ASSEMBLY INSTRUCTIONS Chair So Comfortable, the moment you sit down.
Should you prefer to speak with a customer service representative, you may call toll free : 1-855-372-2315 U.S. 6am - 5pm PST 0-800-051-6775 U.K.
Guidelines FAILURE TO FOLLOW THESE WARNINGS WHEN IN USE COULD RESULT IN INJURY • Do not stand on the item or use as a step ladder • Do not use this item unless all bolts and screws are firmly secured and fastened. • Check all bolts and screws every 90 days. As necessary tighten if any are loose. • Lift up then move. Pushing over or dragging this product can result in an injury or cause damage to the floor and outdoor piece.
Pre-Assembly Preparation: Please read through this instruction booklet before beginning assembly of this item. Two adults are recommended for assembly. • Clear out the space for assembly and lay out all parts on Parts List, extra room will allow you to easily determine if all the pieces are present. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware. • Keep small parts and pieces away from children and pets until fully assembled.
Parts List (1) Seat x 1 (2) Back x 1 (4) Right Rail x 1 (5) Left Rail x 1 (3) Front Leg x 1 5
Parts List (A) Bolts 8x90 MM x 4 (B) Bolts M8 x 50 MM (C) Bolts M6x45 MM X 4 (D) Flat Washers (E) Spring Washers 9/14 MM X 9 (F) Allen Key 5 MM X 1 (G) Flat Washers (H) Spring Washers (I) Allen Key x 1 6 X5 6/12 MM X 4 9/22 MM X 9 6/11 MM X 4
Step 1-- 1. Ensure all parts have been removed from the carton and place on a protected surface or carpet. 2. Check that all parts and hardware are the same as the “Parts List”. 3. Connect Seat Frame (1) to Back (2) using with Bolt (B), Spring Washer (E) and Flat Washer (D) on the central position of Seat as shown below then tighten with Allen Key (F). 4. Please do not fully tighten Bolts (B) until the chair is fully assembled.
Step 2-- 1. Fixed with Bolt (A) Spring ,Washer (D) and Flat Washer (C) on the corner position as below image then tighten with Allen Key (E). 2. Please do not fully tighten Bolts (B) until the chair is fully assembled.
Step 3-- 1. Attach Front Legs (3) to Seat Frame (1) with Bolts (B), Spring Washer (E) and Flat Washer (D) then tighten with Allen Key (F). 2. Please do not fully tighten Bolt (B) until the chair is fully assembled.
Step 4-- 1. Attach Right Rail (4) & Left Rail (5) to Front Leg (3) & Back (2). Note: Attached the Rail end with “ To Back” sticker to Back (2) direction. 2. Fixed with Bolts (C), Spring Washer (H) and Flat Washer (G) then tighten with Allen Key (I). Noted: when tightening the bolts, please align the Rail to the edge of Leg (3) & Back (2).
Step 5-- 1. Place the counter stool onto a flat level surface and level the seat frame. Once the chair is level, tighten the Bolts (A) & (B) with Allen Key (F) fully tighten. Periodically (every 90 days) make sure that the screws are still fully tightened. ATTENTION: Be certain that all screws are fully tightened before using chair.
W42cm W16.5'' H95cm SH37.25'' D53cm D20.
Limited Warranty The product you have purchased is warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases these products from an authorized dealer or retailer as shown by the original sales receipt. This warranty does not apply too “as is” or previously owned products.
