SLSPSKT200 2 Pcs. Portable Mono Solar Panel Starter Kit 100W with 3 ft.
Please read the manual carefully before installing or operating the Portable Mono Solar Panel Starter Kit to prevent personal injury or damage to the components. Contact Technical support for any questions concerning the installation. INTRODUCTION This manual provides the installation and operation instructions for users: • Please carefully read this manual before installation, operation and maintenance of our solar system.
PACKING LIST V AH 100W Solar Panel A *1 100W Solar Panel B *1 Mounting brackets *2set Wire fixer *10pcs Controller 30A*1pc Extension lead 11AWG * 20ft Fuse 15A*1pc Battery lead 11AWG * 8ft INSTALLATION WITH ROOF RACK 1 2 Z-shape bracket *4pcs Double nut aluminum plate *4pcs 4 ONE SET of mounting bracket included 3 Ø8 Bolt (M8*16) *4pcs 5 6 Ø8 Nylon lock nut Ø8 Bolt flat mat *4pcs *12pcs 7 Ø8 Bolt spring washer *8pcs Ø8 Bolt (M8*25) *8pcs 8 Ø8 Big Bolt flat mat *4pcs www.
Step1: The connection of solar panel and Z-shape bracket. 4 8 INSTALLING HOLE 5 3 Step2: Connection of Z-shape bracket, double nut aluminum plate and roof rack. 1 6 7 5 Roof Rack 2 3 www.SereneLifeHome.
Step3: System Wiring as follows 100W Solar Panel A *1 100W Solar Panel B *1 See controller manual P6-P8 Controller Fuse Battery Output INSTALLATION WITHOUT ROOF RACK Refer to the above installation guide, and 2 double nut plate are not used. APPLICATION CASES Our solar system can be widely used in RV, 4WD, tourist car, yacht and roof power generation system, etc. www.SereneLifeHome.
MAINTENANCE • Solar panels are generally self-cleaning, but in particularly dry areas or where panel tilt is minimal, dust and other substances such as bird droppings can build up over time and impact on the electricity amount generated by the panels. Clean the panel surface with a soft cloth or sponge using clean and neutral water. Other ways of cleaning may scratch the surface coating on the glass.
CONTROLLER MANUAL SAFETY INSTRUCTIONS • This controller is a 12V/24V controller. Make sure your battery has enough voltage (12V/24V) for the controller to identify the correct battery type before first installation. • Install the controller as close as possible to the battery to avoid voltage drop caused by long wire and affect normal voltage judgment. • The controller is suitable for 12V/24V lead-acid batteries, lithium-ion batteries and LiFePO4 batteries.
MENU: Switch between different interface, or to enter/exit parameter setting by pressing and hold. UP: Press to increase value DOWN: Press to decrease value SYSTEM CONNECTION • Connect the battery to the controller with the correct polarity. • Connect the solar module to the controller with the correct polarity. • Connect the load to the controller with the correct polarity. The reverse order applies when uninstalling! Improper sequence can damage the controller! INTERFACE / SETINGS Main interface.
Charging current interface. A Discharging current interface. A Charging voltage adjustment interface. When the battery voltage rises to the set voltage, it will maintain constant voltage charging. Press and hold the MENU key to make the number flicker, and press UP/DOWN to the required voltage, then long press MENU key to exit. V Low-voltage recovery adjustment interface.
D2D trigger delay value (Unit: second) When the controller detects that the voltage of solar panel is lower than the set trigger value, it delays 10S to turn on the load. This time value can be used to prevent the night car lights or lightning interference leading to wrong judgment and turn off the lights. Default value is recommended. The setting method is the same as above. Short circuit protection setting interface.
FAQ Q: Why won't my solar panel display charging when connected? A: Check whether the connection of solar panels is correct, whether there is reverse connection, whether the voltage of solar panels is higher than that of batteries, and whether solar panels are blocked that causes voltage drop. Under normal circumstances, 12V batteries should use solar panels with rated voltage of 18V.
TECHNICAL PARAMETER • All grey color voltage X2, while using 24V system. • Product specifications are subject to change without prior notice. What's in the Box: • (2) 100W Mono Solar Panel • (2) Sets of Mounting Brackets • (10) Wire Fixers • 3 ft. 11 AWG Cable Set (Connected already with Solar Panel Junction Box) • 20 ft. 11 AWG Sheathed Cable Set with Aviation Connector • 8 ft. 11 AWG PV Cable Set with Ring Terminal • 15A Fuse • 30A PWM Controller 11 www.SereneLifeHome.
Features: • Includes 30A PWM Controller with LCD Screen • Portable and Easy Set-Up • Sleek Design for Aesthetic Quality • Grade A Mono Solar Cells • Higher Module Conversion Efficiency • Optimally Generate about 67Ah in 12V Battery or 800WH per Day • Anodized Aluminum Frame to Protect Solar Cells & Convenient for Installation • Foam Box for Safe Transport and Easy Storage • Dust Tight and Waterproof with IP67 Rating • Set Up in Just 5 Minutes for Solar Starters • Used for Marine, Dry Camp, RVs, and Other Of
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: support@pyleusa.
