Lucent Mars 3 PCI Modem User’s Manual Each Type A Class Machinery B Class Machinery User Guide This machinery is registered for its utilization of electromagnetic wave for business that the sellers or the users shall exercise care, and when it is sold or purchased for mistake, please replace it with one that is for family use. This machinery is registered for its utilization of electromagnetic wave for family that the sellers and the residential areas can also use this in all areas.
Copyright© 2000 Serome Electronics, Inc. All Rights Reserved. No part of this publication may be reproduced or distributed in any form or by any means, or stored in a database or retrieval system, without the prior written permission of the publisher. The contents of this User’s Manual may be changed or altered without prior notice due to the improvement or change of later products.
INDEX I. Functions of Hardware ------------------------------------------------ 4 II. System Requirements------------------------------------------------- 4 1. Operation System Requirement 2. Hardware Requirement III. Installation of MODEM------------------------------------------------- 4 1. Automatic Setting of Modem Port 2. Installation of Modem 3. Telephone Line Connection IV. Driver Installation------------------------------------------------------ 6 Installation from Windows 98 1.
I. Functions of Hardware This product provides the maximum speed of 56,000 bps (maximum of 33,600 bps in up-roading) in up-roading when data communicating, and this is an improvement of about 1.5 ~ 2 times faster than the modem that provides the existing 28,800 bps or 33,600 bps. It is an appropriate product for sending and receiving of large capacity of multimedia information which requires a fast speed and it will give you satisfaction in utilizing your internet or PC communication.
1. Automatic setting of Modem Port This product supports the PnP installation that there is no attachment of any adjustment on the modem board. However, it may be installed on the riser slot that is vacant on the main board. 2. Installation of Modem ① First, pull down the power of PC. The main board and power of recent time is mostly ATX that the complete pull off of power can prevent the damages to the other parts.
IV. Driver Installation Since the interface of this modem is PCI modem, the installation procedure for slot is slightly different than the existing ISA method. The installation method is classified into two ways. ① When OS is already installed, and ② When OS is newly installed or re-installed while a modem is installed Install from Window 98 1. When OS is already installed In such case, install PCI modem to start the operation system, the screen that has new hardware can be seen.
When forward by pressing [next], the screen for searching the position of driver is shown as below. Screen asking for the position of driver The above designates the location of driver. Normally, the driver supplied from CD-ROM or floppy disc. Designate the location by inserting CD-ROM or floppy disc. Obviously, in the Windows 95, designate the driver position by similar method but not by the same message. Finding Equipment Then the message that it is ready is shown.
Installation Completed The hardware driver installation of modem is now finished. 2. OS is newly installed or re-installed The following is the description for operation system that is newly installed or re-installed. The following case is registered by the unknown equipment which is evident from looking at the [Device manager] in the [system] of [control Panel]. By deleting it and re-booting, a message that new hardware is found is shown. Then install the drive by way of “1.
2. As shown in the below, find PCI Device from the PnP and select ‘Search for proper driver for installation (recommend)(S)’. New Hardware Addition Engine 3. When a screen asks the path of drive as shown below, press ‘Specify a location’. Screen searching the driver Installation path 4. Path name of the installation file may be inserted directly or designated by the user or it is designated.
Screen Found the Initial File 5. Search for ‘Lucent Win Modem’ driver as shown below. Continue installation here. Screen Found Driver 6. When the file necessary in installation is copied in the system, the installation of modem is complete. Completion of New Hardware Search Engine 7. Re-boot and use it after completing the new hardware search engine.
V. Confirm the Installation of MODEM Confirm from Windows 98 1. Setting of Modem at [manager] Click the [system] button of [control panel] as follows, and then look at the [Device Manager]. Opening Control Panel The modem has to be installed as the following picture. Manager In order to install the hardware of modem, look at the registration information of There are several items in it. “Lucent Win Modem”.
It may be confirmed whether the modem is operated in accordance with . Registration Information The modem maximum speed and the volume of connection sound can be adjusted as shown in the . Registration Information As shown in the , it may be set in accordance with the condition of communication network, but generally it is recommended to set with the basic value.
Modem Registration Information The following is the screen that shows when pressing the ‘Port Settings’ on the above screen that 16550 FIFO set may be made here. Modem Registration Information and are screens that are shown when [Port Settings..] and [Advanced..] are pressed in the screen and these also are left at the basic value.
Modem Registration Information The following picture may show the information on the upgrade of driver or present version information. Driver Information From the below picture, resource of system that the modem has can be known. When receiving customer support services with problems, this information may be useful.
Resource Information 2. Modem Setting from the [control panel] Now look at the [control panel]. Search for modem and refer to the item, then the screen like is shown.
Confirm the modem in this screen. And, click [diagnostics] tap, then the screen like is shown. Diagnostics Information After positioning the mouse cursor to the COM port that modem is installed as shown in the , click the button. Then, the screen like is shown momentarily. [More info] Modem Additional Information If reading is normally made in this screen, the purchased product is normally installed and is in an operable condition.
Confirm from the Windows 2000 1. Modem Set at the [Device Manager] Click the [System] of [Control Panel] as shown in the below, look at the ‘Device manager (D) of [Hardware] tap. Opening Control Board Modem has to be set as in the below picture. System Manager In order to have hardware set of modem, double click the “Lucent Win Modem” to see the registration information. There are several items inside.
Registration Information The maximum speed and the scale of connection sound of modem can be adjusted as shown in the . Registration Information is indicative of hardware support that the modem takes in this system, and when the modem is normally installed, the following diagnosis is shown as in the below picture when ‘Query modem ’is pressed.
Modem Registration Information The below picture is a part that shows the high quality function of the modem with which it can insert the initialize command for the modem.
The following is the screen that is shown on the above screen when ‘Advanced Port Settings’ is pressed and it can be set at 16550 FIFO. Modem Registration Information The following picture is the screen that shows when ‘Change default Preferences‘ is pressed, and the values of ‘Advanced’ is set at the basic value in general. ‘General’ and Modem Registration Information The next picture may upgrade the driver or remove the current version information or driver.
Modem Registration Information The resource of system that the modem has can be known from the below picture. This may be valuable when you receive customer support for your problems in the future.
