display. • Lamp may have malfunction. • Make sure a cable with no VIDEO input signal is connected to the S-VIDEO INPUT terminal. Picture is displayed, but no sound from the speakers.
