SLPPTB22 Durable Indoor Table Tennis Table Designed with MDF Table Top for Optimal Bounce
IMPORTANT SAFETY NOTICE For your safety and benefit, read this manual carefully before starting assembly and using this product. Failure to follow the instructions and safety precautions in this manual can result in serious injury or damage to equipment. SAFETY INFORMATION: • DO NOT allow children to open table. ADULTS ONLY should open, close, adjust, or move table. • DO NOT leave children unattended with table. • DO NOT climb, sit, jump, lean, or stand on table.
HARDWARE LIST PAGE P2 P1 H4 Caster Beams 2.PCS P3 Table Tennis Table Top 2.PCS Support Tube 4.PCS P7 P6 Strut Tube 4.PCS Accessory Holder 3.PCS TOOLS REQUIRED FOR ASSEMBLY (NOT INCLUDED) H1 5/16" Wrench (x2) H2 Bolt M10x110MM 4.PCS Bolt M10x75MM 8.PCS Bolt M6x45MM 4.PCS M10 Plastic Washer 8.PCS M6 Lock nut 6.PCS M10 Plastic Spacer 4.PCS H12 M8 Plastic Washer 4.PCS M6 Plastic Spacer 4.PCS H14 M10 Washer 24.PCS M10 Lock nut 12.
STEP 1 Hardware Needed: H2 Bolt M10x75MM 8.PCS H13 M10 Washer 16.PCS H17 Stop Spool 8.PCS H18 Triangle Support Plates 4.PCS H6 M10 Lock nut 8.PCS P2 Caster Beams 2.PCS WARNING: Clear area of small children and pets 4 www.SereneLifeHome.com • Before beginning, ensure you have cleared an area large enough for the table to be assembled. • Align Triangle Support Plate with Caster Beam to line up holes.
STEP 2 Hardware Needed: H4 Bolt M8x60MM 4.PCS H7 M8 Lock nut 4.PCS H14 M8 Washer 8.PCS P2 Caster Beams 2.PCS P3 M10 Lock nut 8.PCS • Attach Middle Plate (P3) to Caster Beams (P2) as shown in the above image. • Thread the Bolt (H4) through the Washer (H14), both Steel Frames, another Washer (H14) and secure with Lock Nut (H7). • Repeat for both Caster Beams then tighten completely. www.SereneLifeHome.
STEP 3 Hardware Needed: H1 SHORT END Bolt M10x110MM 4.PCS H6 LONG END M10 Lock nut 4.PCS H9 M10 Plastic Spacer 4.PCS H10 M10 Plastic Washer 8.PCS H13 M10 Washer 8.PCS H18 Triangle Support Plates 4.PCS P2 Caster Beams 2.PCS P4 Support Tube 4.PCS P5 Strut Tube 4.PCS 6 www.SereneLifeHome.com CAUTION: DO NOT overtighten the nuts, as this will apply too much pressure to the spacers and may cause them to crack.
STEP 4 WARNING: Gray support tubes will protrude into assembly area, posing a potential tripping hazard. Exercise caution when completing the remaining assembly steps. • Place the Strut Tubes (P5) in a upward position and lay the Gray Support Tubes (P4) down in front to avoid interference while attaching the Table Top. www.SereneLifeHome.
STEP 5 Hardware Needed: P1 Table Tennis Table Top 2.PCS WARNING: • At least (2) to three (3) adults are required for the following steps. • DO NOT attempt to assemble alone, as this may lead to serious injury. • DO NOT open the table to playing position until all support beams and hinges are attached to table frame. • DO NOT leave table unattended in standing position. Table could be knocked over, causing serious injury or property damage. 8 www.SereneLifeHome.
STEP 6 Hardware Needed: H3 Bolt M8x60MM 4.PCS H14 H3 H14 H7 M8 Lock nut 4.PCS P4 H11 H7 M8 Washer 8.PCS P4 Support Tube 4.PCS H14 H7 H11 M8 Plastic Washer 4.PCS H14 H11 H3 H14 CAUTION: DO NOT overtighten the nuts, as this will apply too much pressure to the spacers and may cause them to crack. WARNING: • DO NOT open the table to playing position until all support beams and hinges are attached to table frame. • DO NOT leave table unattented in the upright position.
STEP 7 Hardware Needed: H16 3.0x12MM Screw 4.PCS WARNING: • DO NOT open the table to playing position until all support beams and hinges are attached to table frame. • DO NOT leave table unattented in the upright position. Table is not secure yet and can be knocked over causing bodily injury or property damage H16 H16 • Install screws (H16) into the pre-drilled holes on the Black Strut Tubes (P5). 10 www.SereneLifeHome.
STEP 8 Hardware Needed: H5 Bolt M6x45MM 4.PCS H8 M6 Lock nut 4.PCS H12 M6 Plastic Spacer 4.PCS H15 M6 Washer 8.PCS P5 Strut Tube 4.PCS WARNING: • DO NOT open the table to playing position until all support beams and hinges are attached to table frame. • DO NOT leave table unattented in the upright position.
STEP 9 Hardware Needed: P6 P6 Accessory Holder 3.PCS H8 M6 Lock nut 2.PCS H16 M6x15mm Phillips Head Machine Bolt 2.PCS H19 H19 H8 Accessory Holder • Assemble Accessory Holder by positioning one of the plastic pieces over one of the pre-drilled holes on the H frame. • Screw into the frame with a bolt (H19). • Secure the middle metal piece by tightly fitting it between the two plastic pieces. • Finish the assembly by screwing in the other plastic piece with a bolt (H19).
STEP 10 WARNING: • Area should be clear of children, pets, and any other obstacles when moving the table in different position. • DO NOT allow children to climb between, under or over any part of the table. • Adults only should move or open/close the table. • NEVER leave table unattended in standing position without properly stored. Table could be knocked over, causing serious injury or property damage. • NEVER leave table partially opened or not fully secure.
Putting the Table Play-Back and Play Mode • After correctly assembling both Table Tops, your table can safely be moved from storage mode (Figure 1) to the play-back (Figure 3) or normal (Figure 4) play position. • Grab the center of the top edge with both hands. WITH CAUTION, gently pull the table outward until you feel the legs rest on the floor as shown. • Secure table by locking the hinges on both sides of the tabletop. Hinges will lock by pushing up on the elbow. • Repeat steps for the other Table Top.
STEP 11 Hardware Needed: P7 Net Clipper 2.PCS P8 Net 1.PCS • Now that your table is in play position, you are ready to assemble the net. • Secure the Net Clipper (P7) to your Table Top (P1) by clipping it near the center of the two Table Tops. NOTE: If you plan on putting the Table in storage mode, you will want to clip it to only one Table Top surface as close to the center as possible. The Net Clipper can be moved back once the table is in play position again.
Features: • Box Steel Apron for Durability • Comes with 50% Pre-assembled • Easy Set-up by Two People in just 40 minutes • Includes Net and Clip Set • For Indoor Use Only • DSG Exclusive • Swivel Wheels with Locking Casters for Safe Transport • Matte Grey Finish • 4/5"x2” Box Steel Apron • Foldable Design and Simple & Fast Assembly • Integrated Paddle and Ball Storage • Leg Levelers and Bumper Corners for Stability and Protection What's in the Box: • Table tennis table • Net and clip set • Instruction book
www.SereneLifeHome.
Questions? Issues? We are here to help! Phone: (1) 718-535-1800 Email: support@pyleusa.
