OWNER’S MANUAL TEAMBMPRO.
POWERING YOUR ADVENTURES With over 50 years’ experience in power solutions combined with manufacturing and design facilities in Melbourne, Australia, BMPRO are the leading experts in RV power and control management. Inspired by the great outdoors, we have created a range of rugged, smart and reliable products to power your adventures.
SAFETY PRECAUTIONS Please read the Safety Precautions before installing or using the system. Be sure to observe all precautions without fail. Failure to observe these instructions properly may result in personal damage, or personal injury which depending on the circumstances may be serious and cause loss of life. WARNING Correct installation is the most critical factor in ensuring the safe use of the system.
INFORMATION FOR THE USER This device complies with Part 15 of the FCC Rules, and Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including what may have cause undesired operation.
CONTENTS SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . 4 INFORMATION FOR THE USER . . . . . . . . . . . . . . . . . . . 5 ABOUT THE SYSTEM . . . . . . . . . . . . . . . . . . . . . . . 8 SMARTCONNECT . . . . . . . . . . . . . . . . . . . . . . . . 10 DESCRIPTION OF PARTS . . . . . . . . . . . . . . . . . . . . . 11 DISPLAY (MODEL DEPENDENT) .
SOLAR CONTROLLER . . . . . . . . . . . . . . . . . . . . . . . 37 SOLAR CONTROLLER SETTINGS . . . . . . . . . . . . . . . . . . 38 GENERAL SETTINGS . . . . . . . . . . . . . . . . . . . . . . . 40 UNIT CONVERSION . . . . . . . . . . . . . . . . . . . . . . . 41 DIAGNOSTICS . . . . . . . . . . . . . . . . . . . . . . . . .
ABOUT THE SYSTEM The system brings smart home technology to your RV, taking control and management of your RV features to new horizons! FIGURE 1: System Diagram 8
Node The heart of the system, the Node, is an RV management system that powers and monitors your RV features and accessories. The Node communicates via RV-C to the Display or Controller (depending on your model) and Bluetooth Low Energy with your smartphone, to receive the commands to control power to all your RV features and accessories. Firmware Updates The Node can be updated over-the-air, meaning you get the latest feature updates without the need to bring your RV to your local RV dealer.
SMARTCONNECT Your system is SmartConnect ready! With SmartConnect Bluetooth sensors, you can remotely monitor various aspects of your RV, such as tire pressure, propane tank levels and individual temperatures. Through the App these sensors are a great addition to enhance your overall experience. SmartConnect sensors are available through your local RV dealership. For more details, refer to teambmpro.
DESCRIPTION OF PARTS DISPLAY (MODEL DEPENDENT) 1 3 2 4 MAIN A/C WATER PUMP INTERIOR & EXTERIOR ALL EXTERIOR LIGHTS ALL INTERIOR LIGHTS 5 FIGURE 3: The Display 1. Page Navigation Button Move between function screens, eg. From Tanks to Water screen. 2. Menu Navigation Button Navigate between items within a page, e.g. in the Water page move from Pump to Elec Heater. 3-4. Action Buttons The function for each of the action buttons changes depending on the selected menu item.
DISPLAY NAVIGATION (MODEL DEPENDENT) Use the Page Navigation Button to move from page to page. Use the Menu Navigation Button to move between menu items within a page. Tanks FIGURE 4: Tanks Screen The Tanks display shows the levels of fresh, gray and black water tanks. Levels are displayed as: FULL 2/3 FULL 1/3 FULL EMPTY Water From the Water screen, the Pump, the Electric and Gas Heaters can be switched on and off. A warning will appear if the Gas Heater fails to ignite after three attempts.
If Furnace Mode is selected, the AC-Fan option displays. AC-Fan: Settings: OFF / LOW FIGURE 8: Climate Screen with AC-Fan Energy ON: Press and hold the ON action button, until the generator turns on. OFF: Press and hold the OFF action button, until the generator turns off. FIGURE 9: Energy Screen NOTE: A generator warning will appear if the generator fault LED is actively blinking. Settings FIGURE 10: Settings Screen Pair Device: Press OK to pair to a device.
CONTROLLER (MODEL DEPENDENT) 2 1 3 4 5 7 6 8 9 10 11 12 13 FIGURE 12: The Controller 1. Controller Home Screen Button 2. Connection Bar When connected to Bluetooth, the icon will appear on screen. When connected to the cloud, the icon will appear on screen. Both icons will appear when both services are available. 3. Settings Icon Access to the App General Settings. This button is only available on the Home Screen. 4. Return Navigate to the previous page. 5.
