Executive Air™ Chair Silla Ejecutiva Aire Assembly Instructions Instrucciones de Ensamblaje Model/Modelo: 43807
Parts / Partes Casters Ruedas Quantity/cantidad: 5 Left Arm Brazo izquierdo Quantity/cantidad: 1 Star Base Base en forma de estrella Quantity/cantidad: 1 Gas Lift with Telescoping Cover Elevador neumático y cubierta telescópica Seat Plate Mecanismo del asiento Right Arm Brazo derecho Seat Cushion Cojín del asiento Back Cushion Cojín del respaldo Quantity/cantidad: 1 Quantity/cantidad: 1 Quantity/cantidad: 1 Quantity/cantidad: 1 Quantity/cantidad: 1 Chair Assembly Instructions Carefully unpack
L 1-5/8” Big Screws Tornillos grandes de 41mm Quantity/cantidad: 2 M Black Plastic Caps Tapas plásticas negras Quantity/cantidad: 2 7/8” Big Screws 1-1/4” Small Screws Tornillos grandes de Tornillos pequeños de 22mm 32mm Quantity/cantidad: 2 Quantity/cantidad: 12 1-3/4” Small Screws Tornillos pequeños de 44mm N2 O Left Arm Insert Moldura del brazo izquierdo Right Arm Insert Moldura del brazo derecho Allen Key Llave allen Quantity/cantidad: 1 Quantity/cantidad: 2 Quantity/cantidad: 2 N1 Quanti
O O Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-5/8” Big Screws (H) for the front holes of the Seat Plate (D) and 7/8” Big Screws (I) for the rear holes of the Seat Plate (D) with the Allen Key (O). *Note: Align the Seat Plate so the FRONT on the seat plate matches the FRONT label on the bottom of the seat cushion. Tighten the screws completely.
O Step 5 Place the assembled Seat Cushion (F) with Seat Plate (D) on top of the Gas Lift with Telescoping Cover (C) and press down until fully engaged. Step 6 Fasten the Arms (E1 & E2) onto sides of the Seat Cushion (F) by using 1-1/4” Small Screws (J) with the Allen Key (O). *Note: Do not tighten the screws completely.
Step 7 Place the Back Cushion (G) flat between Arms (E1& E2), and use 1-1/4” Small Screws (J) to locate lower screw holes on both Arms (E1& E2) & Back Cushion (G) with the Allen Key (O). *Note: Do not tighten the screws completely. Step 8 Push the Back Cushion (G) up to a vertical position and attach the Arms (E1 & E2) by using 1-3/4” Small Screws (K) with the Allen Key (O). *Note: Tighten all the screws completely.
Step 9 Press the Black Plastic Caps (L & M) into armrest holes to cover screws and place the Arm Inserts (N1 & N2) into arm grooves once all screws have been tightened. *Note: Remove the packing material (Y) placed between the back cushion and the air frame. Paso 9 Utilice las tapas de plástico negras (L y M) para cubrir los pernos de los reposabrazos y ponga las molduras negras de los brazos (N1 y N2) en las ranuras de los brazos una vez que haya ajustado todos los tornillos.
Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the handle. Push down the handle and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the handle to the up position. Instrucciones de Funcionamiento - 2 Para operar el seguro de la inclinación: Cuando esté sentado, busque la palanca debajo del costado izquierdo de la silla.
Function Instruction - 4 About the breathability of the Air Lumbar Cushion: While seated, the open-air contours of the cushions which are designed to breathe and flex, can dynamically provide continuous support by connecting with your body’s natural movement. The air cushions conform to the curve of your spinal cord and are intended to relieve your back from stress. *Note: It is not intended to diagnose, treat, cure or prevent any disease. If pain increases, please discontinue use.
Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned seating products.
Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así demostrado por el recibo original. Esta garantía no le aplica a muebles usados comprados “como tales”.
