Cut Sheet

Phone: [phone] • Fax: [phone] • setra.com © Setra Systems, Inc. All rights reserved. The Setra Systems name and logo are registered trademarks of Setra Systems, Inc.
Model 206
Industrial Pressure Transducer
SSP206 REV L 8/2015
DIMENSIONS GENERAL SPECIFICATIONS
ORDERING INFORMATION
PROOF PRESSURE
Note: Setra quality standards are based on ANSI-Z540-1. The calibration of this product is NIST traceable.
PSIG RANGES
Gauge
Pressure
Proof
Pressure
Burst
Pressure
0-25 100 500
0-50 150 750
0-100 300 1,000
0-250 500 2,000
0-500 1,000 3,000
0-1,000 2,000 5,000
0-3,000 4,500 7,500
0-5,000 7,500 10,000
0-10,000 12,500 20,000
BAR RANGES
Gauge
Pressure
Proof
Pressure
Burst
Pressure
1.6 6 32
4.0 10 50
6.0 18 60
10 30 80
16 32 130
25 50 170
40 80 240
60 120 300
100 200 400
160 250 500
250 380 550
400 600 800
700 800 1,350
Performance Data Physical Description
Accuracy RSS
1
(at constant temperature)
±0.13% FS Pressure Fittings See Ordering Information
Non-Linearity, (BFSL)
25 PSIG range
2
±0.1% FS
±0.2% FS
Vent Through cable or terminal
Hysteresis 0.08% FS Electrical Connection 2 ft. multiconductor cable
Non-Repeatability 0.02% FS Case Stainless Steel
Response Time 5 milliseconds Zero/Span Adjustments Top External Access
Long Term Stability 0.5% FS/1 YR Weight (approx.) 6 oz
Thermal Eects Electrical Data (Voltage)
Compensated Range -4 to +176°F (-20 to +80ºC) Excitation/Output 12 to 28 VDC
Reverse Excitation Protected
Zero Shift ±1% FS/100
o
F (±0.9% FS/50
o
C) Power Consumption <0.15 watts
(approx. 5mA @24VDC)
Span Shift ±1.5% FS/100
o
F (±1.4% FS/50
o
C) Output
8
0.1 to 5.1 VDC
9
Pressure Media
Output Impedance 100 ohms
Gases or liquids compatible with 17-4 PH Stainless Steel.
3
Circuit 3-Wire (Exc, Out, Com)
Environmental Data
Vibration
11
200g Operating
Temperature
Electrical Data (Current)
Operating
4
-40 to +185°F (-40 to +85ºC) Circuit 2-Wire
Storage -40 to +185°F (-40 to +85ºC) Output
10
4 to 20 mA
11
Acceleration 10g Maximum
5
External Load 0 to 800 ohms
Shock
6
200g Operating Min. Supply Voltage (VDC) = 9 +0.02 x (Resistance of receiver
plus line)
Vibration
7
20g 50-2000 Hz
1
RSS of Non-Linearity, Non-Repeatability and Hysteresis
2
25 PSIG range accuracy is ±0.22% of Full Scale output
3
Hydrogen not recommended for use with 17-4 PH stainless steel.
4
The high temperature limit of the cable is 200ºF (95ºC)
5
Shift in output reading <0.05 psi/g typical; pressure port axis only
6
Mil-Std. 202, Method 213B, Cond. C
7
Mil-Std. 202, Method 204, Cond. C
8
Calibrated into a 50K ohm load, operable into a 5000 ohm load or greater
9
Zero output factory set to w/in ±25mV. Span (FS) output factory set to w/in ±50mV.
10
Calibrated at factory with a 24VDC loop supply voltage and 250ohm load.
11
Zero output factory set to w/in ±0.08mA. Span (FS) output factory set to w/in
±0.16mA.
Specications subject to change without notice.
Max. Supply Voltage (VDC) = 30 + 0.004 x (Resistance of
receiver plus line)
2 0 6 1
Ordering Example: 2061025PG2M11048CN - Model 206, 0 to 25 PSIG, Gauge pressure, 1/4” NPT Male tting, 4 to 20 mA output, 4’ Cable Length, ±0.13% FS Accuracy, 11 Point Cal Cert Option.
Model Pressure Range Pressure Type Fitting Output Termination Accuracy Options
2
2061= Model 206 025P 0 to 25 PSI 1R6B 0 to 1.6 Bar G Gauge 2M 1/4” NPT Male 11 4 to 20 mA
02 2 ft Cable 8 ±0.13% FS
NN None
050P 0 to 50 PSI 004B 0 to 4 Bar C Compound 1M 1/8” NPT Male
22
0.1 - 5.1 VDC
06 6 ft Cable C
11 Point Cal Cert
100P 0 to 100 PSI 006B 0 to 6 Bar J7 7/16” SAE
27
1 to 5 VDC
10 10 ft Cable D
Mate with Datum
200P 0 to 200 PSI 010B 0 to 10 Bar
28
1 to 6 VDC
25 25 ft Cable
F NEMA 4 Enclosure
3
250P 0 to 250 PSI 016B 0 to 16 Bar
2T
0.1 to 10.1 VDC
XX Special Cable Length (0-25’)
G Mating Hirshmann Con.
500P 0 to 500 PSI 025B 0 to 25 Bar
H1 Hirshmann
L Etched SS Tags
10CP 0 to 1,000 PSI 040B 0 to 40 Bar
A3 1/2” Conduit w/ 2’ Cable
Y Clean For Oxygen
30CP 0 to 3,000 PSI 060B 0 to 60 Bar
AD 1/2” Conduit w/ 6’ Cable
50CP 0 to 5,000 PSI 100B 0 to 100 Bar AE 1/2” Conduit w/ 10’ Cable
10KP
1
0 to 10,000 PSI 160B 0 to 160 Bar AF 1/2” Conduit w/ 20’ Cable
250B 0 to 250 Bar AG 1/2” Conduit w/ 25’ Cable
400B 0 to 400 Bar T1 Terminal Strip
4
700B
1
0 to 700 Bar
1
Units higher than 5k PSI are only available with a 1/4” NPT male tting
2
Both boxes must lled in alphabetical order:
• If No options: N + N
• If 1 option: Option Code + N
• If 2 options: Option Code + Option Code
3
Only available with T1 termination
4
Formerly Model 207
IN
MM
206
19/32
ACROSS FLATS
3/4" HEX
1/4"-18 NPT
PRESSURE PORT
SPAN
ZERO
0.75
19.1
0.50
12.7
ø2.00
ø50.8
ø0.44
ø11.1
2.13
54.0
2.00
50.8
Cable Version
206
Terminal Version
ZERO
SPAN
1.81
45.9
0.83
20.6
0.77
19.6
RADIUS
Current Version Shown
3/4" HEX
1/4"-18NPT
PRESSURE PORT
0.50
12.7
0.80
20.3
2.53
64.3
2.00
50.8
2.00 DIA.
TERMINAL
STRIP