9. Lights Turn lights and water pumps on/off: All Interior Lights All Exterior Lights All Lights or Water Pump Control 10. Motor Operation To extend (EXT) and retract (RET) any motors installed in the RV. NOTE: These buttons are also used during the pairing process between the Node and devices such as the Controller and smartphone. 11. & 13. Navigation Buttons Use navigation buttons to scroll through the Control Panel menu functions.
CONTROL PANEL MENU FUNCTIONS (MODEL DEPENDENT) The menu functions on the Controller’s Control Panel allow you to operate various motors, quickly switch off loads and pair or clear the Node. The following functions apply depending on what is available in your RV. Awnings Jacks Navigate to the desired awning: A1 (Awning 1) A2 (Awning 2) then press EXT or RET to operate. Navigate to the desired Jack: J1 (Landing Jack) J2 (Front Stabilizing Jack) J3 (Rear Stabilizing Jack) then press EXT or RET to operate.
PAIRING TO THE NODE PAIRING TO THE NODE WITH A DISPLAY (MODEL DEPENDENT) Pairing your smartphone to the Node is simple. The App will guide you through the process. The Node can be paired to a total of four devices. 1. Launch the App on your phone and choose the device installed in your RV 2. Press the Page Navigation Button to navigate to the ‘Settings’ page 3. When “Pair Device” is highlighted, press the OK function button and your smartphone will begin pairing to the Node.
PAIRING TO THE NODE WITH A CONTROLLER (MODEL DEPENDENT) Pairing your Controller, smartphone or tablet to the Node is done in three easy steps. The App will guide you through the pairing process. NOTE: The Controller will have been paired to your Node at the factory. You should only need to pair your own device or smartphone to the Node. While the Node can be paired to a total of four devices (including the Controller), you can only pair one device at a time to the Node. 1. Launch the App on your phone. 2.
4. When pairing is successful, you will be taken to the App home screen and the Bluetooth icon will be visible. FIGURE 16: Pairing Successful CONGRATULATIONS, YOU’RE CONNECTED! For additional support, refer to the FAQs and Troubleshooting section. Cannot Pair to the Node If you are pairing a mobile device to the Node and "--" appears on screen, it is mostly likely that four devices are connected to the Node simultaneously.
BMPRO CLOUD (MODEL DEPENDENT) WARNING You can only connect to the BMPRO Cloud if your RV is equipped with a Controller. Systems with a Controller have cloud control, which allows you to remotely connect, monitor and control your RV from your smart device. CONNECTING TO THE BMPRO CLOUD To connect to the BMPRO Cloud for the first time: 1. Connect your Controller to the Internet via Wi-Fi. 2. Launch the App. 3. 4. 5. 6. From the App home screen, press the Settings icon. Press Remote Connection.
CLOUD CONTROL To control the RV from cloud: 1. Launch the App on your smart device. 2. Select Log in to BMPRO Cloud, or in General Settings, select Remote Connection. 3. Enter your email address and password. Use cloud control to remotely monitor and control features in your RV. For your safety and for the prevention of unintentional damage, the leveling, motor controls and the water pump ON switch can not be controlled from the cloud.
Internet Preferences You can select from the following options: 9 4G: Connect to a 4G network. SIM card required. 9 WiFi: Connect to an external WiFi network. 9 Internet OFF: No internet source selected. FIGURE 20: Winegard Internet Preferences Winegard Status The current status of the Winegard is displayed on the Winegard tile in the General Settings area. 9 SETUP: This is seen when no Winegard network has been connected previously. Press the tile to connect to a Winegard network.
WiFi Properties To log in to a WiFi network: 1. Press the Search button for a list of available networks and select desired network. 2. If your network is not seen, make sure the Winegard is turned on and scan again. After the network name and password are entered correctly, press Done. FIGURE 21: Logging into WiFi Save and/or forget WiFi Network After the WiFi credentials are entered, the WiFi network will be saved. 9 Press Done to connect last saved network. 9 Press X to delete the saved network.
THE APP Download the JAYCOMMAND/TravelLINK powered by BMPRO app to your smartphone or tablet and enjoy the freedom to monitor and control the onboard features of your RV remotely. If your system has a Display, the App allows you to access more features of your connected RV that otherwise may not be available. WARNING Available features on the App may vary depending on your RV model. COMPATIBLE DEVICES The App is compatible with Android 6.0 or later and iOS 11 or later.
