ASSEMBLY INSTRUCTIONS Sofa So Comfortable, the moment you sit down.
Should you prefer to speak with a customer service representative, you may call toll free : 1-855-372-2315 U.S. 6am - 5pm PST 0-800-051-6775 U.K.
Guidelines FAILURE TO FOLLOW THESE WARNINGS WHEN IN USE COULD RESULT IN INJURY • Do not stand on the item or use as a step ladder • Do not use this item unless all bolts and screws are firmly secured and fastened. • Check all bolts and screws every 90 days. As necessary tighten if any are loose. • Lift up then move. Pushing over or dragging this product can result in an injury or cause damage to the floor and outdoor piece.
Pre-Assembly Preparation: Please read through this instruction booklet before beginning assembly of this item. Two adults are recommended for assembly. • Clear out the space for assembly and lay out all parts on Parts List, extra room will allow you to easily determine if all the pieces are present. • Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware. • Keep small parts and pieces away from children and pets until fully assembled.
Parts List (1) Seat Frame X 1 (5) Legs x 4 (2) Left Roll Arm X 1 (6) Seat Cushions X 3 (3) Right Roll Arm X 1 (7) Seat Cushion Covers X 3 (4) Back X 1 (8) Back Cushions X 2 5
Parts List 6 (9) Left Back Cushion Cover X 1 (10) Right Back Cushion Cover X 1 (12) Middle Back Cushion cover X 1 (A) Thumb Bolts X 4 (11) Middle Back Cushion X 1
Step 1-- 1.Ensure all parts have been removed from the carton and place on a protected surface or carpet. 2.Open the Seat (1) bottom panel and check all parts and hardware are the same as the “Parts List”.
Step 2-- 8 1.Remove the plastic caps on the threaded boles of each Wood Legs (5) as image. Attach the Wood Legs (5) to the Right Arm (3) & Left Arm (2).
Step 3-- 1.Attach Seat Frame (1) to Right Arm (3) by sliding the receivers into the mechanism posts located on sides of Arm (3), press down Seat Frame (1) then move Seat Frame (1) to attach to the Left Arm (2), press down on both sides of the Seat Frame (1) to firmly secure.
Step 4-- 10 1.Open the Seat (1) bottom panel. Insert Thumb Bolts (A) x 2 into holes where sides of Seat Frame (1) and tighten the bolts to Arms (2) & (3).
Step 5-- 1. Slide the Back Frame (4) into the Seat Frame (1) & align the bracket on the Back Frame (1) until fully engaged. 2. Open back cover then insert thumb bolts (A) x 2 into holes where sides of Back Frame (4) into holes where sides of Arms (2) & (3) and tighten the bolts. 3. Secure the back cover to the hook & loop strip.
Step 6-- 12 1.Please noted the Seat bottom panel can be lift for storage.
Step 7-- 1.Open the vacuum packed Seat Cushions (6) x3 by carefully cutting the bags with a pair of scissors. Insert the Seat Cushions (6) into the appropriate Seat Covers (7) x3 as image (1). Ensure the cushion cover completely covers the filler as image (2) When closing the zipper ensure as image (3) the cushion is compressed, this will allow the zipper to close with ease. 2.Insert the Back Cushions (8) x 2 into the appropriate Back Covers (9) & (10). 3.
Product Dimension 14
Limited Warranty The product you have purchased is warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases these products from an authorized dealer or retailer as shown by the original sales receipt. This warranty does not apply too “as is” or previously owned products.
