SERENE vil LEY Model SVSD5002 GETTING STARTED Notice: This assembly requires two people due to the weight of the grass doors. Professional installers are highly recommenced. 1. Carefully inspect all boxes and packages to make sure no damage 4. Finished floor and walls are required for installation of this unit. occurred during shipping. If you find a unit has been damaged or has a finishing defect, contact our customer service for replacements. 5.
SERENE VALLEY: sg 8 PARTS LIST Bo a (2) Door stopper. (1) Glass panel (1x) Top guard rai (2x) Roller (1x) Lassa panel (1x) Handle (2) Glass bracket (2) Good tall bracket: (2% Large anchor 3/8" (2%) Screw Stetted A (1x) Allen lays Som; men & Sims (1) Guide book (2) Bumper try 1x) Threshold cover: (1) Threshold (5%) Sorrow 8T4.230 (2x) Water proof strip: (5%) Small anchor 5/18: (2) Roller guard (1) Silicone cleaner.
SERENE vil LEY Model SVSD5002 MEASUREMENTS 1. Take a precise measurement of the distance between the two completed walls. This distance Is labeled as “W" on the diagram. Refer to Figure 1 for details. 2. For your convenience, the Top Guide Rail (03) has been precept for shower models with a width Wall-to-wall openings with a width (W) equal to the size of the shower mode! does not require you to cut the Running Rail (03). Simply continue to Step 3.
SERENE vil LEY Model SVSD5002 GLASS BRACKETS B 3.Use the Glass attach the Upper Guide Rail (03)to the Stationary Glass the set with screws. Place the Door Stoppers {01} on each end of the Top Guide Rail {03} by using a sliding motion(Note :While place the Door Stoppers (01) must be vertical as the upper guide rail {03}, Correct installation method secure them. Place the Guide Rail Brackets (08) on each end of the Top ef Guide Rail (03) by using a sliding motion. Temporarily secure them.
SERENE vil LEY Model SVSD5002 STATIONARY GLASS 4. Rest the Stationary Glass {02) on the p Reinstalled threshold or shower base and push It — up against the wall. holey position NOTE: The Top Guide All (03) secured the Stationary Glass should face the interior of the shower. Be sure the Top Guide All and Stationary Glass are aligned with the threshold or shower base and are fully leveled. Make = adjustments to the Glass Bracket (07) If horizontal adjustments are necessary. I / \ Refer to Figure 3 for details
SERENE vil LEY Model SVSD5002 GUIDE RAILS 5. Carefully make an outline on the wall of the Guide Rail Brackets (08) position. Set aside the Stationary Glass (02) while you disassemble the Guide Rail Brackets from the Top Guide Rail {03). Position the Rail a Bracket into the outlined areas and precisely mark drilling holes. fox Refer to Figure 4 for details. 6. Use a @ 3/8" drill bit to dll the holes for the Guide All Brackets (08). Insert the “Large Anchor 3/8” (09). 7.
SERENE vil LEY Model SVSD5002 GUIDE RAILS Attach both female parts of the Guide Rail Brackets (08) to their male counterparts on the wall. Adjust the set screws on the Guide All Brackets until they are tight and fully secure the Top Guide Rail between the walls. Gently set the Guide Block (12) on the floor, parallel to the Stationary Glass Panel flush with the vertical edge of the glass.
SERENE vil LEY Model SVSD5002 ROLLERS 11. Affix the Rollers (04) to the Glass Panel (05). Hang the Rollers onto the Top Guide Rail (03) to suspend the door. Slide the lower edge of the Glass Panel into the groove found on the Guide Block (12). Make necessary adjustments to the fasteners to guarantee the lower edge of the Glass Panel does NOT touch the bottom of the Guide Block. Secure the door to the Top Guide Rail by mounting the two Roller Guards (20) on the door. 12.
SERENE vil LEY Model SVSD5002 ROLLERS 14. Add Kitchen and Bath silicone along the area where the Stationary Sa Glass and Wall and the Threshold or Shower Base connect. Clean the silicone using the Silicone Cleaner (20) tool. WARNING: WAIT 24 HOURS BEFORE USING THE SHOWER ENCLOSURE TO ALLOW THE SILICONE GEL TO DRY COMPLETELY. Guarantee a longer life of the hardware finish by wiping off the metal parts with a soft cloth after each use.
SERENE vil LEY Model SVSD5002 MAINTENANCE Guarantee a longer life of the hardware finish by wiping off the metal parts with a soft cloth after each use. Avoid using abrasive cleaners and products especially those that contain bleach, acid, or ammonia. In the case that these chemicals are used, thoroughly rinse the surface as soon as possible and wipe dry with a soft cloth. Stainless-steel surfaces should be cleaned once a week or as needed.