TANKS SCREEN You can control the water pump, electric, gas heaters and tank heaters from the Tanks screen, if applicable. The Tanks screen displays the levels of your fresh, gray and black water tanks. The water levels displayed are: Empty, 1/3, 2/3 and Full.
LEVELING AND MOTORS SCREENS The Leveling and Motors Screens control the Slide-outs, Awnings, Landing Legs and Jacks. It contains controls for certain Leveling Systems installed in the RV. NOTE: All Jayco-approved leveling systems are compatible. WARNING Before operating any motors, ensure the area is free from obstacles and other hazards. Please ensure that any persons near the RV are not in any danger from moving parts.
Zero Point Calibration (Model Dependent) If your model supports zero point leveling, you can calibrate perfrom zero point calibration from the Motor Settings screen in the Settings menu. FIGURE 28: Zero Point Leveling For more information on zero point calibration, refer to the Zero Point Calibration Sequence help guide. FIGURE 29: Zero Point Calibration Sequence help guide QR code Note: Depending on the type of leveling system installed, the tongue jack may not be available.
Motor Control Only one motor may be operated at a time. Once a motor is in operation, motor control will be disabled in any other device running the App. This does not include the leveling system. FIGURE 31: Motors Screen To operate motors on your own device, swipe to unlock the Motors screen.
Motor Lockout Feature (Model Dependent) WARNING The motor lockout feature is only available if your RV is equipped with a Controller. Systems with a Controller will automatically lockout the motor if a high input is detected on the brakes. This will be shown on the Node at pin 64. The motor cannot be turned back on until the lockout is disabled. If the motor is locked, the App will show a pop-up.
CLIMATE SCREEN The Climate Screen allows you to control the temperature inside your RV. The zones that appear depend on the vehicle configuration. FIGURE 34: Climate Screen Cool & Cool Auto Cool will run the fan continuously and cycle the compressor, as it needs to achieve the target temperature. Cool Auto is similar, but will only turn on the fan when the compressor is operating. There may be a three minute delay in turning the compressor on.
Fan The fan can be operated for air circulation in each zone. FIGURE 36: Fan Mode Heat If available, the RV may be heated from the furnace, heat pump or a combination of both. The furnace can only be controlled from the Main Climate Zone. To set the temperature: 1. Turn climate on. 2. Select your mode of operation. 3. Adjust the temperature to your desired setting (if available in the selected mode). 4. If the mode is set to Furnace, you can then set the main A/C fan to off or low.
LIGHTS SCREEN Lights can be turned on and off from the light screen. Brightness can also be adjusted on certain lights.
ENERGY CENTER BATTERY MONITORING Battery Monitoring allows you to monitor RV and/or chassis voltages. If no RV and chassis batteries are connected, the App will monitor the system voltage of the Node. If the voltage drops below 12V, a warning will appear on the screen. FIGURE 39: Energy Center Display GENERATOR To turn on the generator, press and hold the start generator button until the generator starts. The App will also show the running status of the generator.
AUTOMATIC GENERATOR START You can keep your battery and climate levels steady by using Automatic Generator Start (AGS). AGS will keep your levels steady by automatically turning your generator on or off. To use AGS, you may need to update the App on your smartphone. If AGS is enabled, the App will attempt to start the generator a total of four times to try and keep levels steady. If there are four failed starts, the App will stop attempting to start the generator.
ENERGY CENTER SETTINGS The Energy Center Settings are used to set the parameters to control AGS usage. To access Energy Center Settings: 1. From the App home screen, press the Settings button 2. Press Energy Center Settings. . FIGURE 41: Energy Center Settings Use AGS to Support This setting is used to determine if AGS will support battery levels, climate or both. 9 Battery Levels: the generator will turn on and run until the battery is charged to the set target voltage.
Run Time Limits Used to set the minimum time the generator will continue to run for after the target battery voltage and/or temperature is reached. The maximum time is the total run time that the generator will operate to reach the target battery voltage and/or temperature. If targets are not reached and the generator run time exceeds the maximum run time limit set in the Energy Settings, the generator will automatically turn off.
SOLAR CONTROLLER When solar is connected to a compatible RVC controller, the Solar Controller screen allows you to view the status of any connected solar panels. FIGURE 46: Solar Controller Tablet Screen Solar Controller This section displays the input voltage and current from the solar panel and the output voltage and current of the battery. Solar Temperature This section displays the solar controller regulator and battery temperature.
SOLAR CONTROLLER SETTINGS The Solar Controller Settings are used to configure the Solar Controller to your liking. To access Solar Controller Settings: 1. From the App home screen, press the Settings icon 2. Press Solar Controller Settings. .
