M-CNX-DSL-PCI2 Quick Installation Guide ! Unpacking the Box 2 PAGE " Before Installing 3 PAGE # Installing the M-DNX-DSL-PCI2 4 PAGE $ Installing Software Driver on Windows 98 5 PAGE % Installing Software Driver on Windows 2000 8 PAGE & Connecting the Network 11 PAGE
! Unpacking the Box After the shipping carton carefully and check the contents include the following items. If any items were not delivered, please contact Medialincs or your product provider.
" Before Installing Hardware Requirement The following hardware and software requirements are necessary to configure and use the M-CNX-DSL-PCI2: Item CPU Operating system Main memory CD-ROM drive PCI slot Specification Pentium II 300MHz or compatible processor Window 98/98 Second Edtion/2000/NT 4.0 32MB (Recommended : 64MB) CD-ROM drive necessary to install the software driver PCI expansion slot for the M-CNX-DSL-PCI2 Necessary Information Before installing the M-CNX-DSL-PCI2.
# Installing the M-CNX-DSL-PCI2 The following procedures show how to install the M-CNX-DSL-PCI2 in the PC. 1. Power off the your computer and disconnect the power cord. 2. Open your computer and find the empty PCI slot. Remove the cover of the PCI slot. 3. Slide the M-CNX-DSL-PCI2 ADSL modem into the empty PCI slot, push it gently. Using the screw loosen in step 3, fix the M-CNX-DSL-PCI2 ADSL modem. 4. Close the computer and connect the power cord. Don’t press the power switch yet.
$ Installing Software Driver on Windows 98 This section describes the following procedures on a Windows 98 or Windows 98 second edition system to use the M-CNX-DSL-PCI2 ADSL modem. ' ' ' Installing the software driver Setting the VPI, VCI WAN driver : Creating a new connection profile / LAN driver : Setting the TCP/IP Installing Software Driver M-CNX-DSL-PCI2 ADSL modem software driver is composed of the following three device drivers.
Setting VPI and VCI 1. Click Start * Setting * Control Panel. 2. Double-click Conexant AccessRu… icon in window. 3. window appears. Press the [Alt + P] keys simultaneously. 4. Then, several tabs are added to the window. lick Setup tab and specify the VPI and VCI values in the Virtual Path Identifier and Virtual Connection Identifier field. Click the [Apply] button and click [OK].
Setting the TCP/IP : In Case of the LAN Driver 1. Click Start * Setting * Control Panel. 2. In the window, double-click the Network icon. 3. The window appears. Select ‘Conexant AccessRunner PCI ADSL LAN Adapter’ and click the [Properties] button. Select this item, And click [Properties]. 4. window appears. Click the ‘IP address’ tab.
% Installing Software Driver on Windows 2000 This section describes the following procedures on a Windows 2000 system to use the M-CNX-DSL-PCI2 ADSL modem. ' ' ' Installing the software driver Setting the VPI, VCI WAN driver : Creating a new connection profile / LAN driver : Setting the TCP/IP Installing Software Driver M-CNX-DSL-PCI2 ADSL modem software driver is composed of the following three device drivers.
Setting VPI and VCI 1. Click Start * Setting * Control Panel. 2. Double-click Conexant AccessRu… icon in window. 3. window appears. Press the [Alt + P] keys simultaneously. 4. Then, several tabs are added to the window. Click Setup tab and specify the VPI and VCI values in the Virtual Path Identifier and Virtual Connection Identifier field.
user name and password provided by your Internet server provider and click [Next>]. 10. The window for specifying the connection name for dial-up connection appears. Enter the name of the connection used for connecting the network later and click [Next>]. 11. prompts you the completing the wizard. Click [Finish] button. And you can connect the Internet from now on. Setting the TCP/IP : In Case of LAN Driver 1.
& Connecting the Network In Case of WAN Driver On Windows 98 1. Double-click My Computer icon. The My Computer window appears. Double-click the Dial-Up Networking icon in dialog box. 2. The following windows apeear. Enter the user ID and the password and click [Connect] button. ) Contact your Internet service provider for user ID and password. 3. While the system tries to connect the network, the following window appears. 4.
On Windows 2000 1. Click Start * Settings * Network and Dial-up Connections. 2. The windows apeears. Enter the user name and the password and click [Dial] button. ) Contact your Internet service provider for user ID and password. 3. While the system tries to connect the network, the following window appears. 4. If you connect the network successfully, the following icon is added to the tray in the desktop. 5.