MYFIT 360 Motion Support Executive Chair Silla Ejecutiva MYFIT con movimiento de 360 degrados Assembly Instructions Instrucciones de ensamblaje MODEL / MODELO 48096 Soporte máximo de la silla: 250 lbs 113 kg 250 lbs
Chair Assembly Instructions Carefully unpack all parts and identify them against the parts list before attempting to assemble. To avoid scratching the components, assemble the chair on a protected surface. Note: The casters sold with this chair are intended for use on carpet and not recommended for use on tile or hard wood floors. Using these casters on tile or wood flooring may cause floor surface damage, so please consider purchasing a chairmat to protect your floor surfaces.
PARTS/PARTES A B C D Casters Ruedas Star Base Base en forma de estrella Gas Lift with Telescoping Cover Elevador neumático y cubierta telescópica Seat Plate Mecanismo del asiento Quantity/cantidad: 5 Quantity/cantidad:1 F E1 E2 Left Arm Brazo izquierdo Right Arm Brazo derecho Quantity/cantidad: 1 Quantity/cantidad: 1 Back Cushion Cojín del respaldo Quantity/cantidad:1 Quantity/cantidad: 1 J I 1” Big Screws Tornillos grandes de 25mm 1-1/2” Big Screws Tornillos grandes de 38mm K G S
Step 1 Fasten the Arms (E1 & E2) onto sides of the Seat Cushion (F) by using 1-1/4” Small Screws (J) with the Allen Key (L). *Note: Do not tighten the screws completely. Please keep levers to the down position for easy assembling. E1 Paso 1 Fije los brazos (E1 y E2) a los costados del cojín del asiento (F) con los tornillos pequeños de 32mm (J) y la llave allen (L). *Nota: No ajuste los tornillos completamente. Favor de mantener las palancas en la posición hacia abajo para assemblar.
Step 3 Lift the lids of the EZ cable connectors attached to Seat Plate (D) as shown. Insert the ends of the arm cables into the grooves of the EZ cable connectors and snap them into place as shown. Then close the lids. Note: Fix the cables into the plastic clips attached to the bottom of the seat cushion. Paso 3 Levante las tapas de los conectores del cable EZ que se encuentran adjunto el Mecanismo del asiento (D) como se muestra.
Step 4 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). A Paso 4 Ponga la base en forma de estrella (B) con las patas hacia arriba y inserte las 5 ruedas (A) en los hoyos situados en la base (B). B C Step 5 Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top of Star Base (B).
Step 6 Place the assembled Seat Cushion (F) with Seat Plate (D) on top of the Gas Lift with Telescoping Cover (C) and press down until fully engaged. Paso 6 Coloque el cojín del asiento (F) ensamblado a la mecanismo del asiento (D) sobre el elevador neumático con la cubierta telescópica (C) y presione hacia abajo hasta que queden totalmente enganchados.
E1 Step 7 Place the Back Cushion (G) flat between Arms (E1 & E2), and use 1-1/4” Small Screws (J) to locate lower screw holes on both Arms (E1 & E2) & Back Cushion (G) with the Allen Key (L) . Note: Do not tighten the screws completely. E2 G J Paso 7 Coloque el cojín del respaldo (G) plano entre los brazos (E1 & E2), y con los tornillos pequeños de 32mm (J) ubique los hoyos inferiores para los tornillos en los dos brazos (E1 y E2) y el cojín del respaldo (G) y la llave allen (L) .
Step 9 Press the Plastic Caps (K) into armrest holes once all screws have been tightened. Paso 9 Ponga las tapas plásticas (K) en los hoyos de los brazos una vez que haya ajustado los tornillos.
Operating Instructions Instrucciones de Uso Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the arm to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height. To lower the seat, lift the lever while seated. The chair will descend until the lever is released or the chair reaches the bottom position.
Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the arm to find the lever. Push up the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the down position. Instrucciones de Funcionamiento - 2 Para operar el seguro de la inclinación: Estando sentado, sujete la palanca que se encuentra debajo del lado izquierdo del brazo.
Function Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (R) and turn it counter- clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (R) clockwise to loosen the tilt mechanism for a lighter user. Rotate the knob (R) until the desired resistance is reached.
Function Instruction - 4 Adjusting to 360 Motion Support: While seated, the 3D lumbar can dynamically provide continuous support by connecting with your body's natural movement. The 3D lumbar conforms to the curve of your spinal cord and is intended to relieve your back from stress.
Limited Warranty True Innovations seating products are warranted against defects in material and workmanship while owned by the “Original Purchaser”. The term “Original Purchaser” is defined as that party or entity which purchases True Innovations furniture from an authorized True Innovations retailer as shown by the original sales receipt. This warranty does not apply to “as is” or previously owned seating products.
Garantía Limitada Los productos de True Innovations seating están garantizados contra defectos de material y mano de obra mientras está en posesión de su “Comprador Original”. El término “Comprador Original” se define como el individuo o entidad que compra el mueble de True Innovations de un distribuidor autorizado así demostrado por el recibo original. Esta garantía no le aplica a muebles usados comprados “como tales”.