Display Solar Controller Allows you to toggle Solar Controller information to be hidden if you do not want it to be displayed in the App. If Solar Controller information is hidden, you can toggle it to be displayed. Operating Status Displays the current operating status of the Solar Controller. Default State On Power Up Displays the default state of the Solar Controller when powered up. Battery Bank Size Allows you to set your battery bank size. Battery Chemistry Displays your battery chemistry.
GENERAL SETTINGS General Settings may be accessed by selecting the Settings icon home screen.
From General Settings, you can: 9 Check the Bluetooth Connection between the Node and your smartphone. 9 Set Status Settings, allowing for the setting of tire pressure sensor underpressure and over-temperature limits. 9 View Energy Center Settings. 9 View Solar Controller Settings. 9 Access a digital version of the User Manual. 9 Set Motor Settings, which depending on the level of controller installed, can be used to set zero-point calibration.
DIAGNOSTICS The diagnostics page will display any detected faults in the system. To clear circuit faults, remove the suspected short and toggle the suspected output to clear the fault indicator. 1. For lights, tank heaters, water heaters, water pumps, electric heaters or gas heaters, if a short occurs on these outputs, a red fault indicator will appear. FIGURE 53: Device Information Screen FIGURE 54: Red Fault Indicator 2. The gas water heater has its own warning output.
The Diagnostics page will display any faults detected on the Solar Controller. The following types of faults will be displayed in the Diagnostics page if detected: 9 9 9 9 9 9 9 Battery Over Voltage Battery Under Voltage Battery Over Temperature Battery Under Temperature Solar Controller Over Temperature Solar Array Over Voltage Solar Array Short Circuit NOTE: If Solar Controller information is set to be hidden in the Solar Controller settings, no solar faults will display in the Diagnostics page.
UPDATING FIRMWARE (MODEL DEPENDENT) WARNING The App will only check the Node’s firmware version if your RV is equipped with a Controller. If a Controller is part of your system, the Node will check the app revision that is installed on the Controller. If the Node has a higher firmware version than what is embedded in the App, a yellow information icon will display in the top toolbar of the App. FIGURE 57: Firmware Update Available To update the firmware: 1. Press the yellow information icon. 2.
FAQS AND TROUBLESHOOTING PAIRING WITH THE NODE 1. I tried pairing my phone to the Node, but it didn’t connect? If pairing fails, before you attempt to pair your smartphone again: 1. 2. 3. 4. Toggle the smartphone’s Bluetooth off and on. Toggle the smartphone’s Airplane mode on and off. Restart the App. Cycle power to the Node off and on. 2.
4. Navigate to the PA function on the Controller display. 5. Press and hold EXT until the number 1 scrolls across the Controller display. FIGURE 59: Clearing Devices The Node is now clear of all connected devices. 6. Pair the Controller and your device to the Node again. Refer to Pairing to the Node with a Controller. APP 1. How do I update the App on my smartphone? Most smartphones allow automatic updates. To confirm your App is up-to-date, try the following: 1. 2. 3. 4.
3. The Controller is displaying the code 88 and is unusable, what do I do? The Controller will display 88 on its menu display if there is a system error which prevents the use of the system. If you encounter an 88 error, please contact your RV dealership for further assistance. FIGURE 60: 88 Error SWITCH (MODEL DEPENDENT) 1. I’ve replaced the Switch in my RV, but it doesn’t work? You may need to pair the Switch to the Node before you can use the Switch.
APPENDICES SPECIFICATIONS NODE SPECIFICATIONS Input Voltage Range 8V to 15V DC Ambient Temperature -4°F to 140°F (-20°C to 60°C) IP Rating IP20 Approvals FCC 47 CR15, CAN ICES-3 (B) / NMB-3 (B), IEC 610004-2 Level III, IEC60068-2-27 Table A.1, IEC 60068-2-64 Spectrum A.
LIMITED WARRANTY TERMS AND CONDITIONS Registering your BMPRO product is an important step to ensure that you receive all the benefits you are entitled to. Please visit teambmpro.com to complete the online registration form for your new product today. What this Limited Warranty Covers This warranty covers any defect or malfunction in your BMPRO product. Under this warranty you are entitled to have such goods replaced, repaired or refunded.
POWERING YOUR ADVENTURES. TEAM BMPRO .COM BMPRO service@teambmpro.com Unit 1, 821 E Windsor Ave, Elkhart IN 46514 USA teambmpro.
